CIPer™ Model 50 has you covered with expansion capabilities for up to 2,500 points. Built on the Niagara N4 Framework® and fully BACnet compliant, the CIPer Model 50 gives you a fully scalable solution for meeting both current and future needs.

Contains Diamond Actuator 27 lb-in (3 Nm) with crank arm and foot mounting kit

The TC500A Commercial Connected Thermostat automatically monitors and controls indoor comfort. It controls and monitors RTU, Heat Pump equipment, and their configurations.

Pneumatic remote bulb temperature controllers provide proportional control of pneumatic valves and damper actuators in HVAC.

ZonePRO™ TB6980 floating and TB7980 modulating digital thermostats provide proportional plus integral individual space temperature control in zoned commercial HVAC systems such as hydronic and pressure dependent VAV with or without reheat.

T675A/B and T678A temperature controllers regulate the temperature of air or liquids in ducts, pipes, tanks, and boilers. Typical uses include control of dampers and valves in heating, cooling, or heating-cooling systems.

The C7232 stand-alone Carbon Dioxide (CO2) Sensors and Controllers are used for determining ventilation necessity with HVAC controllers and to manage the amount of fresh outdoor air supplied to maintain acceptable levels of CO2 in the space.

Electronic temperature sensors are designed for use with T775 electronic controllers in commercial heating and cooling systems.

The MS4104, MS4109, MS4604, MS4609, MS8104 and MS8109 are spring return direct coupled actuators (DCA) for Fire and Smoke dampers.

SP470A pneumatic diverting switches provide a means of manually diverting air between various system components such as valves, thermostats, and damper operations in pneumatic control systems.

RP970A pneumatic capacity relays are direct acting, proportional relays with a 1:1 pressure ratio.

SP970 manual or minimum position pressure regulators are used to manually position a remote damper actuator or reset the setpoint of a pneumatic controller.

P658 pneumatic/electric switches convert a controller's pneumatic signal to electrical switching, providing start and stop control.

Plant control that is easy to install and use, even for new hires. Capabilities that are be easy to add, without rip-and-replace. And controls with built-in cybersecurity to protect OT, closing the backdoor to IT networks.

The C7233 & C7263 Series Sensors are a stand-alone carbon dioxide (CO2) sensors for use in determining ventilation necessity with HVAC controllers.

Honeywell C7364A are the TVOC Air Quality Sensor which uses an advanced MEMS metal oxide semiconductor sensor to detect poor air quality.

The TR71/TR75 Series are 2-wire, non-polarity sensitive, Sylk™ bus communicating wall modules for use with Honeywell programmable controllers.

The TR40 and TR42 series of room sensors and displays are designed to operate with Honeywell controllers. All models have an integral temperature sensor and variants are available that include sensors for relative humidity and/or CO2 concentration.

TR120 touch screen wall modules enable local controller configuration through an easy-to-use touchscreen interface with menu driven selections.

TB7200 Series PI thermostats are communicating thermostats specifically designed for zoning applications. All thermostats are PIR ready and can be ordered with or without Honeywell occupancy sensor.

The C7632 CO2 Sensors offer a fixed 0-2000ppm & fixed 0-10Vdc output, measure CO2 concentration in ventilated spaces or ducts. Used in ventilation & AC systems to control the amount of outdoor air supplied.

Rebuild kits for Honeywell globe valves include repack kits, replacement discs, and service parts, among others.

Spyder control even in small spaces means efficient operations and more versatile cost savings throughout your facility.

The WEB-HMI series of touchscreen monitors are HTML5 IP browser compatible touchscreen monitors. They combine state-of-the-art features and top performance with an outstanding design.

T775 Series 2000 electronic standalone controllers are the next generation of commercial and agricultural controls capable of remote sensing of temperature and providing switched and/or proportional outputs to various types of loads.

WEB-8000 controllers are compact embedded IoT (Internet of Things) devices and server platforms for connecting multiple diverse devices and subsystems.

1126 well assemblies come in a variety of diameters and insertion lengths.

