4 trim ring and snap-in mounting clips for IQ8Quad detector base
6500-MMK multi-mounting kits allow 6500 beam smoke detectors to be mounted to ceilings or to walls where the detector and reflector cannot be mounted within 10° of one another. One kit mounts either the transmitter/receiver unit or reflector.
6500-SMK surface-mount kits are intended for use with beam detectors to mount transmitters and receivers when using 6500-MMK multi-mounting kits.
ABS elbows and brackets for aspirating smoke detectors
ASD ADPTR 25MM ABS TO 22MM COPPER
RF-FTX Additional filter accessories are used for HPX-751E HARSH ™ analog addressable aspiration detectors.
Angle Brackets by Gent are designed for use in areas where beam detector will not be installed to a vertical surface, or where the beam path is not perpendicular to the installation surface.
Anti Condensation Film is an easy applicable film that provide long time resistance to condensation on the acrylic Emitter lens
Anti-Condensation Film is used for OSID-EH housings. An easy applicable film that provide long time resistance to condensation on the glass fronts.
ISP-104 from Xtralis are aspirator fans for IFT-P, IFT-4 and IFT-6 detectors.
F210 flanged rings are designed for use with B210LP detector bases.
F110 flanges are replacements for the flanges on B400 Series detectors.
Heating kits for use to prevent condensation with the BEAM1224 conventional beam smoke detectors. They lessen the likelihood of condensation by maintaining the unit at a temperature that is slightly higher than the surrounding air.
BEAMMMK multi-mounting kits allow reflectors and reflected beam detectors to be mounted to either vertical walls or ceilings.
Battery Holder Kit is a Marine System Component designed for Marine battery box.
S-Quad Beam Sensors provides an enhanced solution for linear beam detection for applications where point detection is either not practical or economic.
Gent by Honeywell’s S-Quad Beam Sensors provides an enhanced solution for linear beam detection for applications where point detection is either not practical or economic.
Beam Sensor Transmitter mounted on a base fixed to either bracket allows the detection of smoke over distances from 2 m to 100 m each mounted on a base fixed to either bracket.
CO detector replacement plate to cover the footprint of previously installed detectors.
The SENS-RDR utilizes infrared technology to read the sensitivity of i3 and 100 Series conventional detectors.
The ES Detect automatic detector is an intelligent nonaddressable detector specifically designed for operation on conventional detector groups
Detector test magnets simplify detector testing and maintenance
Single Terminal Back Boxes are used for mounting RTS151 key. Remote annunciator accessories providing reset function and has a Red LED to indicate alarm conditions.
EMC shield for IQ8Quad, ES Detect detector base
EXT steel exhaust tubes are intended for use with HVAC duct smoke detection and monitoring products.
VSP 850 in-line filters provide Xtralis® customers the ability to address a wide array of harsh environments with high levels of airborne contaminants in a simple and cost-effective manner.
Hand-held remote control is designed to communicate with Eclipse devices via infrared signals.
Sampling Hole Clips are designed to alleviate such potential issues, by providing a clear, visual indication of sampling point location and its associated hole size.
ISP-406 is used as a cover removal tool for IAS or ILS
Xtralis ICAM Accessories offers Medium and fine filter elements for the internal filters inside the ICAM IFT, ICAM IAS and ICAM ILS series detectors. Replacement filters elements are available in pack of 10 with Black colour
ISP-114-01 from Xtralis are detector chambers for ICAM IFT-P detector.
IQ8Wireless mounting frame for IQ8Quad detectors, white
ICAM FLOW SENS ASSY IAS/ILS
Installation/removal tools are designed for use with System Sensor® plug-in smoke detectors. They permit installation and removal of detectors in elevated mounting locations.
Intelligent Detector Color Kits are designed for use with NOTIFIER® intelligent detectors.
L-Series bezel kits enable installers to easily turn any L-Series fire or plain device into a device that meets ECN/MNS requirements.
VESDA Aspirating Pipe and Fittings are produced in redABS under a stringent quality control system.
Label-smoke detector pipes are manufacture from ABS (Acrylonitrile Butadiene Styrene), very lightweight, versatile material, guaranteeing you easy and professionalinstallation.
