Switch and Wiring Loom are designed as spares for SAFE which is introduced as an engineered solution for your building and to avoid the risk of generating multiple false evacuations.
The 3-gang electrical boxes are 5.556 cm deep and intended to be use in semi-flush mount applications.
The 34000 S-Quad adapter base provides a simple and cost effective solution for the replacement of ageing 34000 range sensors with current S-Quad Sensors.
4 trim ring and snap-in mounting clips for IQ8Quad detector base
The 5104RK retrofit kits are designed for use with 5104 fire control communicators.
6500-MMK multi-mounting kits allow 6500 beam smoke detectors to be mounted to ceilings or to walls where the detector and reflector cannot be mounted within 10° of one another. One kit mounts either the transmitter/receiver unit or reflector.
6500-SMK surface-mount kits are intended for use with beam detectors to mount transmitters and receivers when using 6500-MMK multi-mounting kits.
The support plate is designed exclusively for CMSI 8000 rack.
A2402A are Plastic Clamp Set made up of Polyamide/Stainless Steel Dowel available in pack of 100.
ABS-Bögen und Winkel als Zubehör für Ansaugleitungen von Ansaugrauchmeldern.
AP Base Conduit Adaptor are base adapter accessory for B401DG and B401DGR for tubes of 18 and 20mm.
RF-FTX Additional filter accessories are used for HPX-751E HARSH ™ analog addressable aspiration detectors.
Adhesive Foot for Printed Circuit Board.
Plastic Clip for Air Flow Reducers
Cage is designed exclusively for Alertus© Alert beacons.
Angle Brackets by Gent are designed for use in areas where beam detector will not be installed to a vertical surface, or where the beam path is not perpendicular to the installation surface.
Anti Condensation Film is an easy applicable film that provide long time resistance to condensation on the acrylic Emitter lens
Anti-Climb for Tower Column. It provide one for each column.
Anti-Condensation Film is used for OSID-EH housings. An easy applicable film that provide long time resistance to condensation on the glass fronts.
The aspiration reducing film sheets are secured with marking tape to prevent it from becoming displaced.
ISP-104 from Xtralis are aspirator fans for IFT-P, IFT-4 and IFT-6 detectors.
Avoor Din Rail Mounting is suitable for Esserbus alarm unit type 808623, voltage converters type 781337/781336 and fuse module type 382040.
F210 flanged rings are designed for use with B210LP detector bases.
F110 flanges are replacements for the flanges on B400 Series detectors.
BEAMMMK multi-mounting kits allow reflectors and reflected beam detectors to be mounted to either vertical walls or ceilings.
Battery Holder Kit is a Marine System Component designed for Marine battery box.
Beam angle bracket accessories are used for SenTRI beam sensors.
Parallel Bracket is the accessory for mounting the pair of beam sensors.
Gent by Honeywell’s S-Quad Beam Sensors provides an enhanced solution for linear beam detection for applications where point detection is either not practical or economic.
S-Quad Beam Sensors provides an enhanced solution for linear beam detection for applications where point detection is either not practical or economic.
Beam Sensor Transmitter mounted on a base fixed to either bracket allows the detection of smoke over distances from 2 m to 100 m each mounted on a base fixed to either bracket.
Black Detector Kit for 200 Series detectors.
C-Rail Profile Mounting Kits are designed to be mounted inside the housing of the FACP FelxEs control. It is also used to mount a FOC converter in addition to single module housing.
CO detector replacement plate to cover the footprint of previously installed detectors.
CO2 Probes are required for S2401CO2 Detector.
Cable glands are designed for ulti-spectrum UV/Dual IR/VIS fire and flame detectors.
Cavity wall mounting kit for touchscreen operating unit
Ceiling Passive Infrared Detector have 360° coverage, range 16 meters in diameter installed at 3.6 meters in height.
Kit allowing the individual addressing of a manual call point on CMSI SensES type B.
The SENS-RDR utilizes infrared technology to read the sensitivity of i3 and 100 Series conventional detectors.
Custom Films with personalized description sold in packs of 10 and in multiples of 10.
DUCTCOV covers are designed for use with DNR and DNRW duct smoke detectors.
The DST family of sampling tubes are pieces of steel piping with a series of holes drilled the entire length of the tube and should extend the entire width of the duct.
Warranty Extention extends the standard warranty period for DTS evaluation unit.
