Asia Pacific
Europe
Middle East
North America
005883 relay interface boards provide 10 general purpose Form C relays that can be used to control any device that requires a dry contact closure.
The printer is used with the Gamewell-FCI fire alarm control panels (FACPs) and provides printer capability to produce a written record of system events and status changes.
302 Series rate-anticipation heat detectors operate within a controlled range of two to three degrees of their setpoints, regardless of the rate of temperature rise. These detectors are available in either 135 °F (57.2 °C) or 194 °F (90 °C) ratings.
5820 Firefighter Key
5820XL LED I/O driver modules provide an effective means to customize your remote annunciation. They provide LED annunciation and control inputs for the fire alarm control panel (FACP).
005860T surface-mount trim rings are for use with Silent Knight® 5860 remote annunciators. Red and gray options are available.
5865-3 and 5865-4 LED annunciators provide 30 programmable LEDs (15 red, 15 yellow) for maximum flexibility with the Honeywell Silent Knight® Series fire alarm control panel (FACP).
AP-P adapter plates are decorative plastic adapters for mounting 302 Series detectors to four-inch outlet boxes.
B200S Intelligent Sounder Bases set a new standard for performance, installation, and aesthetics. They are addressable sounder bases that require a unique, separate sounder base address.
F210 flanged rings are designed for use with B210LP detector bases.
B224BI Plug-in Isolator Detector Bases prevent an entire communications loop from being disabled when a short circuit occurs.
B224RB Detector Relay Bases are designed for use with 200 Series detectors, and provide a single Form C contact relay for the control of auxiliary functions, such as door closures and elevator recall.
F110 flanges are replacements for the flanges on B400 Series detectors.
BAT Series batteries are Power-Sonic brand batteries. BAT series (or Power-Sonic brand) batteries are recommended for secondary power or backup power for all NOTIFIER® fire alarm control equipment.
Heating kits for use to prevent condensation with the BEAM1224 conventional beam smoke detectors. They lessen the likelihood of condensation by maintaining the unit at a temperature that is slightly higher than the surrounding air.
BEAMLRK long-range kits are designed for use with System Sensor® reflective projected beam smoke detectors and allow installation between 230 to 380 ft (70 to 100 m) apart.
BEAMMMK multi-mounting kits allow reflectors and reflected beam detectors to be mounted to either vertical walls or ceilings.
Backboxes are for use with fire alarm control panels (FACPs) and are used to mount up to two batteries and power supplies.
CB500 wiring barriers are used to separate power-limited and nonpower-limited wiring inside of junction boxes.
The System Sensor DH400OE-1 is a steel enclosure for mounting a standard indoor rated duct smoke detector outdoors.
Detector test magnets simplify detector testing and maintenance
Single Terminal Back Boxes are used for mounting RTS151 key. Remote annunciator accessories providing reset function and has a Red LED to indicate alarm conditions.
The Alerton ESD-100 is an Ethernet data line protector, which protects equipment connected to unshielded twisted pair (UTP) Ethernet networks from transient voltage.
FFT-24 expander boards allow an additional 24 zones to Silent Knight® fire fighters telephone control systems.
FFT-FPJ firefighter phone jacks provide a quick connect to the SK-FFT fire fighter telephone system using an FFT-RHS remote handset.
FHSC firefighter handset cabinets are available in recessed and surface-mount configurations.
FM-Series electromagnetic door holder spacers are used, when necessary, for the installation of remote door release systems.
The trim rings are designed for semi-flush mounting applications, and intended for use with BG-12 Series fire alarm pull stations.
The FFT-STSS and FFT-STSR are compatible with the Fire Fighters Telephone communication system. The FFT-STSS is a surface mount door with keylock. The FFT-STSR is a`recessed mount door with keylock
FFT-HSC Firefighter handset cabinets can hold up to 10 remote handsets.
IDP-ACB module cabinets are for use with Silent Knight® IDP-Zone-6 interface modules. They have a built-in chassis that will accommodate one or two modules.
The Notifier’s IPCHSKIT is a IP Communicator Chassis Mounting Kit. For mounting an IPDACT-2/2UD onto the panel chassis or CHS-4 series chassis. Use IPENC for external mounting applications.
IPDACT serial programming cables can transfer data in a snap and have DB9/RJ45 ports for instant connectivity.
IPDACT Series Mounting bracket kits are for use with NOTIFIER® IPDACT Series IP communicators. The kits consist of screws and battery shield with standoffs.
IPSPLT splitters allow connection of both panel dialer outputs to one cable input to the internet protocol digital alarm communicators/transmitters (IPDACT).
ISO-6 six fault isolator modules provide six equivalent circuits that will allow a portion of the communications loop to continue operating when a short circuit occurs on that loop.
InnovairFlex™ duct smoke detectors combine an impressive collection of innovations designed to save you time and money and provide the flexibility you need in the field.
