Control Panel Cabinets, Housing & Covers
Fire control panel FlexEs Control FX18 is the basic version with 2 slots and expandable to 10 slots.
00PLEX-2 dead front panels are used in jurisdictions that require single button operation of the reset and silence functions on the fire alarm control panel (FACP).
The Honeywell wall mounting brackets are used for mounting single channel gas detector controller.
H10599/U 12-position connectors are used with IO-34-H and WEB-IO-34 I/O modules.
H10600/U 15-position connectors are used with IO-34-H and WEB IO-34 I/O modules.
The 17021 key sets are for use with NBG-12LX addressable manual pull stations.
The 17044 snap-in locks are for use with Fire-Lite® fire alarm control panels.
17045 Series Lock Kit from Notifier by Honeywell includes 5 locks from 17045 series & 5 Keys from 17021 series.
17051 Power Key Set
The enclosure has a glazed lockable door and an internal swing frame to allow easy access to the back of the sub rack.
The Mounting Frames are designed exclusively for IQ8Control C/M. These frames are also equipped for mounting of operating front and printer.
19in rack mounting kit for SZI 192 detector zones
2-way relay board for BMZ series NFS
Notifier's Power Supply is a metal cabinet with an enclosed power supply to house remote cards.
257 covers are extension cover kit for zone display module
3.9K Ohm Resistor
The DV700007 kit consists of a set of 3 M12 cable glands, 3 M12 / M20 adapters and 3 M20 locknuts
3U blank cover for 19in rack mounting
The Honeywell wall mounting brackets are used for mounting four channel gas detector controller.
ZX1/2Se retrofit 4 line display kit including display plate and overlay.
It is 4-lead resistor packs are used for field installation at supervised contacts. These resistor packs are application Accessory-Parts Used with SEC-H-600, SEC-H-201 Building Management Interface Webs.
Operator keys are for use with Silent Knight® 5208 fire alarm control panels (FACPs).
005860T surface-mount trim rings are for use with Silent Knight® 5860 remote annunciators. Red and gray options are available.
H10429/U 6-position connectors are used with IO-16-H and WEB-IO-16 I/O modules.
6700 cabinets are for use with Silent Knight® 6700 fire alarm control panels (FACPs).
Cabinets are for use with Silent Knight® 6808 fire alarm control panels (FACPs). These cabinets are red.
6820 cabinets are for use with Silent Knight® 6820 fire alarm control panels (FACPs).
6820EVS cabinets are for use with Silent Knight® 6820EVS fire alarm control panels (FACPs).
Rack Mounting Assembly for mains or gland termination kit with blank cover. Available in black and grey colour.
71252 end-of-line (EOL) resistors are for use with NOTIFIER® and Fire-Lite® fire alarm control panels (FACPs). These resistors are 4.7K ohm and 1/2W.
8 way input/output cards Provide up to 8 configurable relay outputs or up to 4 command inputs and 4 outputs.
90286 module mounting kits are required to install addressable modules on HPF24S Series power supply main circuit boards.
90474 mounting kits are required to attach an addressable module onto the control circuit board.
9600 universal brackets are for use with Fire-Lite® MS-9600 fire alarm control panels (FACPs).
The ACS-Series Annunciator and Control System provides arrays of LEDs to indicate point status, zone status, system status, and ability to perform system reset, silence, acknowledge and drill
ABS Annunciator Box provides the remote mounting for one of the annunciator module in surface mount enclosure
Flush-mount boxes are for use with Fire-Lite® ACS Series annunciators. These enclosures provide remote mounting of a single annunciator module.
Blank module dress plate by Notifier is an integral part of NFS2-640/E system. The panel is mounted in front of NFS2-640/E chassis in second or lower row of back box.
Pole-mount brackets are for use with ADPRO® PRO passive infrared detectors. They include stainless steel straps.
Key lock door for recessed mount is an accessory for emergency telephone stations.
The AM-50-PLATE is an extender plate for installing AM-50 Series amplifier.
ANN-MBRLY mounting brackets are for use with NOTIFIER® NFW2-100 fire alarm control panel (FACP) applications.
The ANN-80 annunciator is a compact, backlit, 80-character LCD fire annunciator that mimics the Fire Alarm Control Panel (FACP) display provides system status indicators for AC Power, Alarm, Trouble, Supervisory, and Alarm Silenced conditions
The Eltek mounting plates are used for mounting 2 DAs in ANX cabinets. It is used for conversion to Delta system.
Accessories are designed exclusively for IQ8Quad Series Detectors.