221508A Modutrol IV Resistor Boards are used to controlling up to six Series 90s in parallel with a 135 ohm pot or slide wire type series 90 control

Position feedback and SPDT pilot duty auxiliary switches are used in conjunction with ML6984/ML7984 Series 4000 and higher (ML6984 in 5-wire mode only) globe valve actuators.

The C7355 air quality sensors monitor temperature, Humidity, carbon dioxide, particulate matter and TVOC all in one wall or duct mountable module. The device communication over RS485 and easily integrates with the BMS.

Spyder® BACnet® PUB programmable controllers are designed to control HVAC equipment. These controllers provide many options and advanced system features that allow state-of-the-art commercial building control.

Spyder® BACnet® programmable VAV controllers are MS/TP network devices designed to control HVAC equipment. Each controller is programmable and configurable using the Niagara Framework® software.

Spyder® LON programmable VAV/Unitary controllers are part of the Excel 10™ product line family. They are LonMark®-compliant devices designed to control HVAC equipment.

Spyder® LON programmable VAV controllers are free topology transceiver (FTT) LonMark® compliant devices designed to control HVAC equipment. Each controller is programmable and configurable using the Niagara Framework® software.

Spyder® Model 5 Unitary Controllers provide flexible, freely programmable, demand-led control that delivers tangible benefits to reduce energy spends and drives new levels of functionality and efficiency in today’s buildings.

Maximize comfort and maximize HVAC performance in any environment. Honeywell’s high-accuracy sensors measure humidity and temperature giving you the control you need within commercial buildings.

C7400 analog enthalpy sensors are for use with W7212 and W7459 economizer controllers.

Series 71, 72, and 76 Modutrol IV™ Motors are spring return and non-spring return motors used to control dampers and valves. The motors accept a current or voltage signal from an electronic controller to position a damper or valve.

Modutrol-motoronderdelen en -accessoires

Series 90 Modutrol IV™ Motors are spring return and non-spring return modulating proportional control motors. These motors are used with controllers that provide a Series 90 output to operate dampers or valves.

From commissioning to comfort, one thermostat feels right with every swipe: The Honeywell TC300 Commercial Thermostat supports a full range of fan coil and 1H/1C equipment configurations.

TR29 wall-mount enclosures can be used to wall-mount any 1/4-inch or 3/8-inch diameter probe sensor.

The 32003169-001 duct pick-ups are for use with P7640A pressure sensors.

Heat conductive compounds are for use with Aquastat® temperature controllers. They improve heat conduction in immersion well applications where the bulb does not fit tightly.

Proportional, high capacity, single or dual input pneumatic controller used in conjunction with remote sensors to provide proportional (P)

Excel T7515A-D M-CelTM space temperature sensors are platinum resistance temperature devices (RTDs) used with Excel MicroCellTM and MacroCelTM controllers to control variable air volume (VAV) terminal units and other equipment.

Honeywell panel bus I/O modules consist of a terminal sockets and a removable electronic modules, that allow for the sockets to be mounted and wired before the electronic modules are installed.

Sylk™ I/O modules are part of the Spyder® family of products and expand the footprint of a single Spyder device, increasing the controller's ability in situations that require a large amount of physical I/O.

MSxx03, MSxx05 Series Direct Coupled Actuator Accessories

The I/O modules are advanced expansion devices designed to integrate with a variety of Honeywell controllers. These are available in seventeen variants to cover all your application requirements.

The X45B_X06 relay pack is a Honeywell Integrated Room Automation System component.

Pneumatic Damper Actuator Parts and Accessories

UEC24014M262 Differential Pressure Switches open or close a switch in response to a change in the pressure across a pump or filter.

Interface Module For Modutrol Motors

The MCM34 multipurpose module can facilitate several functions in INNCOM’s Integrated Room Automation System

A part of the Honeywell Optimizer Suite, the Honeywell Optimizer Unitary Controller allows you to wire them or connect wirelessly – even take advantage of groundbreaking twisted pair T1L technology.

