Designed for simple installation and operation, 301C controllers continuously monitor and control toxic gases, combustible gases. and oxygen hazards.

302 Series rate-anticipation heat detectors operate within a controlled range of two to three degrees of their setpoints, regardless of the rate of temperature rise. These detectors are available in either 135 °F (57.2 °C) or 194 °F (90 °C) ratings.

The E969 encoder’s four “Hot Keys” reduce complicated warning command scenarios to a simple two button procedure. A built-in time clock provides for “time of day” and “noon test” activation.

SPKDRV are a Speaker Driver of 400 Watt.

4XZM zone relay modules provide four Form C relay contacts to fire alarm control panels (FACPs).

4X™F transmitter modules provide output for local energy municipal box transmitters, and alarm and trouble reverse polarity circuits. The modules include a disable switch and disable trouble LED.

5600 Series mechanical heat detectors offer property protection against fire and are intended for non-life-safety installations where smoke detectors are inappropriate.

The 6500-LRK is long range of reflection kit for conventional and addressable Reflected Type Projected Beam Smoke Detector.

6500-MMK multi-mounting kits allow 6500 beam smoke detectors to be mounted to ceilings or to walls where the detector and reflector cannot be mounted within 10° of one another.

6500-SMK surface-mount kits are intended for use with beam detectors to mount transmitters and receivers when using 6500-MMK multi-mounting kits.

7556

The Honeywell 7626-25HC is an AlarmNet 25’ RF antenna coax cable which allows you to mount your AlarmNet GSM-ANT3DB external weatherproof antenna up to 25’ from your cellular or dual path AlarmNet alarm monitoring communicator.

The 7720P programmer or the Web-Based Program is used to enter all central-station information. This is saved to the IPGSM-COM communicator panel memory.

F-A3384-000 air filters are replacement filters for 8000 Series detectors. These filters combine a 30 micron filter element and a plastic housing into a single module that reduces service time and labor.

8100 smoke detectors deliver a highly accurate and a very early warning for Fire Detection. They also have extensive communications capabilities to provide maximum control over challenging environments

The ACPS-610(E) is an auxiliary power supply with a battery charging option and a host of special features.

Key lock door for recessed mount is an accessory for emergency telephone stations.

AFAWS Series accessories for emergency telephone stations include backboxes, latching and locking doors, and break glass inserts.

Spare Components & Misc are backup audio cable used to connect the AA P6 to backup AA P4

ANN-MBRLY mounting brackets are for use with NOTIFIER® NFW2-100 fire alarm control panel (FACP) applications.

The ANN-80 annunciator is a compact, backlit, 80-character LCD fire annunciator that mimics the Fire Alarm Control Panel (FACP) display provides system status indicators for AC Power, Alarm, Trouble, Supervisory, and Alarm Silenced conditions

AP-P adapter plates are decorative plastic adapters for mounting 302 Series detectors to four-inch outlet boxes.

Expand the versatility of the InnovairFlex™ line of duct smoke detectors with System Sensor notification and test accessories.

Auxilary power supplys by Notifier are used for the operation of peripheral devices for the ONYX Series control panels.

The ASWP Weatherproof Horn Strobes consists of 24 V, square horn strobes for use with a WPBB R Weatherproof Back Box in outdoor and extreme environment applications. The Weatherproof Horn Strobes are wall mount device.

Accessories for Vesda

Option to Convert the Activation Controls to Fsk Format.

Adapter cable for Scorpion control unit 805540 for operation with quick charger 805543

Adapter for telescopic rod 060426

RF-FTX Additional filter accessories are used for HPX-751E HARSH ™ analog addressable aspiration detectors.

Addressable Photoelectric Detector by Notifier is use for state-of-the-art photoelectric sensing chamber with communications to provide open area protection.

AirSCan IRF9 Sensor by Honeywell Analytics is a range of Infrared diffusion-based gas detection that enables thermal stability and freedom from vibration. The IRF9 satisfies AB32 California code and is CARB compliant.

Aluminum outdoor column loudspeakers are a high-performance, public address column loudspeaker for outdoor use. They offer a broad frequency response range, low distortion, and a high sound pressure level.

Annunciator Key Switches provide access security for the control switches on the LCD-160. Key-switch kit includes key, hardware, and an annunciator label.

Anti Condensation Film is an easy applicable film that provide long time resistance to condensation on the acrylic Emitter lens

Anti-Condensation Film is used for OSID-EH housings. An easy applicable film that provide long time resistance to condensation on the glass fronts.

Aspirated Gas Detection for Micro Bore ASD System (VESDA-E VEA Addressable Aspirating Smoke Detection) and When used with the VESDA-E VEA.

Auxiliary Board has limited function contact closure activation control.

B110LP detector bases are designed for use with System Sensor® models 2151 photoelectronic and 1151 ionization detector heads. These 2-wire bases are equipped with screw terminals for power, ground, and an optional remote annunciator.

B112LP detector bases are designed for use with System Sensor® models 2151 photoelectronic and 1151 ionization detector heads. These 4-wire bases are equipped with screw terminals for power, ground, and an optional remote annunciator.