Deep base gaskets are used for conventional Enscape audible visual sounders.
The ES Detect automatic detector is an intelligent nonaddressable detector specifically designed for operation on conventional detector groups
Detector base with relay contact output, for detector family IQ8Quad FM.
Covers are designed for protecting the detectors against contamination during construction or renovation work.
Detector test magnets simplify detector testing and maintenance
Detector base with relay output for ES Detect 48 V DC operation
Dual Height Clips are an integral part of the mounting accessories.
Single Terminal Back Boxes are used for mounting RTS151 key. Remote annunciator accessories providing reset function and has a Red LED to indicate alarm conditions.
Duct Sampling Kit includes 3 tube mounting plates, compression fittings, adaptors, elbows and reducers for use with XAS2-US, inlet and exhaust tubes and flexible tubing.
Duct Sensor is an accessory designed for the Vigilon System Sensors.
E Series ribbon cable accessories are used for ICAM aspirating smoke detectors.
E Series thermistor cable assemblies are used for ICAM aspirating smoke detectors.
E-CAB2 Container is a Universal metal container for peripheral cards. Ex: it can contain 1 MAB + 1 SCP-50-12 + IND16 + MORS 0 + MORS 1+ IND8. Dimensions: 380 x 265 x 160 mm
The ECO 1000 deep detector bases are used in the ECO1000 series conventional detectors with conventional fire alarm control panels.
ECO 1000/ Apollo protection is used to protect against moisture where the detector is mounted and places where condensation can occur.
The Xtralis VSM4 provide full and comprehensive integration of your VESDA and ICAM smoke and gas detection systems. The VESDA ECO Detector network connection One required per monitored detector.
ECO1000 Series basic bases are intended for connection of ECO1000 series fire detectors to fire and security and fire alarm systems (SCP) control panels using a 2-wire circuit, including a control panel with alternating voltage in the loop.
EMC shield for IQ8Quad, ES Detect detector base
ES Line Switchgear allows the management of the most efficient fire safety technologies. This technology makes it possible to target the few detectors to be changed during visits to maintenance.
The expansion kit is designed to increase the management capacity of the CMSI 8000.
EXT steel exhaust tubes are intended for use with HVAC duct smoke detection and monitoring products.
The Egg Crate Grille is designed so that provision is made for a free area of 94% in order to preserve high level aesthetics whilst also maintaining the integrity of the vent from interference.
The Enclosure box with DIN rail is designed for DIN rail mounted units. The box is well suited where there is a need for mounting DIN rail equipment on the detector loops.
Multi-voltage conventional relays are used for high-current switching applications such as fan and damper assembly control, door control, air handling unit controls, and other types of system interfacing.
Extender poles are designed for use with XR2B detector removal tools, and can extend 5 to 15 ft.
The Xtralis In-Line Filter provides Xtralis customers the ability to address a wide array of harsh environments with high levels of airborne contaminants in a simple and cost-effective manner.
External filter for FAAST with cartridge.
F5000-LRK are long range kit for linear detector consisting of 3 reflectors to form a set of four that is included with the F5000M or F5000S detector.
External Filter by Esser is used in all FAAST Systems
FAALT accessory boxes are used in FAAST LT 200 aspirating smoke detectors modules.
FAAST LT module mounting kits are the optional accessory for the FAAST LT range of aspirating detectors that allows an input or output module to be installed inside the FAAST LT unit.
FAAST LT-200 Models are the advanced fire detection system for use where early warning and very early warning are a required. This models allows early and reliable smoke detection.
Single or Dual Channel Accessories box for FAAST LT-200 Standalone
FP-WHITE faceplates are designed for use with Silent Knight® addressable modules. They better compliment the design aesthetics of a modern building and also match white System Sensor® L-Series AV devices.
White Filter Elements are replacement for the internal filters inside the ICAM IFT, ICAM IAS and ICAM ILS series detectors.
Notifier Fireray Flush Mount Plate comes pre-drilled to mount the FIRERAY 3000 detector head to any flat cable.
Vesda Xtralis 06-HK10 ICAM Baffle for Hochiki (Pack of 10)
The heating Kit allows the reflector of the reflected beam smoke detectors to operate in environments prone to the formation of condensation.
Heating Resistor is an optional element which connects the detector socket to the external power source with 2 WAGO cubes.