Adapter for telescopic rod 060426
The 6U blind cover for mounting the 4.5A power supply or 7A
The 6U blank cover for 19 rack mounting.
The Rack Blank Cover with Printer provision (Adapter plate and cover).
Additional housing for NOTIFIER-BMZ normal depth
Address units are used for connection of conventional detectors for a Quad loop. The device contains 1 pcs. Alien transponder, and DC / DC converter. 24V DC input have back up battery supply.
The Addressable communication module is a category B module for CMSI SensES and CMSI 8000. The communication module is a rack version module. The module is supplied with esserbus communication plus.
Adjustable bracket for RIV-601/F
Amplifier Module is Independent backup amplifier protection re-routes power to a backup amplifier in the event of a primary amplifier failure.
Analog Control Panels are not only control panels, they also includes advanced fire detection protocol and advanced communication with field and technology.
The ID3000 is a flexible, modular control panel, built from various option modules. Each module is supplied with required mounting screws, connection cables, washers etc. and installation instructions.
The Annunciator is an attractive surface-mount backbox for mounting one ACS Series Annunciator.
Annunciator Bezels are red and for use with Silent Knight® 5860R remote annunciators.
Annunciator Flush Box is exclusively designed for mounting annunciator modules.
The Annunciator Keyswitches are used to enable/disable the NCA-2 keypad.
The Annunciator Surface Box provides for the remote mounting of one annunciator module in a surface-mount enclosure. Knockouts are provided for use with 1/ 2" (1.27 cm) conduit. The annunciator mounts directly to the ABS-1B/C without a dress plate.
Heat conductive compounds are for use with Aquastat® temperature controllers. They improve heat conduction in immersion well applications where the bulb does not fit tightly.
Audionet-MX system rack mount connection panels are used for connection of 10 microphone bases.
Avoor Din Rail Mounting is suitable for Esserbus alarm unit type 808623, voltage converters type 781337/781336 and fuse module type 382040.
B-Sized marine cabinet comes with 12 gauge steel door and 6 gauge black box. These cabinets are available with a Notifier logo.
Snap-in locks are for use with Fire-Lite® BG-8 Series manual fire alarm call points and prevent restoring the activated alarm to normal except by use of a key.
The Backbox for Programmable Universal Zone Coder(UZC-256) is used when the UZC will not fit in panel enclosure.
IP base adapter for extreme environmental conditions.
The basic module carrier forms part of the fire alarm control panel's basic structure.
Battery Box for Batteries Larger than 25 AH
Battery Expansion Housing in Pro-Box.
JBP2-4 Battery Panels are required for each cabinet assembly that mounts batteries and/or a power supply in the lower position of the cabinet.
Battery box or mounting enclosure which has Size 500 x 500 x 185mm (H x W x D).
Bezel For Pearl Back Boxes are flush mount dress rings offers a practical way of flush mounting the Pearl panel.
Extended Bezels are double extended bezel with semi-flush mount bezel for double extended height back box
Semi Flush Mounting Bezel for ID51, ID61, ID2000 and ID3000 standard back box.
Blank dress panel provides dead-front panel for unused tiers; covers DAA2/DAX series or AA-series amplifier.
Blank Module Plates by Notifier are cover unused module positions in an annunciator backbox also included four stand offs which allows option modules to mount behind the black front, or inside the cabinet.
The Blind Covers Over Setpoint Wheel are spare parts for T7460/T7560/T7270 wall modules.
Blind plate for expansion cover type ECK-B
Notifier network options
Branded clip accessories are used for Trend open network node such as TONN8.
C4 Cabinet Backbox are available in black or red. This selection provides a stylish combination to accent the décor of the finest lobby setting.
Cabinet assembly consists of two basic parts a backbox and a locking door. Backbox has been engineered to offer ease-of entry for the installer. Cabinets are available in either black or red, with or without windows.
CAB-4 Series Semi-Flush-Mount Accessory Trim Rings are used for mounting accessories in Notifier's Fire Alarm Control Panel cabinet assemblies.
DR-B4 is Two Tiers, “B” Size CAB-4 Series Cabinet for NOTIFIER Fire Alarm control panels.
CAB-4 Series Cabinet for NOTIFIER fire alarm control panels are fabricated from 16-gauge steel
CAB-M series marine enclosures are designed to house the AFP-200, AM 1010 or AM 2020 intelligent fire control panels in marine shipboard environments were dirt, dust, oil, water or other contaminants are present.