B501 bases are four-inch flangeless mounting bases designed for use with Notifier SWIFT Wireless detector . They are intended for use with intelligent systems that have screw terminals for power (+ and -) and remote annunciator connections.

BEAMLRK long-range kits are designed for use with System Sensor® reflective projected beam smoke detectors and allow installation between 230 to 380 ft (70 to 100 m) apart.

BEAMMMK multi-mounting kits allow reflectors and reflected beam detectors to be mounted to either vertical walls or ceilings.

The Backbox for Programmable Universal Zone Coder(UZC-256) is used when the UZC will not fit in panel enclosure.

Backboxes are for use with fire alarm control panels (FACPs) and are used to mount up to two batteries and power supplies.

Battery Interconnect Cables are connects Battery from + to -.

Battery Positive Wire connects Battery + TO MPS-24B

Blank Module Dress Plate used to cover annunciator positions or panel positions and also mounts some option modules.

CAC-4 Class A converters are for use with Gamewell-FCI® Flex 404 4-zone fire alarm control panels (FACPs).

CAT 30 Lock with Key

CB-1 Chassis Bridge provides a bridge between CHS series chassis.

CB500 wiring barriers are used to separate power-limited and nonpower-limited wiring inside of junction boxes.

Spare Components & Misc are power harness cable used to connect the 5000 CPU to MPS

CELL-MOD cellular fire alarm communicators provide cellular communication as an alternate method of central station reporting. These models house the GSM communicator in a plastic enclosure and has an option for an external antenna.

Battery charger circuit board and mounting chassis are designed for use with fire alarm control panels (FACPs).

CHS-4L chassis are for use with NOTIFIER® fire alarm control panels (FACPs). They are low-profile, 4-position chassis and mount two AA-30 amplifiers.

CM4 Toxic Gas Monitor

CO detector replacement plate to cover the footprint of previously installed detectors.

CO1224T carbon monoxide (CO) detectors with Real Test® use a highly accurate and reliable electrochemical sensing cell to provide an early warning of dangerous CO levels.

CO2 Replacement Cartridges for VESDA ECO Ex Gas Detector.

Spare Components & Misc are transponder power ribbon cable used to connect XPP to option module

Cascade Cable's for connect AMG P10 to AMG-E P10

Ceiling Loudspeaker is a cost-competitive ceiling loudspeaker which has an excellent audio performance and aesthetic appealing enclosure. This full range loudspeaker features a high sound pressure level and a wide frequency response range.

Cellular Fire Alarm Communicators provide cellular communication as an alternate method of central station reporting. These models include a GSM communicator within a metal cabinet enclosure with lock/key, and includes an external antenna.

The 301EM-20 acts as a controller for up to 20 remote sensors and suits a variety of gas detection system solutions for Mechanical Rooms.

The SENS-RDR utilizes infrared technology to read the sensitivity of i3 and 100 Series conventional detectors.

The ECO1005 thermal detector belongs to System Sensor’s ECO1000 range of detectors. ECO1000 is a range of conventional detectors produce latest manufacturing technology and supplied with an array of advanced features, making them ‘better by design’.

DHE - series from Notifies is a range of Door Holder Extension Rods for the DH24120 Series Electromagnetic Door Holders. The DH – Series provides a wide range of Door Holder Extension Rods with various lengths and Multiple finished.

DH24120 electromagnetic fire door holders are available in various mounting styles and finishes.

DHCPD

M200-DIN is a Rail Bracket used with M700 series Module. The M700 Series module is designed for use protocol fire alarm control panel and include selectable loop isolation in every device.

DP-2 dead front dress panels are for use with Fire-Lite® 411UDAC fire alarm control panels (FACPs). They restrict access to the system wiring but allow access to the membrane switch panel.

DP-51050 dress panels are for use with Fire-Lite® MS-5UD/MS-10UD Series fire alarm control panels (FACPs). They restrict access to the system wiring but allow access to the membrane switch panel.

Black and White detector kits for 200 Series detectors.

Detector test magnets simplify detector testing and maintenance

Detector parallel display

Detector removal tool

Detectors for all NOTIFIER detectors and third party detectors

Display modules provide real-time indication of the status of a VESDA detector. They have a 20-segment vertical bar graph display, a 2 digit numeric display, an audible sounder, clear alarm and fault indicators.

External dust filters for Midas gas detector are used to protect the tubing from contamination.This End of line particulate filter are used for normal gases .

Gamewell’s DH Series of electromagnetic fire door holder back boxes are constructed of durable die-cast metal finished in high-lustre double chrome or brass plating.

Gamewell-FCI’s DH Series of electromagnetic fire door holder catch plates are constructed of durable die-cast metal, finished in high-luster, double chrome or brass plating.

Door Holder Swivel Base Mounting for Use with Gamewell-FCI’s DH Series of electromagnetic fire door holders.

Dual Gas Cartridges by Xtralis are to introduce ECO, the industry’s first system to combine ASD with gas detection and environmental monitoring.

