Controller Input/Output Modules
Input monitor modules have 10 inputs and interface between a control panel and normally open contact devices in intelligent alarm systems, such as call points, security contacts, or flow switches.
Notifire offers 10 relay outputs module. The output of each module is a voltage free switch contact designed to switch resistive loads up to 2A/30 Vdc.
Each input and output are individually addressed and controlled by the control equipment and provide a cost effective, compact solution for installations requiring multiple switching and/or monitoring at a single location
Duct smoke detector power board replacements replace the 4-wire duct smoke detector power boards, which are available as either an ionization or a photoelectronic model.
4204 intelligent relay boards add relays which are connected to the control/communicator via the control console wiring. The relay outputs are programmed by the appropriate control for a variety of functions.
4XZM zone relay modules provide four Form C relay contacts to fire alarm control panels (FACPs).
5-way output and 5-way input interface module card for use with Notifier Analog addressable fire alarm systems. This card is un-boxed and requires a 002-439 multi mount enclosure for installation.
5820XL LED I/O driver modules provide an effective means to customize your remote annunciation. They provide LED annunciation and control inputs for the fire alarm control panel (FACP).
Supervised control modules are 6-circuit and provide intelligent alarm systems with supervised monitoring of wiring to load devices that require an external power supply to operate, such as horns, strobes, or bells.
8 way input/output cards Provide up to 8 configurable relay outputs or up to 4 command inputs and 4 outputs.
ADPRO® Ethernet I/O base units with LED indicators, contact inputs, and relay outputs are controlled by an ADPRO NVR+ device (FastTrace™ 2 Series, iFT Series, iFT Gateway).
ANN-I/O LED driver modules interface with fire alarm control panels (FACPs) to drive most customized graphic annunciators.
ANN-RLY relay modules provide 10 programmable Form C relays when used with compatible fire alarm control panels (FACPs).
Addressable 6-relay control modules are designed for use with Honeywell Silent Knight® Series fire alarm control panels (FACPs). They come equipped with six Form C relays and allow the FACP to switch discrete contacts through a code command.
Addressable 6-zone interface modules transmit the status of 2-wire detector zones to Silent Knight® fire alarm control panels (FACPs). Status conditions are reported as normal, open, or alarm.
Addressable dual monitor modules come equipped with two initiating circuits that are designed to be used with the Honeywell Silent Knight® Series fire alarm control panels (FACPs).
Addressable zone interface modules are intelligent 2-wire interface modules designed for use with the Honeywell Silent Knight® Series fire alarm control panels (FACPs).
Agile-IQ USB Dongles are USB-Radio Frequency Interface for Windows PC for the use of the Agile-IQ Configuration software -maintenance and testing
The ID3000 is a flexible, modular control panel, built from various option modules. Each module is supplied with required mounting screws, connection cables, washers etc. and installation instructions.
Audible isolation modules operate with standard 24V DC audio devices and 25 to 70V AC speakers. They can be used with one to four unsupervised suite circuits.
CB500 wiring barriers are used to separate power-limited and nonpower-limited wiring inside of junction boxes.
CDRM-300(A) dual relay/monitor modules are designed for use with Fire-Lite® Fire Alarm Control Panels (FACPs). These addressable modules are intended for use in intelligent, 2-wire loops.
CMF-300 addressable control modules provide Fire-Lite® alarms' intelligent control panels with a circuit for notification systems, such as horns and strobes.
Circuit zone expander modules provide connections for up to four or six Style Z (Class A) or six Style Y (Class B) speaker circuits.
Compact Remote Display Module monitors and reports the status of a VESDA aspirating smoke detector.
M200E-DIN provides a DIN rail mounting option for one module of addressable Honeywell Morley-IAS series modules.
DXc System IO Card Interfaces are used in DXc1-M (714-001-214) & DXc2-M (714-001-224) fire alarm control panels. This I/O cards are used in sounder circuits, Fire Routing interface, Fault Routing interface and Fire Protection interface.
The Digital Key Module DKM plus offer 18 freely configurable keys and 18 LEDs. Up to six Digital Key Module DKM plus can be connected to a Digital Call Station DCS plus. This allows communication stations with up to 120 keys and 120 LEDs.
Notifier Dual Enhanced Loop Interface Board is equipped with microprocessor and will continue to function in case control panel fails.
