Morley-IAS MI-DCMOE-HC control output modules are used with the ZX series of intelligent control panels.
Addressable monitor module with 10 input circuits, used for the supervision of alarm initiating equipment or technical signals that have a voltage-free contact.
Micro processed 12-zone fire detection control panel incorporates source supply of 2 supervised siren outputs, general alarm relay, general fault relay, general indicators and provides digital input for remote reset,
2-way relay board for BMZ series NFS
The morley-IAS power supply units are 2 ampere power supply units used for ZX1e/2e.
ZX1/2Se retrofit 4 line display kit including display plate and overlay.
MI-CR6-S2I Multi Module is an Addressable control module with 6 output circuits in NO/NC relay form. This module is recommended for activation through the communications loop of doors, fire dampers, lift stops, etc.
Conventional 6-zone analog monitor modules are used for equipment control conventional alarm. Monitor modules are addressable using decadic selectors.
6500 Thermal Detectors are intelligent detectors with point ID capability that enable each detector address to be set with decade address switches to provide exact detector locations. They provides fixed high temperature detection at 190°F.
6500RS are conventional reflector- type linear optical beam smoke detectors designed to operate as a component of a conventional fire alarm system
Morley-IAS 795-131 is a Loop Splitter Card for DXC control panels.
8 way input/output cards Provide up to 8 configurable relay outputs or up to 4 command inputs and 4 outputs.
ASD-TP is a series of Smoke detector modules used for smoke detection in difficult enviroments. This Series gives a range of modules that are compatible with ALL-SPEC and FREZZER Air sampling devices (ASD).
ATEX Cable Holders are required for Armored Cables and they are complete of rubber parts.
RF-FTX Additional filter accessories are used for HPX-751E HARSH ™ analog addressable aspiration detectors.
The call points are an addressable break glass manual call points which has a simple rotary decade switch at the rear of the unit for addressing.
The MI-HTSE-S2I is Morley 78°C fixed temperature analogue addressable sensors, with isolator, employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing, part of Morley Heat Sensors Line.
The MI-FHSE-S2I is Morley 58°C fixed temperature analogue addressable sensors, with isolator, employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing, part of Morley Heat Sensors Line.
The MI-RHSE-S2I is Morley rate of rise heat addressable sensor, with isolator, part of Morley Heat Sensors line.
The high sensitivity intelligent smoke detectors provides an extremely high sensitivity to fire conditions, by detecting the earliest particles of combustion.
Addressable Manual Call Point is an MCP that has a simple rotary decade switch at the rear of the unit for addressing. Call Point is designed to provide a manual alarm interface to Morley IAS’s fire alarm control panel.
Addressable Output Module is loop powered devices controlling an unsupervised double pole relay output.
Aspiration reducing film sheet accessories are used in aspirating systems and they are available in various size such as 2.0mm to up to 6.0mm.
The BS7273-4 MorleyIAS door release systems are designed for new installations and comprises a packaged solution.
This is a battery that is a 12 volt 12Ah valve-regulated, maintenance-free battery with no electrolyte leakage from the case or terminals.
Battery box or mounting enclosure which has Size 500 x 500 x 185mm (H x W x D).
Central Extinguishing Unit as system status indicator LEDs and a display with two digits of the operating time discharge.
Communication cards are required to connect the control panel to the MK-VSN configuration tool and to a Central Station. They are compatible with standard protocol Contact ID, via the telephone line.
Communication Modules are use in the ZX series intelligent multi-protocol fire alarm control panels & These optional modules add optically isolated communication ports to the ZX series control panels
The Horizon series of conventional control panels 2 Zone has been developed to provide a simple and reliable solution to the demands of today’s fire detection solutions.
The Horizon series of conventional control panels 4 Zone has been developed to provide a simple and reliable solution to the demands of today’s fire detection solutions.
The Horizon series of conventional control panels 8 Zone has been developed to provide a simple and reliable solution to the demands of today’s fire detection solutions.
Conventional Fire Alarm Control Panels by Horizon Range offers an out of the box and on the wall solution.
The conventional manual call points are designed to provide manual alarm interface to non-intelligent fire alarm control panels. They provide unique plug and play concept design which reduces installation time.
Conventional system indoor sirens with optical indicator includes labels with the text "FIRE", "FOGO", "FIRE" and "INCENDIO". These sirens use piezoelectric transducer and they generate 90dB acoustic power.