CAT 30 Lock with Key
CB-1 Chassis Bridge provides a bridge between CHS series chassis.
The Honeywell General Purpose Cabinet includes separately ordered Rough-in Ring, Subpanel and Door Assembly with a lock.
This Cabinet selection provides a stylish and a classic accent to the décor of the facility lobby and the reception areas. The flexible back box design allows you to easily install and maintain the cabinets in a variety of building options.
Cabinet Assembly is required for IFP-50 and 50PT Addresssable Fire Panel.
Clamp with integrated 6 mm dowel for fastening the sensor cable to the ceiling. No screw or extra dowel required. Approx. 50% time savings when laying.
Polyamide Cable Gland to increase the housing protection level and provides strain relief to the inserted cable
Cable managed wall mount bracket is accessory for AVH Series outdoor camera housings.
Calibration wrenches are for use with T991, T631, T675, T678, T6031, T475, T4031, T4054, T6054, and T6064 remote temperature controllers.
Case back with low installation depth suitable for holding fixture of front unit inclusive electronics for LED and LED / LCD keypad
An external printer may be connected to the control panel during commissioning
Honeywell’s Fan Coil Thermostats are used in individual rooms or zones in buildings. The thermostats are designed for two and four-pipe fan coil units.
Communication Modules are use in the ZX series intelligent multi-protocol fire alarm control panels & These optional modules add optically isolated communication ports to the ZX series control panels
Compact 24hr inner door assembly
Connection Base is a SMILE mounting accessory for panel models.
Battery Holder for Flex Control Panel includes holder / expansion rivet for the PS connection module (PSM).
Control panels installation boxes are used for flush mounting installation, holding fixture of all MB-secure keypads and installation into hollow walls. The flush mount installation boxes replaces the case back.
Control Panel Cabinet Keys are for use with Silent Knight® 5000 entry system control panels. These keys are made of metal.
Control units are required for operating the emergency doors. They have indicator LEDs for the models with a relay and piezoelectric alarm warning siren. Unlocking can be done with a key or by breaking the button glass.
Cover for extensions of the control panels or for the additional housing
Cross-duct retro-reflector mounting plate long range accessories are used for searchline excel cross-duct infrared gas detectors.
D4 Series Cabinets are designed to house Gamewell-FCI’s, E3 Series® Classic Emergency Voice Evacuation AA Series amplifiers, Honeywell Power Products’ Chassis Power Supplies
D4 Series Cabinets backboxes are engineered so that it is easy to install and maintain and The key-locked door includes a pin-type hinge, two keys and hardware that are used to mount the door to the backbox
DEZ 9000 alarm receiver plates includes front and mounting plates, these plates allows receiver modules to be integrated in a 19” cabinet.
EDM200E-DIN are DIN rail mounting clip for M200 series addressable input/output modules.
Esser’s adaptors for DIN-rail mounting are suitable for Esserbus relay units, Esserbus optocoupler units.
DP-2 dead front dress panels are for use with Fire-Lite® 411UDAC fire alarm control panels (FACPs). They restrict access to the system wiring but allow access to the membrane switch panel.
DP-9692 dress panels are for use with Fire-Lite® MS-9200UDLS fire alarm control panels (FACPs). They mount to the inside of the cabinet and restrict access to the system wiring while allowing access to the key panel.
DP-ES-R dress panels are for use with NOTIFIER® fire alarm control panels (FACPs). They mount to the inside of the cabinet and restrict access to the system wiring while allowing access to the key panel.
The DS 8800 Mounting Sets have been provided for DS 8800 in intrusion detection central unit 5008.
The DVC Series Dress Panels by NotifierR are part of Digital Voice Command or DVC.These dress panels play the role of mounting the DVC with CA-1 chassis when CMIC-1 microphone is not used.
DX Spare Keys are used for DX series Keyswitch kits and are available in a pack of 5.
DX-M Control Panel Covers are available with printer slot
The DXc Blank Covers are a part of cover kits for DXc series control panels.
DXc custom key plate cover kit accessories are used to replace the blank cover supplied with the DXc2/4 control panels or used with the extension back box.
The Morley IAS DXc Flush Bezel Kit used for Morley IAS DXc2 or DXc4 panel and the kit includes additional extension back box. Extension box is used to accommodate larger batteries, relays or other equipment.
DXc replacement door is available for DXc control panels. This replacement door is fits with all three variants of the panel, DXc1, DXc2 & DXc4 and is supplied complete with display PCB, fascia label, ribbon cable and lock.
DXc1 rack mounting kit accessories are used for DXc1 one loop fire alarm control panels.