Single Terminal Back Boxes are used for mounting RTS151 key. Remote annunciator accessories providing reset function and has a Red LED to indicate alarm conditions.

The Duct Mounting Kits provides installation of sensors directly into ducts with diameters from 3 to 16in.

E3Point by Notifier is a range of Toxic/combustible gas monitor that makes a commercial operation run more intelligently to protect people, property and the bottom line.

Gas cartridge assemblies intended for use in E3Point gas sensors.

E³Point Accessories offers ECLAB Splash Guard Enclosures.

The Vesda Eco provides early warning of toxic, oxygen and flammable gas hazards to protect personnel and property ensuring business continuity.

The Eco gas detector provides early warning of toxic, oxygen and flammable gas hazards to protect personnel and property ensuring business continuity. They uses an existing aspirating pipe network to actively monitor for gas escapes and build-ups.

The Vesda Eco provides early warning of toxic, oxygen and flammable gas hazards to protect personnel and property ensuring business continuity.

ECO™ replacement sensor cartridge accessories are used for vesda Eco detectors.

The Vesda Eco provides early warning of toxic, oxygen and flammable gas hazards to protect personnel and property ensuring business continuity. Vesda Eco uses an existing new aspirating pipe network to actively monitor for gas escapes and build-ups.

Xtralis, the industy’s first combined aspirated smoke and gas detection system. It provides early warning of toxic, oxygen and flammable gas hazards to protect personnel and property while ensuring business continuity.

ECO1000 conventional relay bases are for use with System Sensor® ECO1000 series sensor heads and are designed to operate in both 2- and 4-wire systems, with screw terminals provided for power connections and remote annunciator.

System Sensor’s ECO1000 range of detectors have been produced using the latest in manufacturing technology, supplied with an array of advanced feature.

System Sensor Bases that are intended for use with ECO1000 Series detectors.

The ECO1002 multi-criteria detector uses a state-of-the-art optical chamber and a thermal element combined with a microprocessor, running sophisticated algorithms to provide quick and accurate detection of fires.

The ECO1005 A detector is a rate of rise sensor, which uses a state of the art thermal element combined with an application specific integrated circuit (ASIC)to provide quick and accurate detection of fires.

ECO1003 optical smoke sensors use state-of-the-art optical chambers combined with application-specific integrated circuits (ASIC) to provide quick and accurate detection of fires.

The Alerton ESD-100 is an Ethernet data line protector, which protects equipment connected to unshielded twisted pair (UTP) Ethernet networks from transient voltage.

The Electromagnetic Door Holders are constructed of durable die-cast metal finished in high-lustre double chrome.

Use an End-of-Line device with control panel releasing circuits.

Multi-voltage conventional relays are used for high-current switching applications such as fan and damper assembly control, door control, air handling unit controls, and other types of system interfacing.

End-of-line (EOL) resistors are sold in packs of 10 and are available in 4.7 or 47K Ohm.

Explosion-Proof Speaker are designed for potentially explosive atmospheres and harsh industrial and marine environments

CPVC socket unions are used in combination with other System Sensor® CPVC pipe fittings and related accessories to complete pipe networks in Fire Alarm Aspiration Sensing Technology® (FAAST) systems.

FAAST Automatic Purging Unit provides a fully integrated and compact solution with user-selectable preventative or event triggered purging programs.

FAAST XT Aspirating Smoke Detectors are highly accurate Early Warning Fire Detection over a wide coverage area and offer extensive communication capabilities.

FAAST XS aspirating smoke detectors delivers highly accurate Very Early Warning Fire Detection for the smaller applications and offers extensive communication capabilities.

FCM-1 intelligent addressable control module provides supervised monitoring of wiring to load devices that require an external power supply to operate, such as solenoids, sounders, strobes, or bells.

The FCM-1-REL Releasing Control Modules are specifically designed for fire suppression releasing applications in FlashScan® systems. Power to the release agent solenoid(s) runs through the module for full-time monitoring and supervision.

Remote power supplies/battery chargers FCPS-24 are compact, cost-effective, 6- or 8-amp remote power supplies with battery chargers.

FlashScan® dual relay/monitor modules are designed for use with NOTIFIER ONYX® and CLIP Series fire alarm control panels. Each relay output is intended for Form C switching applications, which do not require wiring supervision for the load circuit.

FM Series electromagnetic door holders are designed for virtually any remote door release application. They are primarily used to hold fire and smoke barrier doors open until released by a remote smoke detector or other switching device.

FM Series electromagnetic door holder by Fire-Lite are designed for virtually any remote door release application. They are primarily used to hold fire and smoke barrier doors open until released by a remote smoke detector or other switching device.

FM-Series electromagnetic door holder spacers are used, when necessary, for the installation of remote door release systems.

FM Series electromagnetic door holders are designed for virtually any remote door release application. They are primarily used to hold fire and smoke barrier doors open until released by a remote smoke detector or other switching device.

