The Xtralis Smoke and Gas System Management Center

VESDA-E VEA-40 Aspirating Smoke Detector with LEDs

The VESDA replacement filter cartridge (VSP-005 for single units and VSP-025 for a pack of 20) is used to replace filter cartridges in VESDA VLC, VLF, VLP and VLS detectors.

The VEU series of aspirating smoke detectors are premium detectors of the VESDA-E range. A range of revolutionary new features provide unsurpassed detection performance, flexibility, field programmability, connectivity.

VES aspirating smoke detectors are advanced detectors that include valve mechanisms in their inlets manifolds, as well as software to control airflow from the four sectors (pipes).

VESDA-E VEP Smoke Detector's is Built on the Flair detection technology and years of application experience, VEP detectors achieve consistent performance over their lifetime via absolute calibration.

VESDA-E VEP Smoke Detector's is Built on the Flair detection technology and years of application experience, VEP detectors achieve consistent performance over their lifetime via absolute calibration.

LF42285/LF42286 single-zone probe kits are designed for use with XAS-1-US air sampling units. They include a 2-hole sample and exhaust tube kit.

Banderoles to mark the suction points

The 19 inch rack enclosures are designed to house up to 20 display and programmer modules in a wide variety of configurations to suit the particular requirements of a site where centralised control and monitoring of the VESDA system is required.

OSID environmental housings protect OSID imagers and emitters from dust and water ingress in industrial environments. The glazed housings are made of ABS and the glass windows cause minimal attenuation of the UV and IR beams.

OSID environmental housings protect OSID imagers and emitters from dust and water ingress in industrial environments. The glazed housings are made of ABS and the glass windows cause minimal attenuation of the UV and IR beams.

VESDA-E VEA-40 Mounting Bracket is an accessory for VESDA-E VEA Local Relay StaX.

OSID-SK

OSID Receiver (Open-area Smoke Imaging Detection) with 7° coverage. A technological innovation in the field of linear optical detection.

Anti-Condensation Film is used for OSID-EH housings. An easy applicable film that provide long time resistance to condensation on the glass fronts.

OSID beam detector FTDI cables allow connection of a PC with OSID diagnostic software to the imager.

VESDA-E VEA microbore tubes are custom made, high quality plenum rated flame retardant polyethylene tubes. They have superior stress crack resistance for reliable long-term performance.

VESDA Gateway with VHX-1420-HFS

The Smoke Pen simplifies Aspirating Smoke Detection (ASD) system testing by providing a userfriendly design that generates a continuous smoke to test the pipe network.

VESDA-E REMOTE DISPLAY, RELAY AND 19" SUBRACK

ASD pipe accessories provide quick smoothly installation

VESDA-E VEA-40 Aspirating Smoke Detector with 3.5” Display

Notifier intelligent reflective graphic linear beam detector

The VESDA Power Supply has been designed to power a single unit to multiple units depending on application needs.

Convert from 27mm to 25mm pipe connector

VESDA-E VEP/VEU Flow Sensor Manifold replacement spare part.

There are many types of isolation valves but the most common used with aspirating smoke detectors are ball type valves

pipe elbow of 3/4in” nominal Schedule 40 CPVC fittings to make necessary pipe network connections, turns and terminations

VESDA® VLF-500 smoke detectors are early-warning detectors designed to protect small, business-critical environments of less than 500 m² (5,380 ft²).

Open-area Smoke Imaging Detection (OSID) Receiver Unit with 80 ° coverage. A technological innovation in the field of linear optical detection. Range detection:6-34m.

VESDA MANIFOLD ULTRASONIC FLOW VLI

This conventional, single-ended beam smoke detector is easy to install - only one side needs to be wired.

Li-ion Tamer Gen 3 Controller

Li-ion Tamer Gen 3 Demo Kit

3/4in nominal Schedule 40 CPVC fitting to make necessary pipe network terminations.

VESDA Sensepoint XCL Spare - XCL-SC-NH3: Spare Replacement Gas Sensor- XCL-VEA-CAL: VESDA XCL Micro Bore Flow Cap

Li-ion Tamer Gen 3 Ethernet Switches

Li-ion Tamer Gen 3 Power Supplies

Li-ion Tamer Gen 3 Relays

Li-ion Tamer Gen 3 Hub Xtralis

Li-ion Tamer Gen 3 Sensors

Li-ion Tamer Gen 3 Network RJ45 Ethernet Cable

ASPIRATING EQUIP CONN. 25MM FLEX. 30CM Grey

ASPIRATING EQUIP 25 mm x 12" Condensation Valve Trap with Ball Valve Grey

ASPIRATING EQUIP CONN. 25MM FLEX. 1M Grey

ASPIRATING EQUIP ACCY Conical Sample Kit 2m flexible 10mm tube Grey

ASPIRATING EQUIP ACCY flush Sample Kit 2m flexible 10mm tube Grey

25 mm ABS Self Draining Water Trap Grey

ASD QUICK REL KIT AIR LINE ABS 3/4" Grey

ASPIRATING EQUIP END-OF-LINE VALVE (25 mm Large Check Valve (blow out valve)

At the Advanced Detection Global Services (ADGS) training center, we provide high quality trainings based on many years of firsthand field experience in advance smoke and gas detection technologies. ADGS offers different training programs

Advanced Detection Global Services (ADGS) offers new Design review Service to assure that design, Calculation & Programing are working against Standard, Codes, detector specification, protected environment requirements and best practice.

CPVC socket unions are used in combination with pipe fittings and related accessories to complete pipe networks in Fire Alarm Aspiration Sensing Technology