Deep Extension Back Box Kit includes deep back book with extra depth for additional battery space. The box has an extra fine texture RAL 7021 finish.
Delta Compact Drawing Cabinet can be used as a microphone cabinet for DCSF in Compact design. The drawing cabinet has the same physical dimensions as the Delta Compact.
The cabinet is adapted to A3 binders and used as a basis for binders and drawings.
Design Pendulum SB is available in white colour with 500mm size.
FlexES display and operating panel brings new features so-called night-mode design featuring a completely smooth, easy-to-clean surface experience. The 5.7" graphic display can indicate more than just a customer-specific logo in normal mode.
Release button for hold-open system in surface-mounted and flush-mounted versions
Double board enclosure for NX4IN, NX4OUT Hybrid Access Control Panel.
Drawing Cabinets are delivered with Swedish print. Used for plant documentation together with BSX100
DPA-1 is the Dress panel that can be used with the CA-1 chassis when configured with a DVC, DVC-KD, and CMIC-1.
Dress panel for top row in cabinet with CPU2- 3030D installed.
Dummy cover with 5 HU to cover the heavy-duty drawer (only for FlexES Control racks for Power Supply Unit and batteries) incl. mounting material with two handles.
Dummy plate is used to install fire stations DCSF12 or DCSF1 in the upright cabinets
Dummy cover for heavy-duty drawer PSU (5 HU)
Dummy cover used for covering free installation space in rack mounting cabinets.
S4-COVER-REMOVER is a Spare Adaptor used for Dust Cover Remover.
E-Line cover and labelling set consists of 5 covers and labelling sheet for mounting in the automation control cabinet.
The E3 Series cabinet assembly is a compact, wall-mounted enclosure
E3 Series System by Gamewell-FCI is a modular design that allows a wide range of configurations to form an integrated, distributed fire alarm system. Trim kits are the optional accessories of E3 series cabinets of sizes A, AA, AA1, A2, B, C, D.
Gamewell’s E3 series AOM-TEL plates are used with the E3 Series® LOC-TEL local operating consoles.
E3 Series B Cabinet features compact assembly that allows a wide range of configurations to form an integrated, distributed fire alarm system
The E3 Series System is a modular design. It allows a wide range of configurations to form an integrated and distributed fire alarm system.
E3 Series cabinets backboxes includes mounting patterns to aid the installer in arranging and securing the sub-assemblies to the backbox.
The E3 Series Transponder Module Mounting Plates are used in E3 Series Cabinet. E3 Series Expandable Emergency Evacuation System by Gamewell-FCI offers several cabinet size options.
Enclosures for E3 Series® "D" Cabinet which contains fire fighter’s phone handset, microphone, optional modules to meet the facility operation requirements.
Backbox enclosure assemblies are for use with Gamewell-FCI® E3 Series® cabinets (size B). These assemblies are black.
Battery boxes are for use with Gamewell-FCI® E3 Series® cabinets.
The E3 Series System is a modular design that allows a wide range of configurations to form an integrated, distributed fire alarm system. These cabinet options allow for sturdy and modern installations.
The E3 Series® Cabinets are used for E3 Series® Expandable Emergency Evacuation System by Gamewell-FCI. These cabinet options allow for sturdy and modern installations. The E3 Series cabinet assembly is a compact, wall-mounted enclosure.
Replacement locks are for use with Gamewell-FCI® E3 Series® cabinets (sizes A, B, C, and D).
Single size blank plates are for use with E3 Series® cabinets.
Command center mounting plates are for use with Gamewell-FCI® E3 Series® cabinets (C and D sizes are available).
The E3BB is an Inner Door Mounting Cabinet for E3 Series® of Gamewell. The E3BB cabinet assembly is a compact and wall mounted enclosure.
Inner door panels are for use with Gamewell-FCI® E3 Series® cabinets. These panels are blank and double size.
Intelligent loop module mounting plates are for use with Gamewell-FCI® E3 Series® cabinets (B and C sizes are available).
E3BB backbox enclosure assemblies are for use with Gamewell-FCI® E3 Series® cabinets (B and B-Slim sizes are available). These assemblies are red.
E3BB remote enclosures are for use with Gamewell-FCI® E3 Series® cabinets (A, A1, and A2 sizes are available).
E3 Series® Expandable Emergency Evacuation System by Game well-FCI offers several cabinet size options. E3 Series System is a modular design that allows a wide range of configurations to form an integrated, distributed fire alarm system.