FMM-4-20 Analog Input Module allows the NFS2-3030 fire alarm control panel (FACP) to monitor industry-standard, linear-scale, 4–20 mA protocol sensors.

Honeywell's FireLite Alarms Firefighter Phone Jacks are used to mount to a single-gang electrical box. All circuits are power-limited and supervised.

FS20X Flame Detector

FS24X Flame Detector

FSB-200 single-ended reflector-type addressable beam smoke detectors are for protecting open areas with high and sloping ceilings, and wide-open areas, where spot-type smoke detectors are difficult to install and maintain.

FSK Format converter module converts the Siren Activation Controls to FSK Format

Photoelectric Smoke Detector is unique optical sensing chamber is engineered to sense smoke produced by a wide range of combustion sources. Intelligent (addressable) detectors include point ID capability.

FSP-851(A) Series intelligent plug-in smoke detectors with integral communication provide features that surpass conventional detectors.

FSX™ fire and flame detectors sense the WideBand IR™ radiant energy of blackbody particulate and molecular emissions generated by both hydrocarbon and nonhydrocarbon flames and fires.

FT Series filter elements are used in ICAM IFT, ICAM IAS and ICAM ILS series detectors.

FTM-1(A) fire phone control modules with FlashScan® mode only are intended for use with NFS-640, NFS2-640, NFS-3030, and NFS2-3030 control panels. They provide the capability to monitor and control a circuit with up to two firefighter phones.

The Relay Module provides 8 DPDT relays for the indirect activation of fans, louvers, etc. at programmable alarm levels.

The Notifier ISO-X(A) Fault Isolator Module is used with Notifier Onyx and CLIP series Fire Alarm Control Panels (FACPs) to protect the system against wire-to-wire short circuits on the SLC loops.

Filter Cartridge Assembly

The trim rings are designed for semi-flush mounting applications, and intended for use with BG-12 Series fire alarm pull stations.

Fire Alarm Storage Cabinets by Notifier are solution to meet the demanding code standards required today & Its primary goal is to manufacture code compliant solutions and this product allows you to do just that.

Fire detector protective cover helps prevent malicious or accidental false fire alarms. This unique device has helped prevent false fire alarms around the world for decades.

Fire Protection Housing

Fire-Lite® MBT1 municipal box transponder modules are used between a local energy municipal box and a fire alarm control panel.

Fire-Watch 411 Series digital alarm communicator transmitter (DACT) handheld programmers are digital devices used to locally program NOTIFIER® 411 Series DACTs.

Notifier’s firmware upgradations are used for LIB-200A or LIB-200/400 panels.

The FireLite Four Position SPDT Relay suited for applications where local contacts are required for system status, remote contacts for control of electrical loads, and general purpose switching.

GSM-ANT3DB weatherproof remote antennas optimize transmissions with field diversity technology. The antennas have a versatile, weatherproof design that is suitable for indoor or outdoor applications.

The HAZWP Model Fire Alarm Pull Station is specifically designed for harsh industrial environments where weatherproofing and corrosion are issues.

HP400UL Series power-limited supplies/chargers convert 115V AC/60 Hz input into a power-limited 12V DC or 24V DC output at 4A.

HP600UL Series power-limited supplies/chargers convert 115V AC/60 Hz input into a power-limited 12V DC or 24V DC output at 6A.

Notification Appliance Circuit (NAC) expanders/power supplies are designed to extend the power capabilities of existing NACs (to support ADA requirements and NAC synchronization) and provide power for auxiliary devices.

HPTCOVER transformer enclosures are used in applications where the installation requires a plug-in transformer to be securely affixed to an AC wall outlet.

The Hardware Interface is used for universal zone coder.

Sampling Hole Clips are designed to alleviate such potential issues, by providing a clear, visual indication of sampling point location and its associated hole size.

Heavy-duty re-entrant loud speaker is available with wide-angle horn. Mounting bracket is included for vertical, horizontal or stacked installations.

Speaker & Rotor of High Power Sirens provide an economical alternative for powerful siren communication without compromising quality.

High-Speed Network Communication Modules provides high speed data communications.

Honeywell Cabinate

X-NRI/EN Network Resource Interfaces are universal interface of X-618 for external control access and audio extension. It is suitable to the needs of central interfaces management required by middle-to-large applications.

Gas Controller And Networkable Sensors With Auto-Diagnostic Capabilities, Robust And Reliable Communication, Acts As A Controller For Up To 20 Remote Sensors And Suits A Variety Of Gas Detection System Solutions For Mechanical Rooms

Whelen’s HORNET Series of all hazard sirens provide an economical alternative for replacing outdated electro-mechanical sirens. The HINTRU is Intrusion alarm available with two-way only.

VESDA ECO Ex provides early warning of flammable gas hazards to protect personnel and property whilst ensuring business continuity.

The Notifier’s IPCHSKIT is a IP Communicator Chassis Mounting Kit. For mounting an IPDACT-2/2UD onto the panel chassis or CHS-4 series chassis. Use IPENC for external mounting applications.