Light shield is available for installation in areas where direct sunlight cannot be avoided
The DST family of sampling tubes are pieces of steel piping with a series of holes drilled the entire length of the tube and should extend the entire width of the duct.
Multi-voltage conventional relays are used for high-current switching applications such as fans and damper assembly controls, door controls, air handling unit controls, and other types of system interfacing.
OSID wire guards are steel cages designed to protect OSID imagers and emitters from vandalism and accidental damage. The cages are constructed of heavy gauge steel wire with a corrosion-resistant polyester coating.
OSID environmental housings protect OSID imagers and emitters from dust and water ingress in industrial environments. The glazed housings are made of ABS and the glass windows cause minimal attenuation of the UV and IR beams.
Installation kits for OSID detectors include a laser alignment tool, a test filter, a PC cable, a cleaning cloth, and a manual.
OSP-002 laser alignment tools allow for quick alignment of OSID detectors. They also align and lock the eyeball and activate the emitters when locked.
OSP-003 acrylic test filters are intended for use with OSID detectors.
P48-21-00 end caps for metal sampling tubes are intended for use with conventional and intelligent duct smoke detectors.
Gent S-Quad Sensor Bases are used for all S-Quad Sensors. Available in White or Black.
Sockel mit integriertem Isolator für den Notifier - Ringbus für Melder der Serie 700
B401 plug-in detector bases are used with System Sensor® conventional S300 smoke and heat detectors. These bases make detectors more versatile than equivalent direct-wired models.
SMB600 flanged surface mounting kits may be used with certain System Sensor® smoke detectors when flush or recessed mounting are not possible.
ST metal sampling tubes may be installed from the front or back of System Sensor® HVAC duct smoke detection and monitoring products. The tubes lock securely into place and can be removed by releasing the front or rear locking tab.
The STI is an accessories that are been used with STI Stopper II®. The accessories that are been used are conduit gasket and conduit spacer.
The System Sensor SWIFT® Wireless system offers an AV base to support L-Series devices in wireless installations.
Semi-flush fixing kit is designed to mount an S-Quad device. To semi-flush mount a special housing must be used which consists of a main assembly and a trim ring.
Single Row Blanking Plates are used to fill the enclosure if less sub racks are used than the enclosures maximum.
Gent Nano Spares Pack
Sampling Hole Clip delivers reliable & accurate sampling hole sizes that are fast to install & easy to locate. Each clip is colour-coded to indicate a specific hole diameter providing an instant visual guide & removing the need for closer inspection.
System Sensor BEAMSMK are the surface mounting kit for the reflective projected beam smoke detector which are used whenever surface wiring is being used.
Top Hat Rail is available in 400mm.
Xtralis VESDA Wall-Mounted High Level Interface (HLI) links VESDAnet1 with PC software monitoring tools, Building Management Systems (BMSs) and Fire Alarm Control Panels (FACPs).
VESDA Pipe and Fittings are part of an integrated system manufacturedfrom specialty plastics designed for use with most aspirating smoke detectionsystems, the VESDA VLP system in particular
VESDA-E Filter Cartridge is field replaceable filter of VESDA-E detectors. It filters coarse particles
VESDA® pipes and fittings make up a network of dependable specialty piping that constantly and efficiently carries air samples from protected zones to highly sensitive detectors.
VESDA® VPS100/300 and power supplies are capable of providing operating power, including battery backup, for the entire line of VESDA by Xtralis® aspirating smoke detectors.
VESDA® filter cartridges are used to replace filter cartridges in VESDA VLC, VLF, VLP, and VLS detectors.
VP-CLIP 3/4-inch pipe support clamps are designed for use with VESDA® pipes. They are required for each five foot length of pipe.
VESDA SCREW COVER PK2
Pipe – 3⁄4”
Vigilion Beam Sensor Recievers are a part of Vigilon’s loop powered technology which allows 16 beam pairs to be connected to the same loop circuit, each covering a distance of up to 100m.
Metric to Imperial Pipe Adaptors, Kit
The System Sensor A77-AB adapter rings allow installers to retrofit i³™ Series detectors where a larger diameter smoke detector was previously installed.
Start your search with category name, product name, part number, etc.
Copyright © 2023 Honeywell International Inc.