90521 Line Filter
Eltek compact, light and switched plug-in AC/DC adapter. Used for simple applications where a 24V power supply without battery backup is required.
Addressable ring line driver with integrated isolator for the NOTIFIER ring bus
The System Sensor M500M-4-20 analog input module demonstrates our commitment to offer solutions for all applications.
Analog Output Module is designed for connection via Analog signal to a BMS system.
BE600A-N Spare Part are CPU board with AM-6000 power supply
Digital Key Module DKM plus
The Dual Loop Interface Board is an intelligent fire alarm panel offers a technically sophisticated range of facilities and functions whilst remaining easy to install, program and operate.
End-of-line (EOL) resistors are sold in packs of 10 and are available in 4.7 or 47K Ohm.
The System Sensor M500X Fault Isolator modules enable part of the communications signaling line circuit to continue operating when a short circuit occurs. The Module is an automatic switch that opens when the line voltage drops below four volts.
Fibre Multimode Converters media converters are equipped with a multiple interface circuit that can handle RS-232 or RS-422/485 serial interfaces and multi-mode fibre.
Pluggable Fiber Optic module for the fiber optic switch 583394.11 in 1310 nm multimode. This provide a Fiber Optic cable length up to 2 km.
Fire Alarm Computer Plug-In Cards provide a modular design with different micromodules and individual extension concepts, that allow the Fire Alarm Computer to be easily adapted to special requirements.
Galvanic Isolators are single channel isolated repeater. They are suitable for use as an intrinsically safe isolator between an IMX-1E translator module and up to a maximum of 15 x IDX-751 AE intrinsically safe photoelectric smoke sensors.
Galvanically isolated RS232 card BMZ NF 300 to NF 5000
Heat detectors respond to changes in temperature and are better suited to smoky, dusty or steamy environments than smoke detectors.
Honeywell Loop Driver Card is used for Apollo S90 protocol.
Honeywell Loop Driver Card is used for Apollo XP95 or Discovery protocol.
ISO-6 six fault isolator modules provide six equivalent circuits that will allow a portion of the communications loop to continue operating when a short circuit occurs on that loop.
The System Sensor ISO524-1 short circuit isolator is designed for use with all 200 and 500 series analogue addressable detectors and modules. They prevent an entire communications loop from being disabled when a short circuit occurs.
Input Output cards by Gent are designed for installation in EN54 Vigilon analogue addressable fire panels and Network node.
Isolator Module by Notifier is used with FireWarden Series panels to protect the system against wire-to-wire short circuits on the SLC loop.
Single loop circuit module for up to 127 bus devices, and esserbus-PLus (powered loop) devices according to the load factor.
Loop isolator for transponder
Fire phone Control Modules are intended for use in intelligent, two wire systems where individual address of each module is selected using the built-in rotary switches. They are used to connect a remote telephone to a centralized telephone console.
Morley DXc RMU Module Kit provides an IP interface from panel to AMX graphics package.
Morley ZXse RMU Module Kit provides an IP interface from panels to AMX graphics package.
Isolator provides full electrical isolation for bidirectional serial communication between two RS-232 devices in a compact, industrial-grade package.
NRX Radio Input-Output Modules are battery operated RF device designed for use with the NRXI-GATE radio gateway, running on an addressable fire system.
Optional Cards are used to connect the LCD-8000-L displays on CAN Bus Network between Boxes.
Overvoltage protection (OVP) to protect electrical and electronic devices from excessive electrical voltages.
RS 232/TTY serial interface module
Radio Input-Output Modules are battery operated RF devices designed for use with the radio gateway, running on an addressable fire system using a compatible proprietary communication protocol.
Releasing Solenoid Interfaces by Gamewell-FCI are providing intelligent analog addressable control functionality complete with full solenoid supervision and transient voltage suppression.
Residential silence modules/switches are designed to provide a means to silence signals and speakers that are connected to them for up to 10 minutes during an alarm condition.
SD500-LK dual action conversion kits are used to convert the SD500-PS (single action pull station) to a SD500-PSDA (dual action pull station).
Power Supply Base boards are designed as replacement for NFS panel range.
Eltek switch modules LSSA for selective switching of individual emergency lighting luminaires from LED to continuous operation (emergency operation to emergency operation and normal operation) depending on the general lighting
Master Box Interface Module by Esser is designed for activating and processing acknowledgement signals from master boxes and can be programmed as constant or pulsed master box activation.
USB connection kit for PC includes USB to RS232 convertor, RS485 convertor, cable and software.
USB programming dongle
Input/Output Card by Gent is a part of Vigilon System.
Vigilon Loop Card is designed to provide a powerful diagnostic tool and support a higher loop load in alarm by delivering a higher capacity for EN54-23 compliant visual alarms devices.
The fibre network card allows fast message passing to the network. The card must be plugged into the backplane of the panel or node in a dedicated slot.
ZNAC-4 notification appliance circuit (NAC) option modules are Class A conversion modules which mount to J3 connectors on the upper right side of the FCPS-24 (field charger/power supply) circuit board.
The analog loop module enables you to connect the analog loop - the esserbus® . The analog loop is configured with Programming software tools 8000 from index
Start your search with category name, product name, part number, etc.
Copyright © 2022 Honeywell International Inc.