The Dual Input Module with Output uses three addresses of 99 available module addresses on a loop and responds to regular polls from the control panel reporting its type and the status (open/normal/short) of their supervised device circuits.
Dual Loop Module Kits by Notifier PCB for additional 2 loops, and plug in cable connector with Max. three modules perpanel also Maximum of 512input devices per panelusing standard LIBs.
End-of-line module for the end of the VARIODYN D1 voice alarm system loudspeaker line for standard compliant monitoring, when more than 20 loudspeakers are connected to a line.
End-of-line (EOL) resistors are sold in packs of 10 and are available in 4.7 or 47K Ohm.
Epoxy-encapsulated multi-voltage relays are used for high-current switching applications such as fan and damper assembly control, door control, air handling unit controls, and other types of system interfacing.
Addressable monitor modules suit a variety of applications for intelligent fire alarm control panels (FACPs).
FDM-1(A) dual monitor modules supervise circuits of dry contact input devices, such as conventional heat detectors and pull stations, or monitor and power circuits of 2-wire smoke detectors.
Fire and Fault Relay Expansion Card by Morley-IAS adds fire and fault relay outputs for the HRZ series panels.
FTM-1(A) fire phone control modules with FlashScan® mode only are intended for use with NFS-640, NFS2-640, NFS-3030, and NFS2-3030 control panels. They provide the capability to monitor and control a circuit with up to two firefighter phones.
FW-RM SWIFT® wireless relay modules allow the control panel to switch contacts by code command. The relay contains an isolated set of Form C contacts, which operate as an SPDT switch.
Pluggable Fiber Optic module for the fiber optic switch 583394.11 in 1310 nm multimode. This provide a Fiber Optic cable length up to 2 km.
The Gent Xenex XEN-FFR Fire Fault Relay is designed to either add an additional fire and fault relay or provide a remote fire/fault relay from the main control panel.
FlashScan® dual relay/monitor modules are designed for use with NOTIFIER ONYX® and CLIP Series fire alarm control panels. Each relay output is intended for Form C switching applications, which do not require wiring supervision for the load circuit.
Galaxy Flex+ Output Option Board is available with relay interface
Galaxy Grade 2 Rio Expander are low Priced expanders by Honeywell that provides Up to 128 links for automation.
Audio Interface Module is part of Galaxy® Dimension series of security systems. The alarm receiving centre can listen in using independent audio channels to identify the specific location if the alarm has been triggered and verify source and cause.
Galvanic Isolators are single channel isolated repeater. They are suitable for use as an intrinsically safe isolator between an IST200 translator module and up to a maximum of 15 x 22051EISE intrinsically safe photoelectric smoke sensors.
Hochiki ESP Loop Driver Cards are used as accessory for ZX5e and ZXSe fire alarm control panels.
Honeywell Loop Driver Card is used for Apollo XP95 or Discovery protocol.
Honeywell Loop Driver Card is used for Apollo S90 protocol.
Honeywell panel bus I/O modules consist of a terminal sockets and a removable electronic modules, that allow for the sockets to be mounted and wired before the electronic modules are installed.
I/O remote expansion modules are designed for remote monitoring and control applications that enables end-to-end automation and device-to-enterprise integration.
I300 fault isolator modules are designed for use with Fire-Lite® addressable fire alarm control panels (FACPs) and are intended to protect systems against wire-to-wire short circuits on SLC loops.
IDP addressable dual monitor modules are intended for use in intelligent, 2-wire system Farenhyt™ fire alarm control panels (FACPs).
IDP intelligent addressable monitor modules are intended for use in an intelligent alarm system. Each monitor module is intended to interface between a control panel and normally open contact devices, such as pull stations.
This IO module makes it easy to integrate other wired sensors and devices as needed and connects to the system’s gateway wirelessly via Wi-Fi or Bluetooth®.
ISO-6 six fault isolator modules provide six equivalent circuits that will allow a portion of the communications loop to continue operating when a short circuit occurs on that loop.
Input Output cards by Gent are designed for installation in EN54 Vigilon analogue addressable fire panels and Network node.
Intelligent 10-input monitor modules are designed for use with Honeywell Silent Knight® Series fire alarm control panels. Each monitor module is intended to interface between a control panel and a normally open contact device.