E3BB-BD enclosures are for use with Gamewell-FCI® E3 Series® cabinets (size D). These assemblies are black.
E3 Series® Cabinet by Gamewell-FCI offers a variety of cabinet options to house either the E3 Series or S3 Series fire alarm control panel systems.
E3ID2 inner door assemblies are for use with Gamewell-FCI® E3 Series® cabinets (AA, B, C, and D sizes are available).
TR-6-R trim rings are for use with Fire-Lite® ECC-RPU remote page units.
EMPERTECH Conference System is to satisfy the customer’s needs to complete the one-stop solution for end users. Each of the Empertech conference system is catering to different specific applications from small to large conference environment.
EQBB backbox assemblies are for use with NOTIFIER® EQ Series cabinets. These assemblies are available in red or black and feature two, three, or four tiers.
EQDR door assemblies are for use with NOTIFIER® EQ Series cabinets. These vented doors are available in red or black, and feature two, three, or four tiers.
Emergency File Depot DIN A4 are 4 holes and on the front side 4 bracket hooks. For the installation on any underground are to set out 4 flat head screws (max. 4mm Ø).
Empertech Ceiling Cameras can be easily attached on the ceiling. They are designed by the full-featured, high-performance digital DSP and assuring stable capability.
Front door mounting frames are for use with Excel Web II programmable universal BACnet® building controllers. They are sold in packs of ten.
Expansion housing for DXc series BMZ
Extended Back-Box Kits are double extended back box kit with double “extended height” back box powder coated in RAL 7021 extra fine texture. Includes power in connectors. Will hold batteries up to 17Ah.
Extension / Large Back-Boxes for new Pearl installations, Surface or Flush mounting, includes cover and space for 17Ah/38Ah batteries.
Morley - IAS' Extension Back Box Bezels are flush mounting bezels that fits a DXc1 panel with additional extension back box.
Extension back boxes for existing surface mounted Pearl installations. They includes cover, panel dress plates and space for 17Ah batteries.
Extension Chassis Kits includes extension chassis with LED display board for zones 17 to 80 to indicate fire and fault / disablement / test.
Extension Module Carrier is a module carrier in plastic mounting tray for up to four modules with plug-in terminals. The modules automatically lock when plugged in and can be exchanged without using any tool.
Extension Module carrier in plastic mounting tray for up to four modules with plug-in terminals. The modules automatically lock when plugged in and can be exchanged without using any tool.
Sheet steel housing for surface and flush mounting to accommodate fire brigade route maps. Door opening by the fire brigade lock.Prepared for half cylinder installation.
External HMI Base is an extra part designed with a metal plate for hand-held use. It is equipped with two screws and two dowels.
External mounting enclosures consist of mounting bracket IPBRKT and screws.
FIOS mounting kit for DCSF1/12 call station
Fan Unit Controller from Honeywell is compact in size.
Fascia is used for NF50. It is a five button version.
Filter covers are used for air intake, including filter mats and fastening material Filter cover for use in areas with increased contamination
Fire & MNS Systems by Gamewell- FCI are allows a wide range of configurations to form an integrated, distributed fire alarm system in combination with the audio evacuation for use with both Fire and Mass Notification functions.
Fire alarm computer FlexES control rear housing panels 2 are used for vertical installation of modules.
Fire Alarm Control System Cabinet Only for an IFP-2000 scalable addressable fire alarm control system, red.
Fire Alarm Documents Cabinet (FAD) may be used as a storage box for both printed and digital documentation, enabling one to store the system’s test and certified inspection documents, service records, manuals and AS built drawings
Fire Fighter Key is used for drawing cabinets, control panels etc.
Fire protection housing for the installation of a fire alarm control panel in accordance with the requirements of the German Fire Conduit Installation Directives (MLAR and LAR)
Fire System Document boxes are designed to complement any life safety system. The robust, lockable steel enclosure offers safe storage and fast access to essential documentation.
Fireray 3000 Controller Back Box is an accessory of End-to-End Optical Beam Smoke Detector
TR-1 trim ring assemblies are for use with Gamewell-FCI® Flex 4-zone fire alarm control panels (FACPs). They allow semi-flush mounting of the cabinet. Red and black options are available.
TR-CE trim ring assemblies are for use with Gamewell-FCI® Flex six-zone fire alarm control panels (FACPs). They allow semi-flush mounting of the cabinet. Red and black options are available.
FlexES Control Network Card Essernet Modules have been designed to work on Token-Passing protocol with loop topology, interruption and short-circuit tolerance.