An E/P Transducer accepts a proportional voltage signal from an electronic controller and converts it into a proportional pneumatic signal of 0.2 to 1.0 bar to operate pneumatic actuators or reset pneumatic controllers.

C7772 wall plate temperature sensors are designed provide a resistive output signals proportional to sensed room or space temperature.

The C7262 Sensor is a stand-alone carbon dioxide (CO2) and temperature sensor for use in determining ventilation necessity with HVAC controllers. The C7262 measures the CO2 concentration and temperature in the ventilated space.

Pneumatic Accessories

Brass Compression Adaptor is used to facilitate the connection of impulse piping to differential pressure switch.

LonWorks® IF-LON2 interfaces can be used to connect Honeywell controllers via their USB port with LonWorks networks.

Accessories for Honeywell Advanced Controllers and I/O Modules

The X45B Controller Card is a CBL32 universal multi-functional analog/digital input/output controller device

A part of the Honeywell Optimizer Suite, the Honeywell Optimizer Unitary Controller allows you to wire them or connect wirelessly – even take advantage of groundbreaking twisted pair T1L technology

C7170 immersion sensors are intended for monitoring or controlling temperature in conjunction with an electronic control.

Thermostat calibration tools are for use with HP970/972 pneumatic humidistats.

Driver for LonWorks® Spyder Controllers

S637 Sail Switches respond to the air velocity in heating or warm air ducts, such as used in farm crop dryers. The switch completes a 24V or line voltage burner control circuit only when the blower or fan has produced a preset air velocity.

Software maintenance agreements (SMAs) for CIPer™ Model 30 and 50 are available for 18 months, 1, 3, and 5 years.

Auxiliary terminal blocks are for use with EXCEL® 5000 systems. They mount onto already installed pluggable I/O modules in order to equip them with additional terminals.

Thermostat tool kits are for use with TP900/970 Series pneumatic thermostats.

XL2000 External HMIs are cost effective, versatile mountable human machine interfaces for those Excel Web II controllers not equipped with a built-in HMI.

TP970/9600 Series Pneumatic Thermostat Accessories include back plate assemblies, filter assemblies and cartridges, plugs, resistor blocks, wall plates, mounting hardware, thermostat cover kits, satin/chrome cover assemblies, and more.

Receiver Gauge

T755 temperature sensors are simple to use, broadly featured electronic temperature and universal controllers. Some typical applications for the T755 temperature sensors include monitoring return air, discharge air, and mixed air temperatures.

The Q5001 Valve Linkage connects a Modutrol Motor to a 2- or 3-way valve. It is used primarily on V5011 or V5013 steam and water valves.

Free topology transceiver (FTT)/linked power transceiver (LPT) network termination modules are used with Excel 10™ controllers. 

Yoke Assmbly MP953B

The TR Series Wireless Wall Modules And Receivers by Honeywell meet the demand for energy-efficient, accurate control without the time and cost of wiring.

Pluggable Panel Bus Modules allow you to monitor and control remote points using 2-wire communication with the main controller.

For use with ML Series Rotary Direct Coupled Actuators

Pneumatic Actuator Replacement Diaphragm

Scalable, fast and flexible to handle a range of devices. CIPer Model 30 is an Internet Protocol (IP) based, Niagara 4 controller that can be used for VAV, unitary, equipment and plant applications.

T77 Wall Modules provide the following additional combination of options to the customer: analog setpoint input and for models used with Excel 10™ controllers, override (bypass) digital input contact, LED status indicator and network access jack.

Repair Kit Diaphragms used for pneumatic damper actuator valve (MP953A and MP953C).

MLxx20/21/25 Linear Valve Actuator Parts and Accessories

T991A proportional temperature controllers provide modulating control of water or air temperatures in ducts, tanks, and similar applications.

T631A-C controllers provide line voltage control of heating, cooling, and ventilation systems in farm buildings or storage areas.

VP512A unit ventilator valves are normally-open, single-seated, straight-through or angled globe valves for proportional control of either steam or hot water in unit ventilators.