Intelligent alarm system control modules have six relays or circuits that are intended for use in intelligent alarm systems and for switching applications.
Intelligent fault isolator modules are addressable and designed for use with the Honeywell Silent Knight® fire alarm control panels. They act as an automatic switch that opens when the line voltage on the signaling line circuit loop drops below 4V.
Intelligent miniature monitor modules are addressable monitor modules intended for use with the Honeywell Silent Knight® fire alarm control panels. They act as an interface to contact devices, such as water flow switches and pull stations.
Intelligent monitor modules are addressable and designed for use with Silent Knight® Series FACPs. They are intended to function with 2-wire systems, where the individual address of each module is selected using the built-in rotary switches.
Intelligent relay modules are addressable and designed for use with Honeywell Silent Knight® Series fire alarm control panels (FACPs). They allows Silent Knight FACPs to switch discrete contacts through code commands.
Isolated RS232 Module Kit includes PCB for isolated RS232 port for OEM interface, 80 column printer etc. The module uses 1 panel COMMS port.
Isolator module allows to isolate branch or portion of the loop affected by the short circuit from the rest of the system. Each isolator module can support up to 25 items maximum.
LON® compact I/O modules are LonMark® compliant analog and digital input/output modules designed for decentralized, space-saving installation in control cabinets and distributor boxes.
Lite-Connect™ fiber modules allow the MS-9050UD to become a common central station communicator for multiple fire alarm control panels (FACPs).
The Loop Booster provides additional power to an Analog addressable loop in order that a greater number of loop powered warning devices may be connected.
The SMS SENTRI2-LPC is an additional loop card for the SENTRI2 fire alarm control panel.
System Sensor offers a range of M200 series Dual Input or Monitor Modules equipted with two supervised input device circuits for monitoring normally open dry contact alarm of activation devices.
The M201E provides a single output that can be switched when commanded by a fire alarm control panel. In the supervised mode, the M201E supervises the wiring to the load devices.
M221E Input Output Modules provides dual channel monitoring of normally open contact fire alarm and supervisory devices, and also provides single pole changeover contacts for the control of auxiliary devices such as fire shutters.
M500R relay control modules contain two isolated sets of Form C contacts, which operate as a DPDT switch. The modules allow the control panel to switch these contacts on command. No supervision is provided for the notification appliance circuit.
M501 mini monitor modules provide a 2-wire initiating circuit for normally open contact fire alarm and security devices.
Output modules are designed for use with any NOTIFIER protocol fire alarm control panel and provides a monitored single output circuit for use with polarised loads (sounder circuit) which requires a suitable power source for the connected load.
Input and output module by NOTIFIER delivers exceptional flexibility to a NOTIFIER fire detection and alarm system. It enables integration with a host of other building management and emergency systems.
The Notifier M720 Dual Input Interface Monitor Module is an Addressable Fire Alarm Interface Module unit that is specifically designed to be used on Notifier Protocol Fire Alarm Systems.
The MB Secure DUO I/O-Module has the same function as detector groups and control modules. It can be operated at either BUS-2 or BUS-1.
MDF-300 dual monitor modules are intended for use with addressable, 2-wire systems. They provide two independent 2-wire initiating device circuits (IDC) at two separate consecutive addresses.
MDF-300(A) addressable monitor modules supervise a circuit of dry contact input devices, such as conventional heat detectors and pull stations, or monitor and power a circuit of 2-wire smoke detectors.
MF-301 addressable miniature monitor modules can be installed into single-gang junction boxes. They are intended for use in 2-wire systems where the individual address of each module is selected using rotary switches.
MMF-302 interface modules allow addressable panels to interface and monitor 2-wire conventional smoke detectors.
MMF-302 6-zone interface modules provide an interface between the intelligent alarm system and a 2-wire conventional detection zone.
MR Series multi-voltage 4-position DPDT control relays offer 10A contacts, which may be operated by one of four input control voltages.
MR Series multi-voltage DPDT control relays offer 10A contacts, which may be operated by one of four input control voltages.
MR Series multi-voltage single DPDT control relays offer 10A contacts, which may be operated by one of four input control voltages.
MR Series multi-voltage single SPDT control relays offer 10A contacts, which may be operated by one of four input control voltages.