Flush Bezel Kits by Honeywell are covers can be purchased to suit your needs and include a blank cover, Customer key plate and 80 Zone LED expansion cover.
Flush Bezel kit is used in DXC1.
Flush Fixing Kits are flush mounting plate for Gent Xenex conventional fire detection panels
Flush Mount Dress Rings are installation kit for pearl smart fire alarm centre which includes 19in kit and finishing edge.
Flush Mount Installation Box are used for flush mounting, holding fixture of all MB-secure keypads and installation into hollow walls. The flush mount installation boxes replaces the case back.
The (VIG-24-FLUSH) Flush mounting kits can be used for Gent Vigilon Plus VIG-24 fire alarm panels and network node.Control Panels may be semi-flush mounted using a semi-flush surround.
Flush Surround for Gent Compact Panel
GW Cabinet is an accessory cabinet used for mounting GWCZM400 zone expander or GWIOM-410 status display module.
Replacement Terminal Covers - Gateway (Small)
Extended Terminal Covers - Gateway (Large)
The D4 Series Cabinets are designed to house the Gamewell-FCI’s, E3 Series® Classic Emergency Voice Evacuation AA Series amplifiers and Honeywell Power Products’ Chassis Power Supplies. These cabinets are constructed from 16-gauge steel.
Glass Door Kit for DX control panels M and L size
Graphic Annunciator Dress Plates are used when the 10" graphic display is mounted in the top row/except top row of a CAB-4 Series cabinet.
HAWK 8000 Clips are used in HAWK 8000 spare parts.
Thermostat calibration tools are for use with HP970/972 pneumatic humidistats.
HPTCOVER transformer enclosures are used in applications where the installation requires a plug-in transformer to be securely affixed to an AC wall outlet.
Heat-detecting cables fastening clips are used for meters to ensure the recommended distance from the surface approx 2 cm.
High Security Main Cover Kit by Notifier includes the front panel, high security screws. The High Security Main Cover Kit comes with an extra fine texture RAL 7021 finish.
High power PoE injector and PoE PSU within a C-Enclosure with front tamper and fixings for 1xPW6101 Access Control board Enclosures for PW6101 Family Intelligent Control SystemPW-6101 Intelligent Controller Board, POE, and embedded Ethernet.
The 797-062 is a Semi flush mounting kit for ZX5(S)e control panel.
Housing flush mount, white
Housing for up to six IQ8FCT XS
Housing surface mount, white
The Notifier zone-led options can be installed in the main control panel and is connected via a flatcable to the main unit
ID3000 series orientation drawings OR cabinets are designed with lock that opens with a standard fire extinguisher key, left- hung door 4 mounting holes on the back and holder for OR binder.
Semi Flush Mounting Bezel for ID62 available in grey and black colour.
IDP-ACB module cabinets are for use with Silent Knight® IDP-Zone-6 interface modules. They have a built-in chassis that will accommodate one or two modules.
Flush Mounting Bezel for IDR repeaters.
Enclosure for IFP-2100 Series analog/ addressable fire systems.
Kit for integrating an IQ8Control fire alarm control panel into an IGIS-LOOP.
INCC Inner Door for E3 Series Cabinets.
CAB-5 Series cabinets for INSPIRE N16X Series to build a custom panel to fit your application and scale as the system grows.
INX backboxes are for use with Gamewell-FCI® INX intelligent network transponders. These enclosures are used to house the transponders for E3 Series® cabinets (B size).
Replacement Screw Terminal Blocks - Smart IO
Replacement Small Terminal Covers - Smart IO
The IQ8Control battery monitor module are inserted between the 12 V battery to be monitored and the associated connection contact of the basic module of the FACP.
IQ8Control extension housing for multiple appliations
IQ8Quad Detector Demo Case is a Demo Case with a built-in IQ8Quad detector with integrated alarm device for demonstrating the whole range of multi sensor functionalities.
IQ8Quad label plates have been designed for detector base IQ8Quad.
IQ8Wireless cover for wireless interface, red and white
IRM IP30 terminal covers are used with Comfort Point® open room controllers. Terminal covers are available for large and small housings.
Honeywell’s Controller manages detection, notification and extinguishing functions. It can integrate with process safety systems and peripherals through multiple protocols.
Installation material dummy units are designed for 19” switch cabinets and headroom units.
Installation support for round reed contacts with flange. The support can be mounted to any desired height by means of spacer tubes.
The Installation Support For Recessed Reed Contact is suitable as mounting aid for aluminum and hollow profiles for embedding or height compensation.
