Copper Network Cards are used to allow data to pass between control panels in a Vigilon Compact networked fire system.

DIM-485 display interface modules convert EIA-232 to EIA-485 and are for use with Fire-Lite® LCD-40 Series annunciators.

DXc Network card are fitted to each panel in order to create a network and to connect panels together.

The Morley IAS Fire System by Honeywell product 795-122 is a RS232 communication card kit designed for use with the Morley DXc range of analogue addressable fire alarm control panel.

Q7751A Excel 10™ routers double the bus length and the number of usable nodes on a LonWorks® (previously called E-Bus) networks.

External Paging Interface Module supports SCOPE, ASCOM/ TELENOVA and HLSUK paging products. It Requires RS485 card to be fitted in control panel.

Single Mode Fibre Card by Honeywell allows a fast and more reliable network over distances of up to 20km between Vigilon Plus Panels.

Field Bus Interface Plus is used for interfacing for the programming of the FACP 8007, 8000 C/M, 8008, gateway, ABIGA and Extinguishing Control Panels 8010 or for the direct field-side connection of a single installed loop.

The Fire and Smoke Detector Interface module is used with conventional fire and smoke detectors located in hazardous areas.

Galaxy 2 - 44 RS232 Lead

Galaxy Dimension 96 zone control panel with PSTN dialler.

Galaxy Dimension IP Modules are provides alarm signalling and remote servicing support for Galaxy systems via 10 Base T Ethernet LAN/WAN supporting TCP/IP protocol.

Printer Interfaces from galaxy has 26 pin and sub D connector.

A073-00-01 modules are direct mounted RF portal on PCB

The interface can be used to interface transmitter, to drive I/P converter, fire and smoke detectors or similar switched resistor systems, located in Hazardous Area, requiring a wide output current range to operate properly.

The GSM/GPRS module can be used to equip sites with no telephone line (e.g., a second home) and allows remote monitoring to be set on partially or fully unbundled sites with no Internet connection available for the alarm system.

Honeywell Security Galaxy Flex GSM/GPRS Module for Galaxy Flex provides additional communication options for reliable alarm signalling with an alarm receiving centre. It also allows Galaxy’s Remote Servicing Suite (RSS) to access the panel remotely.

WIN-PAK Integrated Security by Honeywell provide enhanced access control functionality for decades, its superior scalability enables users to initially deploy WIN-PAK XE and then easily upgrade to SE or PE editions when their business needs evolve.

Interface card that allows ID3000 control panels to be connected to the ID2net network using fiber or optical cable, recommended for distances greater than 500 meters or for industrial environments.

The IFP-2000 network repeater modules are used when panels to be networked are located further than 20 feet apart or when panels are located in multiple buildings.

IGSMCFP4G commercial fire communications radios offer contact ID reporting with select VISTA® control panels.

IPOTS-COM digital communicators transmit system status (alarms, troubles, AC loss, etc.) to a central station via the public switched telephone network and/or internet protocol.

The IST200 Translator Module are intended to be used with analogue addressable systems in conjunction with System Sensor 22051EISE and 2251EIS intrinsically safe smoke sensors.

IGSMV4G/IGSMVCN4G Internet and GSM communicators are groundbreaking communication solutions that offer full data reporting and uploading/downloading with most Honeywell control panels.

Low Voltage Input /Output Vigilon Interface Module used to control a resistive load of up to 1A at 30Vdc/ac via a set of single pole change over contacts. Also allow the monitoring of the external equipment.

The Loop Powered Current Repeater is dual channel current repeater. It can be used to interface transmitter, I/P converter or fire-smoke detectors to provide input-output isolation.

MODBUS Interface Modules connects to the RS-485 peripheral bus of the ZX series fire alarm control panels and allows panel interrogation by Modbus control system.

The Mains powered interface units are EN54-4 compliant battery backed power supplies that can be directly connected to the Vigilon and Nano loop and also have highly flexible interfacing capability.

The Modbus Protocol Serial Communications Card address and parameter configuration through two 8-selector dip switches. It provides two independent output ports: one RS485 (Half Duplex) and one RS232.

N-485-API-2 communication adapters are for use with N-1000-II control panels.

NPB-8000 expansion modules and kits are for WEB-8000 controllers.