MS-2RB replacement boards are for use with MS-2 fire alarm control panels.
5024RB and 5024UDRB are replacement motherboards for MS-5024 and MS-5024UD fire alarm control panels.
9050UDRB is a replacement board for MS-9050UD fire alarm control panels.
Main Control Cards are part of Vigilon system. It is available with EN and BS version plus 16 and 8 line display.
The mains powered interface units are EN54-4 compliant battery-backed power supplies that can be directly connected to the loop and also have highly flexible interfacing capability.
Morley DXc RMU Module Kit provides an IP interface from panel to AMX graphics package.
Morley ZXse RMU Module Kit provides an IP interface from panels to AMX graphics package.
NRX Radio Input-Output Modules are battery operated RF device designed for use with the NRXI-GATE radio gateway, running on an addressable fire system.
NetAXS-123 boards add two doors to your existing one-door system to facilitate three-door web-based access control.
NetAXS-123 boards add one door to your existing system to facilitate two door web-based access control.
NetAXS-4 PCBs are for web-based NetAXS™ controllers. NetAXS controllers enable users to securely manage their system anywhere there is an internet connection, with no dedicated PC costs.
NetAXS™ input boards provide panels additional inputs.
NetAXS™ output boards provide panels additional outputs.
Non Scanner Relay Processor Module (DRP) is required if remote relays are not used with display.
PRO3200 16 alarm input modules interface with intelligent control modules (PRO32IC), providing 16 supervised alarm inputs and a dedicated power fail and panel tamper when tile mounted.
PRO3200 16 relay output modules interface with the intelligent control module (PRO32IC), providing up to 16 Form C, 12V DC, 2A relay output controls.
The PW Series modular intelligent controller system is an advanced access control hardware architecture that is capable of providing solutions for large enterprises.
Pluggable LonWorks® bus I/O modules consist of a terminal socket and a removable electronic module, allowing the socket to be mounted and wired before installation.
Pluggable panel bus output modules allow you to monitor and control remote points using 2-wire communication with the main controller.
Pluggable panel bus I/O modules communicate via the LonWorks® bus and panel bus respectively.
Input/ output module for Pro-Watch IP based Controler
Input/ output module for Pro-Watch Controler
Pro-Watch® M2000 intelligent controller subpanels work in conjunction with PWM5 intelligent controllers.
Q769 adjustable signal adapters are accessory devices that provide a modulating signal to M7405 and M7415 actuators when used with a controller.
R-14E multi-voltage relays have field-wiring terminal strip connections, mounting tracks, and come with hardware mounted inside of a steel enclosure.
The Notifier RS485 Communication Card kit is used for networking Notifier ID61, ID62, ID2000, ID2002, ID3000 & ID3002 panels to a repeater panel.
The Remote Mount Relay includes blank plates with a remote mounting box.
VESDAnet sockets interface are required when a standard unit is used to provide a flexible solution where permanent mounting is not required in this case VESDAnet sockets connects the HLI onto the VESDAnet network.
Residential silence modules/switches are designed to provide a means to silence signals and speakers that are connected to them for up to 10 minutes during an alarm condition.
Reversing relay and synchronization modules enhance the operation of 2- and 4-wire i³™ Series detectors equipped with a sounder.
SD500 addressable miniature input modules act as an interface to dry contact devices, such as water flow switches and conventional pull stations. Due to their small size, the modules can be mounted in a single-gang junction box.
SD500-AIM addressable input modules are for use with FACPs. SD500-AIM addressable input modules are designed to be used with pull stations, water flow switches, and other applications requiring dry contact alarm initiation devices.
SD500-ANM addressable notification modules provide supervised monitoring of wiring to the load devices that require an external power supply to operate such as bells, horns, and strobes.
SD500-ARM addressable relay modules add two Form C contacts to the Farenhyt™ addressable system.
SD500-LIM line isolator modules can isolate a short circuit wiring fault on a signaling line circuit (SLC) loop.
SD500-LK dual action conversion kits are used to convert the SD500-PS (single action pull station) to a SD500-PSDA (dual action pull station).
SD500-SDM addressable 2-wire smoke detector modules allow IntelliKnight® fire alarm controls to interface and monitor 2-wire conventional smoke detectors.
