Asia Pacific
Europe
Middle East
North America
25mm Red ABS Self Draining Water Trap
25mm/10mm Compression Adaptor Tee comes under accessories of pipes and fittings. This is used for 2 capillary tubes.
4 trim ring and snap-in mounting clips for IQ8Quad detector base
6500-MMK multi-mounting kits allow 6500 beam smoke detectors to be mounted to ceilings or to walls where the detector and reflector cannot be mounted within 10° of one another.
6500-SMK surface-mount kits are intended for use with beam detectors to mount transmitters and receivers when using 6500-MMK multi-mounting kits.
800 Series (EOL) End of line box is used for 800 series Digital Linear Heat Detection (LHD) cable. The LHDC is installed in conjunction with an end-of-line (EOL) device for continuity monitoring.
ABS elbows and brackets for aspirating smoke detectors
ABS Rohre mit einer Lieferlänge von 3m und einem Außendurchmesser von 25mm
AP-P adapter plates are decorative plastic adapters for mounting 302 Series detectors to four-inch outlet boxes.
ASD ADPTR 25MM ABS TO 22MM COPPER
ASD FLUSH SPL PT KIT
RF-FTX Additional filter accessories are used for HPX-751E HARSH ™ analog addressable aspiration detectors.
Window filters for ADPRO PRO E-series.
The Air shield is use for powder applications Which protects FS10 fire Detector window lens from powder build-up.
Anchor plates are the counterparts to door holding magnets in hold-open devices and are mounted on the door leaf.
Angle Brackets by Gent are designed for use in areas where beam detector will not be installed to a vertical surface, or where the beam path is not perpendicular to the installation surface.
Anti Condensation Film is an easy applicable film that provide long time resistance to condensation on the acrylic Emitter lens
Anti-Condensation Film is used for OSID-EH housings. An easy applicable film that provide long time resistance to condensation on the glass fronts.
Apollo Detector Discovery Baffles are used to direct the sampled airflow through the point detectors housed in the ICAM IAS aspirating smoke detector.
ISP-104 from Xtralis are aspirator fans for IFT-P, IFT-4 and IFT-6 detectors.
B210W is detector base used for wireless detectors. It includes a built-in magnet so that wireless devices can establish installed and tampered states.
Heating kits for use to prevent condensation with the BEAM1224 conventional beam smoke detectors. They lessen the likelihood of condensation by maintaining the unit at a temperature that is slightly higher than the surrounding air.
BEAMMMK multi-mounting kits allow reflectors and reflected beam detectors to be mounted to either vertical walls or ceilings.
Baffles are used to direct the sampled airflow through the point detectors housed in the ICAM IAS aspirating smoke detector. Baffle are used for Gent S-Quad S4-710OH, S4-911 02HCO, S4-901 02HCO and comes in 10 Pack.
Batt Filter PCB/Cable For Vig1-72
Battery Holder Kit is a Marine System Component designed for Marine battery box.
Battery LEAD Pack For VIG1-72
Gent by Honeywell’s S-Quad Beam Sensors provides an enhanced solution for linear beam detection for applications where point detection is either not practical or economic.
S-Quad Beam Sensors provides an enhanced solution for linear beam detection for applications where point detection is either not practical or economic.
Beam Sensor Transmitter mounted on a base fixed to either bracket allows the detection of smoke over distances from 2 m to 100 m each mounted on a base fixed to either bracket.
The Blanking Baffle is used with ICAM IAS aspirating smoke detector.
NCA/640-2-KIT is a Bracket installation kit required to mount NCA-2 to the CPU2-640/-640E’s standard chassis.The NCA-2 can be used as a primary display for the NFS2-640 by using NCA/640-2-KIT for directly connecting their network ports
SBC S-Bus coupler for manual / emergency operating level is PLC / DDC systems and component
The Vesda Xtralis CPVC is a Pipe Cutter with Upto 1.5”. Vesda piping systems are produced from specialty thermoplastics that offer unique benefits
Accessories for easier installation of the LRMX linear smoke detector and reflectors on walls, girders, ceilings and beams.
Certification set is introduced for FlexES rack assembly.
Replacement Main Control PCB for Compact Plus Control Panel
Conical Sampling Point Kit (c/w 2m of 10mm OD tube, Trunk adaptor, Point & Decal)
DT8300-FMK flush mounting kits are designed for use with DT8320 Series DUAL TEC® motion sensors.