IP internet and GSM dual path communicators offer contact ID reporting that operate in conjunction with any fire alarm control panel (FACP) that has a built-in dialer.

IPDACT serial programming cables can transfer data in a snap and have DB9/RJ45 ports for instant connectivity.

IPDACT Series Mounting bracket kits are for use with NOTIFIER® IPDACT Series IP communicators. The kits consist of screws and battery shield with standoffs.

IPSPLT splitters allow connection of both panel dialer outputs to one cable input to the internet protocol digital alarm communicators/transmitters (IPDACT).

ISO-6 six fault isolator modules provide six equivalent circuits that will allow a portion of the communications loop to continue operating when a short circuit occurs on that loop.

Whelen's IPS Series Products delivers clear, powerful tone and voice warnings, eliminating confusion at the onset of an emergency.

2D51 duct smoke detectors are low-profile photoelectric detectors designed for special applications, specifically for use in no-flow or low-flow air-handling systems (0 to 4,000 FPM).

InnovairFlex™ 4-wire photoelectric duct smoke detectors offer 2 sensors to 1 powerboard capability in standard (D4120) and watertight (D4120W) versions.

InnovairFlex™ 2-wire photoelectric duct smoke detectors sense airflow at speeds ranging from 100 to 4,000 ft/min.

The InnovairFlex™ Series are the only duct smoke detectors flexible enough to fit configurations from square to rectangular and everything in between.

InnovairFlex™ duct smoke detectors combine an impressive collection of innovations designed to save you time and money and provide the flexibility you need in the field.

Inspection Manager is a mobile inspection application, paired with a central web-based portal, that makes fire/life-safety system inspection, testing, commissioning and compliance reporting more efficient and cost-effective.

Installation/removal tools are designed for use with System Sensor® plug-in smoke detectors. They permit installation and removal of detectors in elevated mounting locations.

IntelliQuadTM Multicriteria Detectors by Honeywell are advanced detectors with four unique sensing elements to convey accurate fire sensing information.

IntelliQuad™ PLUS advanced fire and carbon monoxide detectors are multi-criteria, plug-in, addressable devices that provide both fire and carbon monoxide (CO) detection.

The NFS-320 intelligent Fire Alarm Control Panel is part of the ONYX® Series of Fire Alarm Controls from notifire.using NFS-320C, an optional ACM Series annunciator can be mounted in the same cabinet.

The Trim Rings are for use with 2351B intelligent detectors and are compatible with B300-6, B300-6-IV, and B210LP 6-inch standard bases.

FST-851 Series Intelligent Plug-in Thermal Detectors by Notifier with integral communication has features that surpass conventional detectors.

VA2BATT are accessories for an Internal battery and charger for VA2000 series.

Intevio extension keypads are for use with remote call stations. Models available with four function buttons/LED indicators, and eight function buttons/LED indicators.

Intrusion Alarm by Whelen is a 2-way Intrusion Alarm

KILLARK® XAL-53 explosion-proof pull stations are suitable for use in hazardous areas due to the presence of flammable gases or vapors, combustible dust, or easily ignitable fibers.

L-PBM20A bi-directional projection loudspeakers are high-performance, 20W public address speakers. They offer a broad frequency response range, low distortion, and a high sound pressure level.

L-PCP ceiling loudspeakers are powerful ceiling mounted speakers. They are specially designed for environments, such as shops, supermarkets, educational institutes, offices, sports fields, hotels, restaurants, and wet environments.

L-PWP public address cabinet loudspeakers are intended for use in general indoor and outdoor applications.

L-Series universal expander plates cut costs and speed installation on emergency communications applications that require fire and emergency warnings by combining the functions of multiple devices on a single mounting plate and backbox.

The LED Array Series Indoor Displays are LED message centers designed for light industrial, commercial, and office use. They quickly display large amounts of information in eight colors and three rainbow effects.

The 4XLM LED Interface Module supports the RZA-4X remote annunciator module.

LM2-PCP06x modular ceiling loudspeakers are 6W economic speakers.

LM2-MHA metal brackets are designed for use with the LM2-PCP06x modular ceiling loudspeaker family.

Li-ion Tamer OEM Board

Lithium pack for FDKM 2100 R and FDKM 2100 B

Lock Kit contains 5 locks and 5 keys.

Audio Cable is low level audio cable for AA-100 and AA-120

MCP3A Indoor Call Point range gives you installation efficiency, flexibility and full compliance with the latest standards.

MNS Indoor Display's are LED message centers designed for light industrial, commercial and office use

Power Cables are of 6-wire which connects ICA to MPS.

MR Series multi-voltage DPDT control relays offer 10A contacts, which may be operated by one of four input control voltages.

MR Series multi-voltage single DPDT control relays offer 10A contacts, which may be operated by one of four input control voltages.

MR Series multi-voltage single SPDT control relays offer 10A contacts, which may be operated by one of four input control voltages.

The Media Interface Board mounts “piggyback” onto the SIB-NET module. Provides full signal regeneration and amplification. For use with NOTI-FIRE-NET Networks.

