Sensor Accessories
The 10103 3-gang electrical boxes are 5.556 cm deep and intended to be use in semi-flush mount applications.
119640B Cabinet Lock
B501 bases are four-inch flangeless mounting bases designed for use with System Sensor® 200 Series detectors. They are intended for use with intelligent systems that have screw terminals for power (+ and -) and remote annunciator connections.
TR300 trim rings are for use with 2351B intelligent detectors and are compatible with B300-6, B300-6-IV, and B210LP 6-inch standard bases.
2D51A photoelectronic detectors use state-of-the-art optical sensing chambers and are designed to provide protection in duct applications when installed with InnovairFlex™ 4-wire duct smoke detector housings.
The 5104RK retrofit kits are designed for use with 5104 fire control communicators.
6500-MMK multi-mounting kits allow 6500 beam smoke detectors to be mounted to ceilings or to walls where the detector and reflector cannot be mounted within 10° of one another. One kit mounts either the transmitter/receiver unit or reflector.
6500-SMK surface-mount kits are intended for use with beam detectors to mount transmitters and receivers when using 6500-MMK multi-mounting kits.
7617M/U compression fittings are brass 1/2-inch NPT fittings for use with T6031 bulbs.
7628 end-of-line resistors are 4.7K ohm resistors that must be used with polarized devices for proper operation.
7641B end-of-line resistor/diode assemblies are required when connecting the fire alarm control panel (FACP) to releasing solenoids. They allow the FACP to supervise the wiring between its notification appliance circuits and the releasing solenoid.
F-A3384-000 air filters are replacement filters for 8000 Series detectors. These filters combine a 30 micron filter element and a plastic housing into a single module that reduces service time and labor.
B110LP detector bases are designed for use with System Sensor® models 2151 photoelectronic and 1151 ionization detector heads. These 2-wire bases are equipped with screw terminals for power, ground, and an optional remote annunciator.
B112LP detector bases are designed for use with System Sensor® models 2151 photoelectronic and 1151 ionization detector heads. These 4-wire bases are equipped with screw terminals for power, ground, and an optional remote annunciator.
B114LP bases are for use with System Sensor® photoelectronic and ionization detector heads. They are intended for use in 4-wire systems with terminals provided for remote annunciator and relay connections.
B116LP bases are plug-in bases for use with System Sensor® ionization detector heads and System Sensor photoelectronic detector heads.
F210 flanged rings are designed for use with B210LP detector bases.
B210LP mounting bases are six-inch, flanged bases for use with 200 Series detectors.
B224BI isolator detector bases prevent an entire communications loop from being disabled when a short circuit occurs.
B224RB relay bases are designed for use with 200 Series detectors, and provide a single Form C contact relay for the control of auxiliary functions, such as door closures and elevator recall.
B300-6 bases are six-inch, standard flanged, low-profile mounting bases for use with 200 Series detectors.
F110 flanges are replacements for the flanges on B400 Series detectors.
B401 plug-in detector bases are used with System Sensor® smoke and heat detectors. These bases make detectors more versatile than equivalent direct-wired models.
BEAMMMK multi-mounting kits allow reflectors and reflected beam detectors to be mounted to either vertical walls or ceilings.
BG12TR trim rings are designed for semi-flush mounting applications, and intended for use with BG-12 Series fire alarm pull stations.
BEAMLRK long-range kits are designed for use with System Sensor® reflective projected beam smoke detectors and allow installation between 230 to 380 ft (70 to 100 m) apart.
CO detector replacement plates are designed to upgrade previously installed detectors that are competitors to the CO1224 CO detectors.
F36-09-11 air filters are intended for use with DH100/200 duct smoke detectors.
F36-05-00 air filters are for use with DH400ACDC duct smoke detectors.
DH400OE-1 all-weather enclosures are specifically designed to house and protect System Sensor© model DH400ACDCIHT high temperature duct detectors from the elements.
DUCTCOV covers are designed for use with DNR and DNRW duct smoke detectors.
DST metal sampling tubes may be installed from the front or back of System Sensor® HVAC duct smoke detection and monitoring products. The tubes lock securely into place and can be removed by releasing the front or rear locking tab.
DT8300-FMK flush mounting kits are designed for use with DT8320 Series DUAL TEC® motion sensors.
ELR-47K End-of-Line Relay
CPVC socket unions are used in combination with other System Sensor® CPVC pipe fittings and related accessories to complete pipe networks in Fire Alarm Aspiration Sensing Technology® (FAAST) systems.