The ES Detect automatic detector is an intelligent nonaddressable detector specifically designed for operation on conventional detector groups
Detector Lens is designed exclusively for Recessed Mount PIR Motion Detector.
Single Terminal Back Boxes are used for mounting RTS151 key. Remote annunciator accessories providing reset function and has a Red LED to indicate alarm conditions.
EMC shield for IQ8Quad, ES Detect detector base
Use an End-of-Line device with control panel releasing circuits.
Ex barrier for intrinsically safe detectors Series IQ8Quad Ex (i) and 9100
Extension pole
FSX™ fire and flame detectors sense the WideBand IR™ radiant energy of blackbody particulate and molecular emissions generated by both hydrocarbon and nonhydrocarbon flames and fires.
VESDA RESTRICTOR FLOW PK10
Flush Sampling Point Kit (c/w 2m of 10mm OD tube, Trunk adaptor, Point and decal)
High Profile Enclosure is designed with DIN Rail.
Housing for Ex barrier
Housing surface mount, gray
ISP-406 is used as a cover removal tool for IAS or ILS
SMB10 universal swivel-mount brackets are designed for use with SC100 and SC105 seismic vibration sensors.
Xtralis ICAM Accessories offers Medium and fine filter elements for the internal filters inside the ICAM IFT, ICAM IAS and ICAM ILS series detectors. Replacement filters elements are available in pack of 10 with Black colour
Xstralis ISP-107 are the TCP/IP Rabbit Processor Module used with ICAM Flexible Aspirating Smoke Detector.
ISP-114-01 from Xtralis are detector chambers for ICAM IFT-P detector.
IP 43 moisture-proof sm base
IQ8Alarm Plus IP base
IQ8Quad IP42 Protections provides protection to the IQ8Quad detector base against dust and humidity.
IQ8Wireless mounting frame for IQ8Quad detectors, white
IQ8Wireless mounting frames for IQ8Alarm / IQ8Alarm Plus, red and white
ICAM FLOW SENS ASSY IAS/ILS
Inline flow restrictor assembly used for refrigerated storage sampling kit. The Xtralis refrigerated storage sampling kit provides a standardised method of smoke sampling for Refrigerated Storage facilities.
Installation/removal tools are designed for use with System Sensor® plug-in smoke detectors. They permit installation and removal of detectors in elevated mounting locations.
Isolation and assembly base for safety Ex barrier
L-Series bezel kits enable installers to easily turn any L-Series fire or plain device into a device that meets ECN/MNS requirements.
VESDA Aspirating Pipe and Fittings are produced in redABS under a stringent quality control system.
Label plate for detector base S-Quad / IQ8Quad
Label-smoke detector pipes are manufacture from ABS (Acrylonitrile Butadiene Styrene), very lightweight, versatile material, guaranteeing you easy and professionalinstallation.
Light shield is available for installation in areas where direct sunlight cannot be avoided
The DST family of sampling tubes are pieces of steel piping with a series of holes drilled the entire length of the tube and should extend the entire width of the duct.
VESDA-E VEA microbore tubes are custom made, high quality plenum rated flame retardant polyethylene tubes. They have superior stress crack resistance for reliable long-term performance
VESDA-E VEA Microbore Tube Cutter are used for cutting microbore tubes.
Honeywell TR80 Wall Modules offers onboard Temperature & Humidity Sensors, integrated HVAC Display, Light and Blind control.
The mounting adapter is used for quick and secure attachment of bases of the IQ8Quad detector series, 9x00, IQ8Alarm Plus and alarm signaling devices, parallel detector indicators, etc. to suspended ceiling systems.
Mounting set is used for mounting the air duct construction set to round and/or insulated air ducts.
Mounting bracket is used for alignment of the industrial heat- and flame detectors UniVario. Simple installation with base Part No. 783313.
Mounting bracket for lintel installation
Mounting kit
Mounting rail for FACP
OSID wire guards are steel cages designed to protect OSID imagers and emitters from vandalism and accidental damage. The cages are constructed of heavy gauge steel wire with a corrosion-resistant polyester coating.