The MegaDot Display offers message clarity from a 200 ft. (61 m) distance allowing you to visually connect with your employees or customers. the MegaDot uses 10.2cm tall characters for dazzling, moving colour messages you know everyone will notice

The DST family of sampling tubes are pieces of steel piping with a series of holes drilled the entire length of the tube and should extend the entire width of the duct.

Midas® Gas Detector

Modbus Gateway by Notifier provides a communication link between networks that use the Modbus/TCP communication protocol and Fire Alarm Control Panels (FACPs) resident on an NFN network.

Mounting Bracket is used for under cabinet or vehicle mounting.

Multi-module cabinets and chassis support up to 6 multi-module boards:

Multi-Spectrum™ SS4 electro-optical fire detectors are fast reacting, digital, configurable, computerized “smart” units.

Multi-Spectrum™ SS2 electro-optical fire detectors provide ultra-high speed responses to explosive fires and feature programming to assure ultra-high speed millisecond response.

Multi-voltage conventional relays are used for high-current switching applications such as fans and damper assembly controls, door controls, air handling unit controls, and other types of system interfacing.

The N-ANN-Series provides a comprehensive line of annunciators, relay and driver modules to interface with a compatible fire alarm control panel.

The Intelligent Thermal detectors are addressable sensors that use a state-of-the-art thermistor sensing circuit for fast response. These sensors provide open area protection and are intended for use with Fire Warden Series and Spartan.

Replacement door used for mounting ACPS-610 (E) in a CAB-PS1 cabinet when replacing ACPS-2406

The NOTIFIER Oynx University training syllabus enables technicians to become proficient in the design, engineering and commissioning of the Notifier system.

The Notifier NAM-232 Network Adapter Module functions as an interface between the AFP-200, AFP-300, and AFP-400 Fire Alarm Control Panels and the NOTI•FIRE•NET™. The network supports communications over a twisted-pair wire or fiber-optic medium.

Noise Control Modules are used to reduce the common noise for example, noise that is present on both conductors on the Signaling Line Circuit (SLC).

Notifier Addressable Multi Sensor Detector is an intelligent, low-profile detector designed for use with FireWarden Series Fire Alarm Control Panels.

NOTIFIER’s FS-OSI-RI intelligent addressable reflector-type linear optical beam smoke detector is uniquely suited for protecting large open areas with high ceilings, where spot-type smoke detectors are difficult to install and maintain.

The Notifier relay modules provides 10 programmable form-C relays when used with a compatible FACP (Fire Alarm Control Panel).

The Notifier XP6-R six-relay control modules provides a fire alarm system with six Form-C relays. It intelligent, addressable multiple input and output modules are a convenient space saving platform and allow for additional mounting options.

The BRKG-B Breakglass Insert Includes a tempered glass plate, a hammer attached to a chain, and a screw to attach the hammer to the trim ring.

NOTIFIER’s XP6-MA six-zone interface module provides an interface between the intelligent alarm system and a two-wire conventional detection zone.

OSE-RBA spare alkaline battery packs are intended for use with the open-area smoke imaging detection (OSID) devices.

OSID beam detector FTDI cables allow connection of a PC with OSID diagnostic software to the imager.

OSID environmental housings protect OSID imagers and emitters from dust and water ingress in industrial environments. The glazed housings are made of ABS and the glass windows cause minimal attenuation of the UV and IR beams.

OSID environmental housings protect OSID imagers and emitters from dust and water ingress in industrial environments. The glazed housings are made of ABS and the glass windows cause minimal attenuation of the UV and IR beams.

Installation kits for OSID detectors include a laser alignment tool, a test filter, a PC cable, a cleaning cloth, and a manual.

OSY2 supervisory switches are used to monitor the open position of an outside screw and yoke type gate valve.

Omni-Alert siren includes amplifiers, controller box with power supply and battery charger.

HPP31076 Optional Class A (Style Z) are optional adapters to connect four Class A (Style Z) NAC circuits.

BB-XP is an Optional cabinet for one or two modules.

Oxygen Replacement Sensor by Xtralis contains an ECO cartridge which has been calibrated to detect Oxygen (O2) ranging between 0-25% VOL. It is used as a deficiency and enrichment alarm.

P40-KITB Mounting Assembly includes chassis, hinged dress plate, two BMP-1 blank plates, and mounting hardware.

PAM multi-voltage relay modules are ideal for applications where remote relays are required for control or status feedback.

Paging Interface helps interfacing Whelen tones with existing in-plant systems.

Paging Interface to Interface with category Whelen Tones with Existing In-Plant Systems

Paging Interface helps interfacing Whelen tones with existing paging systems.

Photoelectric Smoke and Thermal Detector are addressable, low-profile plug-in photoelectric detectors use a state-of-the-art photoelectric sensing chamber with communications.

Intelligent Plug-In smoke Detectors with integral communication provide features that surpass conventional detectors & these Detector sensitivity can be programmed in the control panel software.

Spare Components & Misc bell power cable used to connect the AVPS P3 to ICM J5 ON XPC

Power Supervision Ribbon connects from MPS P3 to EFB-1 P1.