FP-WHITE faceplates are designed for use with Silent Knight® addressable modules. They better compliment the design aesthetics of a modern building and also match white System Sensor® L-Series AV devices.
The 17007 hex key is a 9/64 key that is intended to unlock hex-locking pull stations.
SMB10 universal swivel-mount brackets are designed for use with SC100 and SC105 seismic vibration sensors.
SD505 smoke detector bases are designed for use with IntelliKnight® photoelectric smoke detectors.
CK300 color kits are designed for use with NOTIFIER® intelligent detectors.
T55-127-010 removal tools are for use with Fire-Lite® intelligent detectors. The extender pole is not included with T55-127-010 tools.
L-Series bezel kits enable installers to easily turn any L-Series fire or plain device into a device that meets ECN/MNS requirements.
23165 trim rings are for use with LCD-40 Series remote annunciators.
HNMSEB hard drive trays are for use with MAXPRO® NVR SE Series video surveillance systems.
OSP-004 test filters are intended for use with OSI-R detectors.
OSP-002 laser alignment tools allow for quick alignment of OSID detectors. They also align and lock the eyeball and activate the emitters when locked.
P76 Series Dry Pressure Sensors duct probe accessory.
The 32003169-001 duct pick-ups are for use with P7640A pressure sensors.
Backbox weatherproof gaskets are replacement gaskets for use with PSWPB backboxes.
PWT-BV bypass valve manifolds are designed for use with PWT wet differential pressure sensors.
XR2 installation/removal tools are designed for use with System Sensor® plug-in smoke detectors. They permit installation and removal of detectors in elevated mounting locations.
REL-47K End-of-Line Resistor
122427 backboxes are designed for use with Silent Knight® remote annunciators.
SC111 day and night movable mounting kits are designed for use with SC100, SC105, and SC115 detectors. They provide extra protection to safe doors and prevent arming while doors are unprotected (can allow arming in night position only).
SC113 internal test transmitters are designed for use with SC100 and SC105 sensors to allow for regularly testing. Mounting hardware is included with the SC113.
SC115 external test transmitters allow for the simultaneous testing of all SC100 sensors installed within a five meter radius of the transmitter. They are compatible with most panels offering remote test functions.
PS-SMBB surface-mount boxes are for use with SD500 pull stations.
Sampling tubes intended for use with SD505 duct smoke detectors.
SD505-RB six inch relay bases add a relay output function to addressable detectors.
SD505-6SB sounder bases are six inches and add an audible output function to the IntelliKnight® SD505-APS, SD505-AIS, or SD505-AHS addressable detectors.
SD505-IB six inch isolator bases isolate short circuit wiring faults on a Class A (Style 7) and Class B (Style 4) SLC loops. Normally if FACPs detect a short on the SLC loop, the entire loop can be disabled.
SD505-NSRT-RH disassembly tools are designed for Hochiki address sensors.
SMB500 surface-mounting boxes may be used with certain System Sensor® modules when flush or recessed mounting are not possible.
SMB600 flanged surface mounting kits may be used with certain System Sensor® smoke detectors when flush or recessed mounting are not possible.
Replacement dust covers are for use with System Sensor® 100/200 Series smoke detectors.
HEXW hex wrenches are for use with OSY2 and PIBV2 supervisory switches.
System Sensor BEAMSMK are the surface mounting kit for the reflective projected beam smoke detector which are used whenever surface wiring is being used.
T55-118-00 keys are for use with System Sensor® remote test stations.
TR29 wall-mount enclosures can be used to wall-mount any 1/4-inch or 3/8-inch diameter probe sensor.
The System Sensor WFD Series vane-type waterflow detector, with a computer designed paddle, fits Schedule 10 through Schedule 40 steel pipe sizes 2 in through 8in. The design of this unit makes it easy to install and simple to maintain.
Velociti® Series B200S sounder bases set a new standard for performance, installation, and aesthetics. They are addressable sounder bases that require a unique, separate sounder base address.
WFDW hex wrenches lock WFD, EPS, OSY2, PIBV2, and PSP1 Series detectors.
A77-01-02 replacement terminal block kits are for use with WFD Series water flow detectors.
XP-4 extender poles are designed for use with XR2B detector removal tools, and can extend 5 to 15 ft.
A77-AB adapter rings allow installers to retrofit i³™ Series detectors where a larger diameter detector was previously installed.
RT removal tools are installation and removal tools for use with i³™ Series detectors.
Start your search with category name, product name, part number, etc.