OSID environmental housings protect OSID imagers and emitters from dust and water ingress in industrial environments. The glazed housings are made of ABS and the glass windows cause minimal attenuation of the UV and IR beams.
Installation kits for OSID detectors include a laser alignment tool, a test filter, a PC cable, a cleaning cloth, and a manual.
OSP-002 laser alignment tools allow for quick alignment of OSID detectors. They also align and lock the eyeball and activate the emitters when locked.
OSP-003 acrylic test filters are intended for use with OSID detectors.
Flush Sample Point Head only for 10 mm OD tube.
Protects smoke detectors
Pipe cutter under pipes and Fittings products have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system.
Pipe Ties comes under accessories of pipes and fittings.
The Recessed Magnetic Contact comes with tamper loop and white finishes.
Gent S-Quad Sensor Bases are used for all S-Quad Sensors. Available in White or Black.
Sockel mit integriertem Isolator für den Notifier - Ringbus für Melder der Serie 700
B401 plug-in detector bases are used with System Sensor® conventional S300 smoke and heat detectors. These bases make detectors more versatile than equivalent direct-wired models.
SC111 day and night movable mounting kits are designed for use with SC100, SC105, and SC115 detectors. They provide extra protection to safe doors and prevent arming while doors are unprotected (can allow arming in night position only).
SMB600 flanged surface mounting kits may be used with certain System Sensor® smoke detectors when flush or recessed mounting are not possible.
The STI is an accessories that are been used with STI Stopper II®. The accessories that are been used are conduit gasket and conduit spacer.
The System Sensor SWIFT® Wireless system offers a ceiling AV base to support L-Series devices in wireless installations.
The System Sensor SWIFT® Wireless system offers a wall AV base to support L-Series devices in wireless installations.
Banderoles to mark the suction points
System Sensor Select Series detector color kits offer expanded color options to meet varying aesthetic applications.
Semi-flush fixing kit is designed to mount an S-Quad device. To semi-flush mount a special housing must be used which consists of a main assembly and a trim ring.
Replacement dust covers are for use with System Sensor® 100/200 Series smoke detectors.
Siemens FDOOTC241 / FDOOT241-A9 Baffle is with FDB222 base (pack of 10)
Single Row Blanking Plates are used to fill the enclosure if less sub racks are used than the enclosures maximum.
Spare Key Pack for 34450 & 34440 (2 keys)
Spare Key for Vigilon and Compact Outer Door (Pack of 10)
Spare Plastic Front cover for VES-A00-P smoke detector. It has LEDs in it for indication.
Gent Nano Spares Pack
Spares pack for Vigilon Compact
Protects System Sensor SPECTRAlert® Advance series horn/strobe/speaker notification appliances
The 19 inch rack enclosures are designed to house up to 20 display and programmer modules in a wide variety of configurations to suit the particular requirements of a site where centralised control and monitoring of the VESDA system is required.
System Sensor BEAMSMK are the surface mounting kit for the reflective projected beam smoke detector which are used whenever surface wiring is being used.
The T-Breaker Unit allows a spur to be created from a Gent analogue addressable loop circuit.
Top Hat Rail is available in 400mm.
VSP-972 filters are spare filters for use with VEA aspirating smoke detectors.
The VSP-976 is a display front panel for VESDA-E VEA series of smoke detectors.
Xtralis spare front cover is use with the VESDA-E VES & VESDA-E VEP Aspirating Smoke Detector. It consist of plastic with 3.5in Display size.
Xtralis VESDA Wall-Mounted High Level Interface (HLI) links VESDAnet1 with PC software monitoring tools, Building Management Systems (BMSs) and Fire Alarm Control Panels (FACPs).
The VESDA Modbus high level interface models links VESDAnet1 with PC software monitoring tools, building management systems (BMSs) or fire alarm control panels (FACPs). They are Type 2 models which have the echoing function is disabled.
VESDA CABLE GLAND SP XCL PK10
VESDA Sensepoint XCL Replacement Filter
VESDA Pipe and Fittings are part of an integrated system manufacturedfrom specialty plastics designed for use with most aspirating smoke detectionsystems, the VESDA VLP system in particular
VESDA-E Filter Cartridge is field replaceable filter of VESDA-E detectors. It filters coarse particles
VSP-960 is used as a mounting bracket for VESDA-E.
VESDA-E Sampling Module