The Notifier NGM PCB plugs is an ID2NET network gate way module for use with the Notifier ID3000 panel range.

Pearl Communication Card Provides third party protocol (RS232 & RS485 ports) for PEARL panels.

Notifier PRL-P2P ID²net network card for pearl panel network.

RPT-E3 ARCNET network repeaters are for use with E3 Series® and S3 Series fire alarm control panels (FACPs). They allow remote subassemblies to connect to broadband networks from remote locations.

RS 232 Communication Modules by Morley-IAS are suitable for modem and leased or private line are used.

RS485 Communication Module supports two-wire RS485 multidrop transmission between networked ZX2Se/ZXSe/ZX5Se control panels

The Safety Bus system allows the Fire and Fire & Gas detection and the firefighting control in a unique bus assuring a high safety level.

Replacement Interface Board on a carrier into a legacy 34440 Mains powered interface unit.

S4 Input Interface modules are used to link the fire alarm system to other plant management devices such as sprinklers and security systems. They can also be used to link to a zone of conventional detectors.

The S4-34418 from Gent is a Keyswitch Interface which comes with a blue enclosure.

SK-NIC network interface cards work with fire alarm control panels (FACPs), allowing FACPs to connect to one another through broadband networks.

SLC-2 expander modules enable a second signaling line circuit (SLC) loop for Fire-Lite® MS-9600 fire alarm control panels (FACPs).

W-SYNC SWIFT® wireless synchronization modules provide audio and visual synchronization between SWIFT® notification appliances and System Sensor® wired notification appliances.

The SenTRI Four analogue addressable fire detection and alarm system offers medium to large sized building owners the latest in system flexibility and control panel aesthetics.

SMS SenTRI Network Card for SenTRI two control panel analogue addressable fire systems.

Multi-mode and single-mode fiber-optic modules are plug-in fiber loop modules that work as a single channel to transmit or receive communications with Silent Knight® network interface cards.

Morley 796-171 is a replacement/spare base PCB/motherboard for the Morley ZX1SE fire alarm control panel.

The Relay Module has unique multi-voltage input from 24 to 230 V UC with colored making.

The Universal Interface Module (UIM) serves as an interface module for the Voice Alarm and Public Address system. It connects two analogue audio inputs, two analogue audio outputs as well as 48 control contacts.

VESDA® VHX-0200 Sliding Windows high level interface (HLI) models enable connections between a VESDAnet™ (a communications protocol that allows devices to communicate on one network) and configuration/monitoring platforms.

VESDA Wall-Mounted Modbus High Level Interface (HLI) links your VESDAnet1 with PC software monitoring tools, Building Management Systems (BMSs) or Fire Alarm Control Panels (FACPs).

Xtralis VESDAnet Socket is a VSR spare module for VESDA sub rack.

VESDA® Modbus type 3 HLIs act as a proxy for all VESDA devices on the VESDAnet™ network, providing access to rich status information available from VESDA detectors, as well as the ability to control and configure these devices.

VIG-NC-FO Network Card features up to 31 Control panels and Network Nodes can be connected in a secure loop

Gent by Honeywell introduces Vigilion's Loop Powered Interfaces and other devices which can accommodate a high quantity of loop powered interface units offering flexible range of inputs and outputs from the FD&A system.

The Vigilion Netwrok Cards are network cards for Vigilion Addressable Fire Detection System that expands the Gent Vigilon Plus and Gent Vigilon fire alarm network

Compact Plus Terminal Node is used for Vigilon panel network. It is supplied in black.

The Vigilon Fibre Optic Secure Domain Cards allow fast message passing to the network. These cards must be plugged into the backplane of the panel or node in a dedicated slot.

The VESDA Sliding Windows High Level Interface (HLI) links your VESDAnet* with PC software monitoring and configuring tools such as Xtralis VSM4 and Xtralis VSC.

ZX range spare parts base PCBs consists of 5 loops and are used for ZXSe intelligent multi-protocol fire alarm control panel.

The ZX series is an intelligent fire alarm control panel. The ZX series simple approach has produced a modular scalable fire alarm platform suitable for protecting all types of premises.

Internal Printer for use with ZX5Se intelligent fire alarm control panel.

The ZXSe range of analogue addressable fire alarm control panels have been designed and constructed around proven and reliable microprocessor technology.