The conventional system LED remote indicators with boosters are designed for direct connection to all Morley-ias fire directors. These indicators have an own amplifier which allows the connection of several indicators in a single detector.
Conventional system outdoor sirens with optical indicators are available in multi-languages such as Catalan, French, English, and Portuguese. These sirens use piezoelectric transducer and they generate 90dB acoustic power.
The DX Connexion is an enhancement of the Morley-IAS Dimension panel range. The DX Connexion Panel series also include the modular unit PCB and Base Card.
Morley 796-152 is a 2 Loop Plug-in Card use in Dimension DX4 series fire alarm control panels.
The Single Loop Base Card is a spare part for DX1 control panel.
DX Spare Keys are used for DX series Keyswitch kits and are available in a pack of 5.
DX-M Control Panel Covers are available with printer slot
The Morley-IAS DX Connexion panel is ideally suited for use in the protection of small to medium sized buildings.
The DXc Blank Covers are a part of cover kits for DXc series control panels.
DXc custom key plate cover kit accessories are used to replace the blank cover supplied with the DXc2/4 control panels or used with the extension back box.
The Morley IAS DXc Flush Bezel Kit used for Morley IAS DXc2 or DXc4 panel and the kit includes additional extension back box. Extension box is used to accommodate larger batteries, relays or other equipment.
DXc Network card are fitted to each panel in order to create a network and to connect panels together.
Morley-IAS Fire Alarm Control Panel has qualities of reliability, flexibility and value with advanced features and intuitive functionality.
DXc replacement door is available for DXc control panels. This replacement door is fits with all three variants of the panel, DXc1, DXc2 & DXc4 and is supplied complete with display PCB, fascia label, ribbon cable and lock.
A replacement text inserts pack includes all text inserts/slide-in labels including both blank and numbered labels for Zone LEDs.
DXc System IO Card Interfaces are used in DXc1-M (714-001-214) & DXc2-M (714-001-224) fire alarm control panels. This I/O cards are used in sounder circuits, Fire Routing interface, Fault Routing interface and Fire Protection interface.
DXc1 rack mounting kit accessories are used for DXc1 one loop fire alarm control panels.
Detector parallel display
Digital Multi Detector is multi-criteria, multi-sensor Photo Thermal Infra Red detector is the environmentally friendly alternative to the ionisation detector.
Dimension series loop base card accessories are used in Dimension series fire alarm control panels.
The MI-D2ICMO dual input/single output modules are used with the Morley-IAS intelligent fire alarm control panels to provide a dual input circuit from external devices and a single relay control output circuit.
ECO1003 optical smoke sensors use state-of-the-art optical chambers combined with application-specific integrated circuits (ASIC) to provide quick and accurate detection of fires.
The Edge Clips are used in cable based linear heat detection (LHD) systems.
End line termination kit accessories are used for linear heat detection systems.
Engineer's Software Programming Kit is CD for configuring the Fire 3, Fire 4, Fire 5, Fire 6, Dimention tools.
Expansion housing for DXc series BMZ
Morley - IAS' Extension Back Box Bezels are flush mounting bezels that fits a DXc1 panel with additional extension back box.
External Paging Interface Module supports SCOPE, ASCOM/ TELENOVA and HLSUK paging products. It Requires RS485 card to be fitted in control panel.
F5000-LRK are long range kit for linear detector consisting of 3 reflectors to form a set of four that is included with the F5000M or F5000S detector.
Fire Detection Panels are designed for the installation of fire detection systems of small and medium size. They are available in painted steel housing material.
Morley spare installation Kits are used for the horizon series of fire alarm control panel. Installation kits includes 8 capacitive end of lines, battery leads, Allen key, panel controls key and sounder end of line resistors.
Flush Bezel Kits by Honeywell are covers can be purchased to suit your needs and include a blank cover, Customer key plate and 80 Zone LED expansion cover.
Flush Bezel kit is used in DXC1.
The TG main graphic management software is programmed for representation and complete control of the system and commands from a PC, and the software is compatible with Morley-IAS VSN-PLUS control panels.
Graphics software and dongle package enables the display of key information from their analogue addressable fire detection and fire alarm system.
The HM Series Photoelectric smoke detectors by Honeywell deliver high responsiveness, reduced sensitivity to dust and false alarms resulting from ingress of insect and other debris.