Intelligent Fire Integrator™ Enclosure is designed for housing components.
Intelligent System Spare Parts are text insert label kit for intelligent addressable fire alarm panels
Intelligent systems installation kit spare parts including slide-in label are used for pearl fire alarm control panels.
Intelligent systems lock and key set spare parts are used for NF2000/3000 fire panels.
Intelligent Systems Surface Mounting Box Spare Part is available in white colour.
IntelliKnight® IP communicators for monitoring of Silent Knight® fire alarm panels.
The NFS-320 intelligent Fire Alarm Control Panel is part of the ONYX® Series of Fire Alarm Controls from notifire.using NFS-320C, an optional ACM Series annunciator can be mounted in the same cabinet.
Interface Enclosures are generally supplied without enclosures. A range of enclosures are available if required to house them.
Vigilon’s range of loop powered interfaces offer a comprehensive range of connectivity options with critical plant and other safety systems
IPENC external enclosures are for use with NOTIFIER® IPDACT internet monitoring modules. Includes IPBRKT mounting bracket. Red and black options are available.
Ivory faceplates are sold in packs of ten. All faceplates are unmarked (without logos).
KNOB replacement knobs are for use with TR23 wall modules.
KeyMate™ key fobs contain advanced passive proximity technology small enough to fit on a key chain.
These copper wells and inner filters are for use with LP914 pneumatic temperature sensors.
Duct mounting clips are for use with LP915 pneumatic temperature sensors. They are used for averaging capillary.
Knob and scale plate assemblies are for use with LP916 pneumatic thermostats.
Label for release key
Large Interface Enclosures are used to mount S4 Interface modules. It consist of Plastic Box with dimension 245mmx227mmx77mm.
Lever lock with 2 keys (No. 801)
Lid Plate Support is required for IM2700/IM2720/IM2750 Case.
Locking System Stickers are required for installers.
The Loop Powered Enclosures as the name suggests are metallic enclosure with 20 and 25mm knockouts for Vigilion's Loop Powered Intefaces.
Honeywell MAXPRO Access MPA1 significantly decreases installation time and costs while delivering a secure, remotely managed access control solution, standalone or integrated with MAXPRO Cloud.
MULTIMOD-BRKT mounting brackets are for use with Fire-Lite® ROME Series relay option module enclosures. They are used to install the modules inside the fire alarm control panel (FACP) backbox.
MVC-80-AC1 terminal covers are for use with Excel Web II programmable universal BACnet® building controllers. They are sold in packs of ten.
Includes moulding, hinges for user interface door, push clip fasteners, Notifier label and hex fixing tool.
3U Rack Blank Cover comes with mains/gland termination.
The Mar Fire Detection Unit is a Detection Control Unit in rack configuration able to house up to eight MAR2 / DM cards inside each of which can manage up to four sections of digital heat-sensitive cable, having maximum length of 5,000 meters.
Metal housing for NOTIFIER ring bus modules
Midas® Gas Detector
Rack Mounting Assembly for mimic driver kit available in black and grey colour.
Module housing for top-hat mounting rail
Moisture Protectors are permanent anti-humidity protectors with test input. They are adjustable on type 2 heads.
020-835 is a Spare key switch and keys for Morley-IAS repeaters.
The Key and cylinder kits are for DX CONNEXION control panels that allows the user to access level 2 function keys without using a password.
Mounting Bezel Kits are of stainless steel and are designed to use with ID2000 and ID3000.
Mounting Brackets are available in stainless steel material.
Mounting Kit contains 24 cage nuts, screws and washers.
Mounting Rails by Honeywell are vertical or horizontal mounting rail for cabinet frame with or without hinged frame.
Mounting set is used for mounting the air duct construction set to round and/or insulated air ducts.
Mounting bracket is used for alignment of the industrial heat- and flame detectors UniVario. Simple installation with base Part No. 783313.
Mounting kit for ALR microphone Part No. 581316.
Mounting rail for FACP
Mounting rail set for connection terminals
Multi-mount metal enclosures are capable for housingmmX-10ME, CMX-10RME or MCX-55 modules.
The One System IO-module is suitable for digital connection of One System locks with Hi-O technology.
Notifier Retrofit Mounting Kit is used for mounting the NCA-2 Network Control Annunciator to a DPDISP dress plate.
Plastic enclosures are for use with NETAXS-123 hybrid access control panels. They are made of high impact plastic and contain wiring access holes/knockouts.
Display Assemble Kit for NF2000 includes a display plate (2× 40 LCD).