Housing is designed for accessories and is a part of the aspirating products range.
ISP-406 is used as a cover removal tool for IAS or ILS
Xstralis ISP-115 are the E Series Cable assembly beacon used with ICAM Flexible Aspirating Smoke Detector.
Xstralis ISP-105 are the Exhaust Silencer used with ICAM Flexible Aspirating Smoke Detector.
Xstralis ISP-123 are the replacement display for IFT-1 ICAM Flexible Aspirating Smoke Detector.
Xtralis ICAM Accessories offers Medium and fine filter elements for the internal filters inside the ICAM IFT, ICAM IAS and ICAM ILS series detectors. Replacement filters elements are available in pack of 10 with Black colour
The IAS/ILS Aspirator is an accessory for ICAM Series.
IFT-6 Replacement display accessories are used for ICAM IFT-6 aspirating smoke detectors.
IFT-P Chassis accessories are used for ICAM IFT-P aspirating smoke detectors.
ISP-114-01 from Xtralis are detector chambers for ICAM IFT-P detector.
IFT-P Fan cable assemblies are used for ICAM IFT-P aspirating smoke detectors.
ILS-1 Display kit accessories are used for ICAM ILS-1 single channel laser aspirating smoke detectors.
ILS-2 Display kit accessories are used for ICAM ILS-2 dual channel laser aspirating smoke detectors.
The base is designed with a heating resistor and is a part of the Addressable Centrals introduced by Esser.
IQ8Wireless technology enables the IQ8Quad automatic fire detectors (with and without alarm signaling units), MCPs and the IQ8Alarm signaling unit to be wirelessly connected to the fire alarm system IQ8Control and FlexES control.
Visual Alarm Diffuser designed for IQ8L range meets the requirements of the labor code and the safety regulations against fire risks in public buildings in terms of welcoming deaf and hard of hearing people.
IQ8MCP Addressable Manual Call Point is equipped with status indicator, membrane, short circuit isolator, transparent protective cover and mounting base.
IQ8Wireless mounting frame for IQ8Quad detectors, white
ICAM FLOW SENS ASSY IAS/ILS
Inertech Pressure Vents are high performance vents which provide 100% efficiency at the pressure of 95.5 Pascals.
Installation adapter for suspended ceilings
Installation/removal tools are designed for use with System Sensor® plug-in smoke detectors. They permit installation and removal of detectors in elevated mounting locations.
The Intelligent Notification Module is an addressable notification module for use with Honeywell Silent Knight series fire alarm control panels (FACPs). It provides supervised monitoring of wiring to load devices
Intelligent Thermal Detectors by Honeywell are thermal detectors with integral communication has features that surpass conventional detectors. Point ID capability allows each detector’s address to be set with decade address switches
SD505 smoke detector bases are designed for use with IntelliKnight® photoelectric smoke detectors.
Intelligent Detector Color Kits are designed for use with NOTIFIER® intelligent detectors.
The Trim Rings are for use with 2351B intelligent detectors and are compatible with B300-6, B300-6-IV, and B210LP 6-inch standard bases.
Intellknight Address Head Removal Kit for an SD505 addressable photoelectric smoke detector.
Internal Filters are designed exclusively for suction systems.
L-Series bezel kits enable installers to easily turn any L-Series fire or plain device into a device that meets ECN/MNS requirements.
VESDA Aspirating Pipe and Fittings are produced in redABS under a stringent quality control system.
Label-smoke detector pipes are manufacture from ABS (Acrylonitrile Butadiene Styrene), very lightweight, versatile material, guaranteeing you easy and professionalinstallation.
Lettering is introduced for sign boards of the series 5500.
Light shield is available for installation in areas where direct sunlight cannot be avoided
Low noise nozzles are designed to discharge the inert gases in a uniform configuration and reduce air turbulence and noise in the enclosure.
Message Sound Diffuser meets the requirements of the labor code and the safety regulations against fire risks in public buildings in terms of welcoming deaf and hard of hearing people.
Mounting Brackets are available in pack of 10.
Multi-voltage conventional relays are used for high-current switching applications such as fans and damper assembly controls, door controls, air handling unit controls, and other types of system interfacing.
Multilingual interface card packs for FAAST XM aspiration detectors.
Multiple mounting support brackets allows the F5000M or F5000S detector to be installed on sloping ceilings or walls with an angle greater than 10º.