Hochiki ESP Loop Driver Cards are used as accessory for ZX5e and ZXSe fire alarm control panels.
ALL-SPEC2 Universal Air Sampling Smoke Detection System by Morley-IAS is a universal air sampling device for a broad range of applications. A high degree of modularity makes it possible to achieve a cost-effective solution.
Honeywell Loop Driver Card is used for Apollo S90 protocol.
Honeywell Loop Driver Card is used for Apollo XP95 or Discovery protocol.
The 797-062 is a Semi flush mounting kit for ZX5(S)e control panel.
Horizon Conventional Fire Alarm Control Panels are a reliable fire alarm detection solution that have been equipped with configurable class change inputs, coincidence detection and programmable delays.
The Horizon Range Thermal Detectors have been produced using the latest in manufacturing technology and supplied with an array of advanced features, making them “better by design”.
IRK Booster Module is used for linking several IRK-E-SI remote indicators.
IRK Waterproof Remote Indicators are used for displaying the alarm status of a point fire detectors. The LED in the remote indicator is lights up when the detector goes into alarm.
The MI-D2ICMO dual input/single output modules are used with the Morley-IAS intelligent fire alarm control panels to provide a dual input circuit from external devices
Morley MI-DSS-PC series provides Loop-Powered Open Category Detector Base Sounder Strobes with Isolated Version & Non-Isolated Version. The range is used in analogue addressable fire alarm systems.
The range of intelligent audio visual wall mount sounders are designed to be connected to analogue addressable fire alarm systems. These sounders receive their power from the loop, and can be controlled via the communication protocol(s).
The intelligent manual call points are designed to provide manual alarm interface to Morley-IAS fire alarm control panels.
The intelligent wall mount sounder strobes are designed to be connected to analogue addressable fire alarm systems. These modules are developed on the basis of piezoelectric transducer and high output LED array technology.
Intelligent water resistant version red color manual call point surfaces are designed with break glasss element and isolator.
Intelligent Call Points by Morley-IAS are designed to provide a manual alarm interface to Morley IAS’s fire alarm control panel.
Terminal Block by Morley-IAS is an integral part of accessories by Intelligent Systems.
The internal thermal printer kit is accessories used for DX-M series intelligent fire alarm control panel. It’s also requires for 797-073 control panel cover.
LCD Annuciators by Honeywell are provides system status indicators for AC Power, Alarm, Trouble, Supervisory, and Alarm Silenced conditions.
The linear heat detection electronic interface modules allows early detection of fire or overheating. The electronic interface modules consists of two compnents the sensor cable and the alarmline control unit LWM-1.
Linear heat detection standard high resistance intelligent cables are recommended for environments ranging from clean and dry to moderate dust and moisture.
The Manual Call Points are designed to provide a manual alarm interface to conventional fire alarm control panel. Manual Call Points offers flexible and break glass element option and available in red, yellow, green and white colour.
The MCP5A product has the Advanced Protocol embedded. A version of this call point with built in isolation is also available.
The Addressable Input, Output Module cards includes 5 monitored input modules and 5 relay outputs (30V DC-1A). This cards are delivered with end-of-line resistors for the 5 inputs.
Conventional Zone Interface module provides an interface between a zone of Morley IAS manufactured conventional type fire detection devices and an intelligent signalling loop. It has a single-tri colour LED which indicates the status of the module.
MI-DCMO Adressable Control O/P Module is used to operate dry contacts for door holders, air handling unit shut down or other similar functions.
The MI-DCZRM addressable zone monitor module allows a zone of non-addressable devices to communicate with a Morley-IAS protocol analogue addressable system.
MI-DSS-PC are Loop Powered Open Category Detector Base Sounder Strobe available in isolated/ non isolated version. The MI-DSS-PC requires a B501AP base for fast and simple installation for Morley detectors.
The MI-LPB2 are addressable reflector- type linear optical beam smoke detectors, designed to operate as a component of an intelligent fire alarm system.
Master motorized IR beam linear smoke detectors are composed of a motorized linear detector, a reflector up to 50m and a remote control unit with LCD display and multifunction keyboard.
The Morley-IAS Micro Monitor Modules are used in conjunction with the ZX series intelligent multi-protocol fire alarm control panels and provides an interface between the normally-open contact alarm initiating devices.