Power-Limited Supply/Charger convert 115V AC/60 Hz input into a power-limited 12V DC or 24V DC output at 2.5A.

The Notifier 75554 is a laptop to NUP port programming cable. This device connects the NFN Web Server to an NCM-W/F.

Push-to-talk-Microphone

Pyrotector 30-2056B IR flame detectors are compact, unitized packages containing an IR detection cell, solid state electronics, and dry Form C (SPDT) contacts for alarm and fault conditions.

The Pyrotector Model 30-2021-24 and Model 30-2021E-24Ultraviolet (UV) Flame Detectors are highly sensitive to the ultraviolet radiation given off by all types of flames, including those produced by flammable liquids and gases.

RK-MCU INTEVIO master control units are the central management device of the INTEVIO PA/VA system, which is used to manage and monitor all devices and perform various operations.

The RP-2001 is a six-zone fire alarm control panel for single and dual hazard deluge and preaction applications.

The RP-2002 is a six-zone fire alarm control panel for single and dual hazard agent releasing applications.

Reversing relay and synchronization modules enhance the operation of 2- and 4-wire i³™ Series detectors equipped with a sounder.

The RS 485 Connector Cable is available for MNS-Control

The Remote annunciator mounts on a standard single gang box, and provide LED indication of the same functions as the 4XZM zone relay module.

Re-entrant Loud Speakers are 15 watt with multi-tapped, line matching transformers for output adjustment. They are ideal for recessed mounting applications. They include mounting bracket for vertical or horizontal installation.

Refrigerant Gas Sensor is a discreet design and rugged ABS-Polycarbonate housing for the 301IRFS set the standard for the source gas detection in a chiller room.

The FRM-1 Relay Control Module is intended for use in intelligent, two-wire systems where the individual address of each module is selected using the built-in rotary switches.

Remote annunciators are designed for both conventional and intelligent applications. Their red LED provides visual indication of an alarm condition.

Remote Display Module is designed for use with the Laser compact range and it provides real-time indication of the status of a VESDA detector.

The Remote Telephone Zone Module that allows for secure access to the NFC-50/100(E) Notifier First Command Center via cell phone or a remote telephone means.

Replacement Transformer for FCPS-24S6 and FCPS-24S8.

Replacement Transformer Assembly

B401 plug-in detector bases are used with System Sensor® conventional S300 smoke and heat detectors. These bases make detectors more versatile than equivalent direct-wired models.

SB-I/O surface-mount backboxes are for use with Silent Knight® PS-SA and PS-DA pull stations.

SB-10 surface backboxes are for use with Fire-Lite® BG-12LR agent release stations.

The SFP-10UD, 10-zone control panel with built-in communicators, provide reliable fire signaling protection for small to medium-sized applications.

Two Zone conventional fire alarm control panel.

Four Zone conventional fire alarm control panel.

The SFP-5UD, 5-zone control panel with built-in communicators, provide reliable fire signaling protection for small to medium-sized applications.

SMB600 flanged surface mounting kits may be used with certain System Sensor® smoke detectors when flush or recessed mounting are not possible.

SOLO 101 Extension Pole for detectors has a 1.3m length for SOLO-100 rod.

SOLO Mains Heat Tester has a voltage rating of 220V-240V. Compatible to SOLO 814 model.

SOLO Series black colour Carrying Bag is semi-rigid material transport bag to house all the elements of the SOLO series. Used with SOLO 811, 812, 814, 822 and 823 detector testing kits.

SOLO Smoke Detector Test starter Kit of 6m includes one 4.5m SOLO fibreglass telescopic extension pole and one SOLO 330 aerosol smoke dispenser.

SOLO Telescopic Access Pole is extends from 1.26m to 4.5m in 4 sections allowing access to detectors fitted up to 6m.

SOLO Telescopic Fibreglass Pole is extends upto 1.13m in 4 sections allowing access to detectors fitted up to 6m.

SOLO Universal Detector Removal Tool is faced with a vast array of different models shapes and sizes the professional needs a universal tool.

The Notifier SP-4 features four messages Fire, Weather, Announcement and Evacuate.

SP-2B MNS Announcement Evacuate sign is slim 2-1/2 deep box is made of steel, is painted white and is designed for surface mounting. The messages are printed in clear within a black box on clear film.

SPM Flex

SSM Series alarm bells are low-current, high-decibel notification appliances for use in fire and burglary systems or other signaling applications.

STH-15S supervised, horn loudspeakers provide superior intelligibility and dispersion to achieve maximum sound projection and penetration for indoor and outdoor life safety and mass notification applications

The STI is an accessories that are been used with STI Stopper II®. The accessories that are been used are conduit gasket and conduit spacer.

Sampling Hole Clip delivers reliable and accurate sampling hole sizes that are fast to install and easy to locate and identify.

Scorpion Control Unit is a portable test device that connects to the access point and can acid the test from a handheld device.