SK-Control addressable notification modules provide supervised monitoring of wiring to the load devices that require an external power supply to operate such as bells, horns, and strobes.
SK-Control-6 six circuit supervised control modules provide supervised monitoring of wiring to load devices that require an external power supply or amplifier to operate.
SK5280 status display modules provide outputs and control functions for remote annunciation of alarm, trouble, and supervisories for each zone.
The SMS SENTRI4-LPC series are spare / replacement loop cards for use with the SMS SenTRI4 fire alarm control panel.
SWIFT® wireless monitor modules are used to monitor devices with mechanical contact actuation. They come with special covers that have built-in tamper magnets. For best performance use SWIFT® wireless monitor modules with SMB500-WH boxes.
SWIFT® wireless monitor modules are intended for use with wireless gateways to interface with devices having contacts used to signal status conditions.
Scanner Relay Processor Module (DRP) is required if remote relays are not used with display.
Serial and parallel gateway modules allow you to connect virtually any standard PC-compatible printer to a Silent Knight® Series fire alarm control panel (FACP) and to generate reports on site.
Multi-mode and single-mode fiber-optic modules are plug-in fiber loop modules that work as a single channel to transmit or receive communications with Silent Knight® network interface cards.
Sylk™ I/O modules are part of the Spyder® family of products and expand the footprint of a single Spyder device, increasing the controller's ability in situations that require a large amount of physical I/O.
System relay modules provides remote termination card with new software supplied in a remote mounting box and it allows reporting of any alarm or fault condition that appears on a VESDAnet loop regardless of the initiating zone.
The M200 series of modules are a family of microprocessor controlled interface devices permitting the monitoring and/or control of auxiliary devices.
Two relay output dual monitor modules are intended for use with intelligent, 2-wire systems, where the individual address of each module is selected using the built-in rotary decade switches.
UltraKey Lite® keyboards offer industry-leading design for reliable, user-friendly control of video management systems.
V-Plex® single-output relay modules are an accessory for use with ADEMCO control panels that support serial number addressable polling loop output devices.
VESDA VRT-500 is a Remote Mount Relay Module. It is designed for use with VLP, VLS and VLC detectors. The relay module is a 7 relay remote termination card with specialized software.
VESDA VIC Multi-function Control Cards are interface cards for the range of Xtralis VESDA VIC smoke detectors. They expands the range of input and output communications.
The VESDAnet Interface Card provides VESDAnet communication from the detector to other VESDAnet devices including configuration and monitoring tools.
VRT-900 includes blank plates with a remote mounting box and has 12 relay version for VLS.The Remote Box can house a single module with a termination card.
The Vigilion Main Control Cards are a range of cards that are designed for installation in Vigilion panels.
Input/Output Card by Gent is a part of Vigilon System.
Vigilon Loop Card is designed to provide a powerful diagnostic tool and support a higher loop load in alarm by delivering a higher capacity for EN54-23 compliant visual alarms devices.
VisorALARM PLUS receivers manage and receive alarms from burglar and/or fire alarm panels equipped with Teldat MIP or Fire-Lite® IPDACT IP alarm transmission modules.
W-CRF SWIFT® wireless relay modules allow the control panel to switch contacts by code command. The relay contains an isolated set of Form C contacts, which operates as an SPDT switch.
Xtralis Smoke detector is an interface card for the range of Xtralis VESDA VLF smoke detectors. Multi-function Control Card expands the range of input and output communications a VLF detector can perform.
ZNAC-4 notification appliance circuit (NAC) option modules are Class A conversion modules which mount to J3 connectors on the upper right side of the FCPS-24 (field charger/power supply) circuit board.
The Morley 796-181 is 4 line Display Kit used for the Morley ZX5Se fire alarm control panel. This kit includes the Display Plate and Overlay.
The ZX5e Loop driver card is a plug-in card for use in the ZX5e series intelligent multi-protocol fire alarm control panels.
The ZXSe range of analogue addressable fire alarm control panels have been designed and constructed around proven and reliable microprocessor technology.
ZXSe Programmable Output Relay Module consists of 4 relay outputs built on a single printed circuit board. Each output relay provides single pole double throw (SPDT) switching action for other locally powered equipment.
Start your search with category name, product name, part number, etc.
Copyright © 2021 Honeywell International Inc.