Morley - Dual channel capability with two high sensitivity smoke sensors in separate chambers. (One sensor for each channel) - Loop Connected Aspirating Systems
Morley - Single channel capability with one high sensitivity smoke sensor - Loop Connected Aspirating Systems
Morley - Single channel capability with two high sensitivity smoke sensors in a common chamber for coincidence detection. - Loop Connected Aspirating Systems
The Addressable Monitor Modules are used with the Morley-IAS intelligent fire alarm control panels to provide a single or dual input circuit from external devices.
Morley printer Paper Roll & Ribbon used for ZXe/ZXSe Internal Printer Module for use with ZX5Se panels.
Morley ZXse RMU Module Kit provides an IP interface from panels to AMX graphics package.
Morley-IAS Aspirating Smoke Detectors are compact and cost effective ASD for monitoring small to medium-sized spaces and equipment. The unit can monitor up to 5 rooms.
Morley-IAS Bezel Kits are semi flush mounting kit for ZX1(S)e or ZX2(S)e control panel.
Morley-IAS DXc Expansion Mimic PCB Includes Silence Sounders, 2 Level Access Key, Allows Geographic ‘Floor Map’ Zonal Indicators To Be Built For Situations Where Increased Clarity Of The Fire Location
The Key and cylinder kits are for DX CONNEXION control panels that allows the user to access level 2 function keys without using a password.
Morley-IAS ZXSe Fire Alarm Control Panel is an Intelligent Fire Alarm Control Panel. It has been designed and constructed around proven and reliable microprocessor technology.
Multi-mount metal enclosures are capable for housingmmX-10ME, CMX-10RME or MCX-55 modules.
Multiple mounting support brackets allows the F5000M or F5000S detector to be installed on sloping ceilings or walls with an angle greater than 10º.
The network 16 digital type B outstations are compatible with all network 16 systems and are available in both surface and flush types and available in either red or green finishes.
Der MI-PTSE Photo Thermischer Melder nutzt thermische Unterstützung für den Kern photoelektrischen Rauchmelder, um verbesserte Falschalarm Immunität und schnellere Reaktion auf eine breite Palette von beginnenden Bränden zu geben.
The OMV outdoor motion viewers are wireless, battery operated cameras. Cameras are designed for use in a Videofied® security system.
PC interface lead accessories are used for programming all Morley-IAS control panels.
The temperature sensor cables are linear heat detectors that detects heat at any point along its length. Sensor cables consists of two conductors individually insulated by a polymer sensitive to temperature increase.
The paging system full duplex repeaters are the purpose designed repeaters for the Honeywell response paging system. They are used to extend radio coverage with the response paging family on fire event messages.
The paging system rechargeable docking stations are used for TFT pagers. These docking stations are available in three types such as 6-way, 12-way, and 15-way.
Paging system response link is an entry level paging system suitable for a range of applications.
The MI-PSE-S2I Photoelectric smoke detector has an integrated isolator and delivers improved responsiveness, reduced sensitivity changes caused by settling dust and reduced false alarms resulting from ingress of insect and other debris.
Power supply extension for DXc1-M and DXc2-M
Protectowire linear heat detectors are proprietary cables that detects heat anywhere along its length, these sensor cables are comprised of two steel conductors individually insulated with a heat sensitive polymer.
Rack mount kit fits a DXc2 panel or DXc4 panel.
Remote Connection Hardwares are Morley Echoback device disablement logging activation
Remote laser test tools are used in in conjunction with the Vision range of detectors for triggering the Vision detector. These test tools have hand held unit which provides an effortless-way of remotely triggering the Vision detector.
The ZX Series range of 1, 2 or 5 loop modular, scalable intelligent fire alarm control panels is suitable for protecting all types of medium to large properties.
The resettable manual call points are exclusively use for indoor applications. These call points includes three types of selection activation, by zener diode, or bye NO/NC contact or by 470 ohm resistance.
The response aid paging systems provides an easy-to-use, cost effective solutions to support deaf and hard of hearing people in case of a fire emergency.
Remote Indicators provide visual indication of an alarm on a concealed conventional or addressable detector.
The response paging site survey kits offers an all-in-one solution for conducting regular paging site surveys.
The response paging system includes response, rechargeable and rechargeable TFT display pagers. The response paging system’s response and rechargeable pagers are simple, compact and discreet personal devices for short messages.
