Expansion modules for TONN8/HAWK 8000

Single Mode Fibre Card by Honeywell allows a fast and more reliable network over distances of up to 20km between Vigilon Plus Panels.

Field Bus Interface Plus is used for interfacing for the programming of the FACP 8007, 8000 C/M, 8008, gateway, ABIGA and Extinguishing Control Panels 8010 or for the direct field-side connection of a single installed loop.

These S4 Single Output Interfaces are designed for use with any Vigilon/34000 fire alarm control panel. Each module includes loop isolators for device isolation.

The S4 Single Output Interfaces are suitable for mains switching, they provide normally closed and normally open contacts rated at 13A 250Vac (nominal 230Vac) resistive load.

Galaxy Dimension 96 zone control panel with PSTN dialler.

Galaxy Dimension IP Modules are provides alarm signalling and remote servicing support for Galaxy systems via 10 Base T Ethernet LAN/WAN supporting TCP/IP protocol.

Printer Interfaces from galaxy has 26 pin and sub D connector.

A073-00-01 modules are direct mounted RF portal on PCB

Gent Connection PCB for FAAST Interface (FAAST LT)

The GSM/GPRS module can be used to equip sites with no telephone line (e.g., a second home) and allows remote monitoring to be set on partially or fully unbundled sites with no Internet connection available for the alarm system.

Honeywell Security Galaxy Flex GSM/GPRS Module for Galaxy Flex provides additional communication options for reliable alarm signalling with an alarm receiving centre. It also allows Galaxy’s Remote Servicing Suite (RSS) to access the panel remotely.

Interface card that allows ID3000 control panels to be connected to the ID2net network using fiber or optical cable, recommended for distances greater than 500 meters or for industrial environments.

The IST200 Translator Module are intended to be used with analogue addressable systems in conjunction with System Sensor 22051EISE and 2251EIS intrinsically safe smoke sensors.

Low Voltage Input /Output Vigilon Interface Module used to control a resistive load of up to 1A at 30Vdc/ac via a set of single pole change over contacts. Also allow the monitoring of the external equipment.

The PW Series are RS232/M-Bus converters which act as master interfaces for M-Bus networks with 3/20/60 slaves

The Mains powered interface units are EN54-4 compliant battery backed power supplies that can be directly connected to the Vigilon and Nano loop and also have highly flexible interfacing capability.

Vigilon NPORT 100 - RS232 to IP device (single unit 2 required per link)

Spare master control board for SenTRI 4 control panel

Notifier Pearl Smart Watch Kit. Provides an IP interface from your panel to your AMX graphics package.

RS232/M-Bus Converters act as master interfaces for M-Bus networks with 20 slaves. They also have a ZVEI port for optical isolation. They are of a compact design.

The PW Series are RS232/M-Bus converters which act as master interfaces for M-Bus networks with 3/20/60 slaves. They also have a ZVEI port for optical isolation.

Pearl Communication Card Provides third party protocol (RS232 & RS485 ports) for PEARL panels.

Notifier PRL-P2P ID²net network card for pearl panel network.

RTU02 Routing Termination Units are Use on the Fire Routing output on the system IO card interface to allow full monitoring of the transmission path when using third party transmission devices

Replacement Interface Board on a carrier into a legacy 34440 Mains powered interface unit.

Replacement Card for Mains Powered Interface (34440)

S4 Input Interface modules are used to link the fire alarm system to other plant management devices such as sprinklers and security systems. They can also be used to link to a zone of conventional detectors.

S4 Interface Modules 4-Input / Output Interface Module are designed for use with Vigilon and 34000 fire alarm control panel

The S4-34418 from Gent is a Keyswitch Interface which comes with a blue enclosure.

SMS SenTRI Network Card for SenTRI two control panel analogue addressable fire systems.

Spare PCB for Vigilon ASD Interface

The Universal Interface Module (UIM) serves as an interface module for the Voice Alarm and Public Address system. It connects two analogue audio inputs, two analogue audio outputs as well as 48 control contacts.

Upgrade from Parallel Port Dongle to USB. Note: Old dongle must be returned within 20 Days or full charge for a new dongle will be made

VESDA Wall-Mounted Modbus High Level Interface (HLI) links your VESDAnet1 with PC software monitoring tools, Building Management Systems (BMSs) or Fire Alarm Control Panels (FACPs).

VESDA® Modbus type 3 HLIs act as a proxy for all VESDA devices on the VESDAnet™ network, providing access to rich status information available from VESDA detectors, as well as the ability to control and configure these devices.

VESDA® VHX-0200 Sliding Windows high level interface (HLI) models enable connections between a VESDAnet™ (a communications protocol that allows devices to communicate on one network) and configuration/monitoring platforms.

VIG-NC-FO Network Card features up to 31 Control panels and Network Nodes can be connected in a secure loop

Gent by Honeywell introduces Vigilion's Loop Powered Interfaces and other devices which can accommodate a high quantity of loop powered interface units offering flexible range of inputs and outputs from the FD&A system.

The Vigilon Fibre Optic Secure Domain Cards allow fast message passing to the network. These cards must be plugged into the backplane of the panel or node in a dedicated slot.

The Vigilon Netwrok Cards are network cards for Vigilon Addressable Fire Detection System that expands the Gent Vigilon Plus and Gent Vigilon fire alarm network

Internal Printer for use with ZX5Se intelligent fire alarm control panel.

The ZXSe range of analogue addressable fire alarm control panels have been designed and constructed around proven and reliable microprocessor technology.