NS-GX-ETH Ethernet Interface allows the connection of GALAXY DIMENSION control units to the Enet cpu, via the ETHERNET network.
Non-return valve is designed for use with the FAAST aspiration smoke detection system.
This test filter is intended for use with OSI-R detectors.
OSID wire guards are steel cages designed to protect OSID imagers and emitters from vandalism and accidental damage. The cages are constructed of heavy gauge steel wire with a corrosion-resistant polyester coating.
OSID environmental housings protect OSID imagers and emitters from dust and water ingress in industrial environments. The glazed housings are made of ABS and the glass windows cause minimal attenuation of the UV and IR beams.
Installation kits for OSID detectors include a laser alignment tool, a test filter, a PC cable, a cleaning cloth, and a manual.
This laser alignment tools allow for quick alignment of OSID detectors. They also align and lock the eyeball and activate the emitters when locked.
OSP-003 acrylic test filters are intended for use with OSID detectors.
Bracket for mounting on oblique surfaces of barrier emitters and receivers F3000. They offer 360 degrees of rotation plus 180 degrees of adjustment.
IP 55 outdoor barrier. GEMINI is a mini active infrared barrier, with 2 lenses, with small dimensions. Pre-wired and ready for installation, it consists of a transmitter and a receiver unit with 8 selectable digital frequencies.
SEN-INT-ACDIN Interface is a 240V output interface and it comes with a DIN Rail mounting kit.
P48-21-00 end caps for metal sampling tubes are intended for use with conventional and intelligent duct smoke detectors.
PAN1-PLUS-SC Bracket is a Metal bracket for ceiling and flag mounting for PAN1-PLUS.
PID-95 point identification devices monitor single Style B circuits and are designed to be mounted into electrical backboxes.
Plastic box for multimodal to accommodate up to six standard modules of the M7xx series. Constructed in antistatic ABS, ignition characteristics V0 light cream leaks and transparent cover to display the status LEDs and the address of the modules.
The point detector wired bases are used with smoke and heat fire detectors of the System Sensor PROFI, 100, 400 series when connected to control panels with alternating voltage in the loop.
Magnetic recessed contact for armored doors with 4 output wires (length 30 cm) for contact and anti-tampering, suitable for installation on iron and non-ferrous doors and windows. Container is made of brass.
Red Flashing Light is completed with bracket and wall support.
Backboxes are designed for use with Silent Knight® remote annunciators.
Replacement beacon cover accessories are used for ICAM aspirating smoke detectors.
The Replacement Filter Elements are Medium and fine filter elements for the internal filters inside the ICAM IFT, ICAM IAS and ICAM ILS series detectors.
Replacement air filter pads for 801544
S-Quad accessories is designed exclusively for S-Quad Multi-Sensor and Visual Alarms Device.
S-Quad Mounting Plate is an installation base used for installing S-Quad Multi-Sensor.
Gent S-Quad Sensor Bases are used for all S-Quad Sensors. Available in White or Black.
The System Sensor B524HTR is a specialist base in addition to the traditional low profile or deep bases, designed for use with all System Sensor 200 analogue addressable detectors
Sockel mit integriertem Isolator für den Notifier - Ringbus für Melder der Serie 700
B401 plug-in detector bases are used with System Sensor® conventional S300 smoke and heat detectors. These bases make detectors more versatile than equivalent direct-wired models.
PS-SMBB surface-mount boxes are for use with SD500 pull stations.
Sampling tubes intended for use with SD505 duct smoke detectors.
SD505-RB six inch relay bases add a relay output function to addressable detectors.
SD505-IB Six Inch Isolator Base
SD505-NSRT-RH disassembly tools are designed for Hochiki address sensors.
SMB600 flanged surface mounting kits may be used with certain System Sensor® smoke detectors when flush or recessed mounting are not possible.
ST metal sampling tubes may be installed from the front or back of System Sensor® HVAC duct smoke detection and monitoring products. The tubes lock securely into place and can be removed by releasing the front or rear locking tab.
The STI is an accessories that are been used with STI Stopper II®. The accessories that are been used are conduit gasket and conduit spacer.
The System Sensor SWIFT® Wireless system offers an AV base to support L-Series devices in wireless installations.
Semi-flush fixing kit is designed to mount an S-Quad device. To semi-flush mount a special housing must be used which consists of a main assembly and a trim ring.