Rechargeable pager battery accessories are used in response paging system.
Response paging system spare cables are used in response paging site survey kits.
The Notifier HLS-RES series are contact interface units for use with the Response Plus and Response Aid paging systems.
Response Radio Paging Licence is provided for Response Paging System.
The SMX Fire Alarm Control Panel model by Honeywell is designed keeping in mind the needs of today’s performance conscious establishments.
The STX Fire Alarm Conprol Panel model by honeywell is designed keeping in mind the needs of today’s performance conscious establishments.
Set of EPROMS intelligent systems spare parts are used for Zxe series panels.
Morley 796-171 is a replacement/spare base PCB/motherboard for the Morley ZX1SE fire alarm control panel.
Single Terminal Back Boxes are used for mounting RTS151 key. Remote annunciator accessories providing reset function and has a Red LED to indicate alarm conditions.
The Six Supervised Control Modules are intended for switching applications involving DC which require wiring supervision such as an intelligent alarm system.
F5000 barriers allow the protection of large areas and the small size of its detector makes it go unnoticed self-aligning function with servo remote control.
ALL-SPEC series are universal air sampling devices.
Surface Mounting Boxes by KAC are providing a unique ‘plug and play’ concept designed specifically to reduce installation time.
Thermal printer paper rolls are replacement paper rolls for the 795-060-002 external printer of Morley ZX series fire alarm panel range.
Transformer Rectifier by Morley- IAS designed for fire and access control applications that require remote control of the power supply output.
Conventional Control Panels with 4 zones has been conceived and designed for the installation of small and medium-sized fire detection systems in those places where it is necessary to interface with an easy and high-performance central unit.
Conventional Control Panels with 8 zones has been conceived and designed for the installation of small and medium-sized fire detection systems in those places where it is necessary to interface with an easy and high-performance central unit.
Vision LT Conventional Central Control Panels are a range of easy to use panels which are compatible with a wide range of end of line resistors and simplifies replacement of obsolete equipment.
Visualeyez Alarm management is a pictorial and textual aid for managing alarm activations in your work place. It can be programmed to suit any applications including Hospitals, Universities, Prisons, Hotels, Industrial and Commercial buildings.
Morley-IAS MI-D240CMO control output module is used with the Morley-IAS intelligent fire alarm control panels to provide management of 240Vac loads.
Morley 796-158 is a Display PCB for ZX Series Control panels.
Glass front door kit are use with the ZX5e intelligent addressable control panel.
ZX range spare parts base PCBs consists of 5 loops and are used for ZXSe intelligent multi-protocol fire alarm control panel.
ZX Range Spare parts are used in ZX series control panels
The ZX series is an intelligent fire alarm control panel. The ZX series simple approach has produced a modular scalable fire alarm platform suitable for protecting all types of premises.
The ZX range of 1, 2 or 5 loop modular, scalable intelligent fire alarm control panels are suitable for protecting all types of medium to large properties.
Battery box or Mounting enclosure for ZX1/2Se control panel by Morley IAs
The Morley IAS by Honeywell presents ZX5SE series semi-flush mounting bezel kits which forms a part of ZX5SE fire alarm control panel. They are used for the Morley IAS active & passive repeater panel range.
ZX5SE Door is a spare part for intelligent fire alarm control panel.
The Morley 796-181 is 4 line Display Kit used for the Morley ZX5Se fire alarm control panel. This kit includes the Display Plate and Overlay.
Morley ZXse AMX Level software and regular licence enables the display of key information from their analogue addressable fire detection and fire alarm system. It can be upgraded with the features to extend the software capabilities.
The ZXSe range of analogue addressable fire alarm control panels have been designed and constructed around proven and reliable microprocessor technology.
The ZXSe range of intelligent fire alarm control panels has been designed to assist with the normal operation of a fire detection system.
ZXSe Mounting Brackets are 'L’ shaped to fit peripheral pcb’s into Zxe/ZX5e/ZXSe
Zone LED kits are available that include PCB, ribbon cable, zone number labels & fixings. Zone LED PCB is fitted to the lower half of the front door.
ZxSe Replacement Softwares comes with intelligent, sophisticated features like AUTOLEARN which aid with the initial system installation
Start your search with category name, product name, part number, etc.
Copyright © 2022 Honeywell International Inc.