VGF Flanged Globe Valves are used for 2-position or modulating control of steam, hot water, or chilled water in closed loop HVAC systems.

Valve Repack/Rebuild Kit

Linear Valve Accessory, Packing Kit for V5050A/B, V5016, V5025 in sizes DN100-150; V5049 in sizes DN80-150

Rebuild kits are used with V5011 and V5013 valves.

14001046-004/U cover fasteners are used with VP527A, VP526A, VP531A/C, VP525A/C pneumatic valves.

MS3103, MS3105, MS4103, MS4105, MS7403, MS7405, MS7503, MS7505, MS8103, MS8105 Spring Return Direct Coupled Actuators (DCA) are used within heating, ventilating, and air-conditioning (HVAC) systems.

The Excel Web II is Honeywell’s Ethernet-based, freely programmable Building Automation controller. The controller provides network security, universal operation and reduces total installation cost for building investors and building operators.

Q7751A Excel 10™ routers double the bus length and the number of usable nodes on a LonWorks® (previously called E-Bus) networks.

Parts and accessories that are designed for use with dampers, such as damper crank assemblies, crank arms, bearings, adapter arms, and drive ears, among others.

Ball Joints, Push Rods and Crank Arms

Pneumatic water valve springs are used to change the actuator pressure range. The range is differentiated by spring color.

TP974 are direct-acting, proportioning temperature sensors used with pneumatic controllers to control valve and damper actuators for one- or two-pipe installations.

Touch Panel Interface

RP913 diaphragm logic pressure selectors are used in pneumatic control applications to select the highest and/or lowest pressure input from zone thermostats.

RP418 and RP818 electric/pneumatic relays are solenoid valves which open and close the air supply to pneumatic controls. The control input is an on-off line voltage signal to the RP418A-C and 24V AC signal to the RP818A and B.

Series 2000 humidity and temperature transducers are highly accurate, stable humidity transducers designed for use with HVAC controllers such as the T7350 thermostat, H775 remote humidity controller, and W7760 direct digital controllers.

WEBs N4 supervisors allow networking for multiple Niagara based WEB-8000 and CIPer™ 10 controllers, along with other IP-based controllers and field devices.

MCSS/MCSP current switches are miniature Go/No Go current status switches designed to provide status information on AC current supplied equipment.

198162JA, EA, GA, and AA model transformers are used to convert line voltage to 24V AC to power Honeywell Modutrol IV™ motors. 198162JA provides 24V AC isolation, mainly for M723 and M934 replacement motors.

CP980 Velocitrol velocity sensor and controllers combine ultra sensitive air velocity sensors with pneumatic controllers to detect and control airflow in air terminal units, independent of system static pressure.

TB wall temperature sensors by Honeywell are 10K ohm NTC Type II remote wall sensors for use with the TB7200, TB7300, and TB7600 Series communicating thermostats and other devices requiring a 10K ohm NTC Type II sensor.

Honeywell provides pneumatic actuators for air dampers.

ML6161 and ML6174 Non-Spring Return Actuators are designed to control VAV terminal unit dampers or Honeywell ball valves.

Temperature sensors for ZonePRO® thermostats are used in low voltage pressure-dependent applications.

LP914A and LP915A pneumatic sensors are proportional-type temperature sensors that are used with pneumatic controllers to manage pneumatic values and damper actuators. LP914A and LP915A pneumatic sensors can be duct-, well-, or wall-mounted sensors.

The X45R8 Universal Relay Pack enables switching control of INNCOM guestroom lighting and HVAC equipment.

The people in your building want to know that the air they breathe is monitored for their well-being. The TR50 provides simple visual confirmation of air quality, with an optional display to show up to five key components of air health.

The high-efficiency F58G,H Commercial Electronic Air Cleaner is mounted to the return air duct of a forced-air heating, cooling, or ventilating system, capturing a significant amount of airborne particles 0.3 micron and larger.

Decorative Plate for TC500

Q298 damper linkages connect M833, M835, M836, and M7415 economizer motors to 1- or 2-zone dampers. These linkages may be used to link shafts of two dampers together.