SenTRI DIN rail mounting kits are used in SMS SenTRI range of addressable interface modules.
SenTRI metal interface housings are used for single channel SenTRI system interface modules.
The Sensor cable heating testing tool are used to verify functionality of the sensor cable according to regional requirements. Electronic boards control the heating sleeves to simulate a fire condition along the fibre-optic sensor cable.
Series 5500 signboards english fire alarm messages are the "Fire Alarm" message identifications by using LEDs.
Series 9200 Standard Detector Base with zone isolator and terminal for a remote LED indicator.
Visual Alarm Diffuser designed for ceiling mount IQ8L-C meets the requirements of the labor code and the safety regulations against fire risks in public buildings in terms of welcoming deaf and hard of hearing people.
Single Row Blanking Plates are used to fill the enclosure if less sub racks are used than the enclosures maximum.
F36-05-00 air filters are for use with DH400 air duct smoke detectors.
Smokesabre test gas for smoke detectors
The Notifier spare plastic keys are used for test. These are compatible only for P700.
Special Fine Micro filter is designed for use in areas with extreme pollution.
Special clip for aspirating holes 6.5 mm
Standard L-Clips are designed for linear heat detection system. These are equipped with Silicone pads.
The 19 inch rack enclosures are designed to house up to 20 display and programmer modules in a wide variety of configurations to suit the particular requirements of a site where centralised control and monitoring of the VESDA system is required.
System Sensor BEAMSMK are the surface mounting kit for the reflective projected beam smoke detector which are used whenever surface wiring is being used.
Surface Socket is a tube inlet up to 22mm outside diameter.
Top Hat Rail is available in 400mm.
Troubleshooting And Maintenance Tool is used to display a mimic of the bus with the physical addresses, as well as the serial numbers of the remote equipment present.
Xtralis VESDA Wall-Mounted High Level Interface (HLI) links VESDAnet1 with PC software monitoring tools, Building Management Systems (BMSs) and Fire Alarm Control Panels (FACPs).
VESDA Pipe and Fittings are part of an integrated system manufacturedfrom specialty plastics designed for use with most aspirating smoke detectionsystems, the VESDA VLP system in particular
VESDA® VPS100/300 and power supplies are capable of providing operating power, including battery backup, for the entire line of VESDA by Xtralis® aspirating smoke detectors.
VP-CLIP 3/4-inch pipe support clamps are designed for use with VESDA® pipes. They are required for each five foot length of pipe.
Honeywell provides VLI series sample point heads for the 10mm capillary aspiration pipe.
Variable Direction Stand is required for RIV-601P/FA with 230x250x120mm direction.
Pipe – 3⁄4”
Vigilion Beam Sensor Recievers are a part of Vigilon’s loop powered technology which allows 16 beam pairs to be connected to the same loop circuit, each covering a distance of up to 100m.
White detector kit for 200 Series detectors.
The waterproof base are designed for mounting with IQ8Quad and ES Detect detectors. The base has 3 pre-cut entries for M20 cable glands.
Weather Protection For Flame Detectors are accessories designed to protect the detector from rain, snow and high temperatures of solar radiation.
Wet Room Adapters are designed for F-ECO1000 series detectors and are crucial to prevent the risks of fire and to protect homes. The presence of a smoke detector in a home can reduce the risk of a fire by 90%.
Wireless Detector Adapter Base accepts a compatible fire detector to allow wireless fire detection in a Vigilon system.
XAS Sample & Exhaust Tubes comes under Xtralis Accessories. These are available in 18”,36” and 60 “. They also consists of 2,3 and 4 sample and exhaust tube kit.
LF42282 water trap kits are single-zone devices that are for use with XAS-1-US air sampling units and are designed for installations which are subject to high humidity and/or condensation.
LF42285/LF42286 single-zone probe kits are designed for use with XAS-1-US air sampling units. They include a 2-hole sample and exhaust tube kit.
Metric to Imperial Pipe Adaptors, Kit
The System Sensor A77-AB adapter rings allow installers to retrofit i³™ Series detectors where a larger diameter smoke detector was previously installed.
MOD2W maintenance modules allow for communications to 2-wire i³™ Series detectors with any listed fire alarm control panel capable of utilizing this module.
Start your search with category name, product name, part number, etc.
Copyright © 2022 Honeywell International Inc.