Scorpion Control Unit Panel SCORP 8000

Scorpion smoke detector test head SCORP 1001

Seismic Mounting and Bracket Kit

B501 bases are four-inch flangeless mounting bases designed for use with System Sensor® 200 Series detectors. They are intended for use with intelligent systems that have screw terminals for power (+ and -) and remote annunciator connections.

The Mounting Base is required to meet local code and application requirements and for that System Sensor offers standard 4in and 6in bases.

System Sensor Select Series detector color kits offer expanded color options to meet varying aesthetic applications.

Accessories and Spare parts for the Sensepoint XCD family

Sensepoint XCD RTD

XCD Sensors and Transmitters supplied separately

Common accessories and spares for the Sensepoint, Sensepoint XCD, Sensepoint XRL, Series 3000, OELD and RAEGuard 2

Bluetooth-Enabled Aesthetic Gas Detector

Sensepoint XCL are fixed point gas leak detectors that are designed to meet the needs of commercial and light industrial applications. They are perfect solution for CO and NO2 detection.

Replacement sensors for the Sensepoint XCL and Sensepoint XRL families of gas detectors

The N-ANN-S/PG Interface module connects either a serial or parallel printer with a compatible Fire Alarm Control Panel (FACP) to print real-time logs of system events, detector status reports, and event histories.

Smokesabre (SABRE01) is a smoke aerosol for quick, low-cost, functional testing of smoke detectors with a simple wrist set.

F36-05-00 air filters are for use with DH400 air duct smoke detectors.

Socketline Flex Serial Socket Outlets are available with black coding plug for installation in cavity walls including fire-proof back box and preassembled cable whip.

A universal remover that fits the same extension rods used for detector testing.

Spare Components & Misc are ribbon cable used to connect DIA to 1010 Display

Spare Components & Misc are battery interconnect cable used to connect the batteries in series

Spare Components & Misc are power supervision to connect the MPS P3 TO CPU

The VORTEX’s rugged power amplifiers and speaker drivers, designed for outdoor warning and harsh environments, deliver powerful siren alerting without the problems associated with motor driven systems.

WPS4004 Series High-Power Voice and Siren Systems deliver clear, powerful voice and siren communication.

WPS4003 Series High-Power Voice and Siren Systems deliver clear, powerful voice and siren communication.

SpectrAlert® Advance HR-LF Selectable-Output Low Frequency Sounders are red, two-wire, 12/24V, low frequency sounders for wall or ceiling installation.

SpectrAlert® outdoor selectable output speaker strobes provide a broad frequency response range, low harmonic distortion, and maintain a high sound pressure level at all tap settings to provide accurate broadcast of evacuation messages.

Status Indicator is introduced under the control options by Whelen.

Surface backboxes are for use with Fire-Lite® BG-12LR agent release stations.

System Sensor BEAMSMK are the surface mounting kit for the reflective projected beam smoke detector which are used whenever surface wiring is being used.

Notifier's System Record Documents (SRD) Cabinet is the perfect solution to comply with the demanding code standards required today. This cabinet is constructed of durable 16 gauge steel with a solid piano hinge and key lock.

Trim Ring for PDRP-1002/PDRP-1002E available in black colour.

The Notifier Acclimate Plus detector is an intelligent, addressable, multi-sensing, low-profile detector designed for use with Notifier Notifier Onyx and CLIP series Fire Alarm Control Panels (FACPs).

Honeywell’s Touchpoint™ plus controllers bring a whole new control experience to your small system of gas detectors. Its modular approach enables you to take control and configure what you need for a wide range of applications.

The UL/CSA Aluminum 3 wire Junction Box Assemblies are optional accessories that can be used for remote sensor mounting.

Unidirectional projection loudspeakers are high-performance, 10W or 20W public address speakers.

Universal digital alarm communicator transmitters are designed for use with NOTIFIER® fire alarm control panels (including legacy panels). These transmitters can be installed in the panel cabinet or remotely in a separate enclosure.

The Universal Zone Coder provides up to 256 different coded outputs. The UZC-256 requires programming software and a hardware PC interface.

Universal adapter for NOTIFIER fire alarm panels

Universal detector filler and detector tester

Universal detector filler and smoke detector tester

Universal detector finder and detector tester, suitable for all detectors (except IRX-751 CTEM)

The VESDA VLC detector has been specifically designed to provide all the benefits of aspirating smoke detection including very early warning in single environment small areas and where space is a premium.

VESDA Sensepoints XCL are Micro Bore ASD System gas detectors come complete with the main detector unit (pre- installed with sensor cartridge), two cable glands, calibration/flow cap, flexible tube and tube clips to connect to VEA tubing.

VESDA Sensepoint XCL Micro Bore provides early warning of the presence of gases for occupant protection and system monitoring whilst at the same time ensuring protection against fire threats.

VESDA Sensepoint XCL Replacement Filter

Replacement Sensor for VESDA Sensepoint XCL Detectors.

XCL-XRL-SC-H2 is a VESDA Sensepoint XCL/XRL replacement gas sensor for hydrogen gas.

VESDA-E FRT COVER VEA-040-A00