Display Kit for NF300. It Includes display plate with 240 × 60 pixel LCD and assembly kit.
NF3000 Intelligent Fire Panel Kit includes equipment kit with 2 loops, Dutch/ French language kit, power supply unit kit, standard back box kit, main cover kit.
NFS2-3030 is an intelligent Fire Alarm Control Panel (FACP) designed for medium- to large-scale facilities. CPU2-3030ND is one of the main component of this system. It is also known as display of the system.
Replacement door used for mounting ACPS-610 (E) in a CAB-PS1 cabinet when replacing ACPS-2406
NXENCM metal enclosures are for use with NETAXS-123 hybrid access control panels. They contain 19 wiring access holes/knockouts.
NANO-FLUSH from Gent is a Flush Mounting Bezel which has been designed for the Gent Nano-24 panel. The bezel will cover any imperfections in the wall when this has been cut to fit the panel.
The backbox has been engineered to provide ease-of-entry for the installation of the fire alarm control panels.
The Battery Plate used to cover battery and power supply when lower position is used in backbox.
TR-ABS is a Back Boxes which provide an enclosure for remote mounting it can be surface or semi flush mounted.
ONTRUIMINGSALARM Lables are for 5500 series with "ONTRUIMINGSALARM" text printed on the lable
Backbox by Notifier has been engineered to provide ease-of entry for the installer.
OmniAssure mullion to wall switch adapter plate used for MultiSmart Readers.
Operating device Touch Center plus accessories includes metal box for masonry mount of LED/LCD/touch keypad, FM-frame, console house top, console house base, touch bezel, case back deep, flush mount installation box.
BB-XP is an Optional cabinet for one or two modules.
ID61 & ID62 Replacement PCB Assembly Kit includes Lcd and Membrane.
PCD1 housing covers are used for PCD1.M2xxx series modules. They have an overlay that can be individually designed.
The PCD2 expansion module holders can be connected to the Saia PCD2.M4x60 modules which makes it possible to connect up to 64 I/O modules or 1023 digital I/Os.
Saia PCD2 Housing Covers are required for PCD2.C2000 without logo.
Saia Burgess empty module housing for unused PCD3 control panel I/O slot.
PCD3 housing covers are used for M5xxx and M6xxx series controllers.
Slot covers accessories are used for unused PCD3 I/O slots.
Wall mounting kit accessories are used in 10inch PCD7.D410VT5F programmable web panels.
Wall mounting kit accessories are used in 12inch PCD7.D412DT5F micro-browser based web panels.
PRO22CVT1 data converters serve as an interface located between the computer and the PRO22IC intelligent controller. The device converts the RS-232 data coming from the serial port on the PC into RS-485 data.
PVC White Plates suitable for installations where it is required smoke detection in ambient.
The PW Series C Type Cabinet provides fixings for two PW6101 modules with built-in 13.8V DC power supply and tamper switch.
Pearl Software is the programming software for pearl smart fire alarm centre.
Plastic washers are available in white or silver colour.
Power supply units ZG4 empty housings are available with lock insert. ZG4 housings are used for integrating the power supply/charger unit 012170.
Power supply extension for DXc1-M and DXc2-M
Protected Area is required for the protection of up to four-core communication, data and other lines with common earth, against surge voltage. It is suitable for the communication interface of I and C, electronic security and fire alarm systems.
Q651 switching subbases are for use with T6051A heavy duty thermostats. These subbases provide positive 'off' switching of the system.
Flush Backbox for RAN-7100
RBB surface-mount accessory cabinets can be used if the main control panel backup batteries are too large to fit into the main control panel cabinet.
Setpoint knobs are for use with RP920 pneumatic controllers.
Rack cabinets pair of brackets are used to support amplifiers, matrices and audio equipment.
19in-9 US rack container, complete with tamper, for input / output peripheral cards such as concentrator box.
Rack Mount Kit for Pearl panel enables the Pearl to be mounted in a 19in rack.
Notifier Rack Mounting Assemblies are 6 U 19in adapter plates and covers used for standard chassis, printers and 256 zone display modules.
Rack mount kit fits a DXc2 panel or DXc4 panel.
Rack cabinet 19” with swing gate for IQ8Control
Esser-eff alarm is a hold-open systems for fire barriers consist of a release device and a hold-open device. Hold-open systems are used to delimit buildings and objects in closed fire compartments to protect people and property.
Reducing Frames are accessories designed for mounting panels.
Modules with redundant line monitoring and voltage booster are used for fire alarm control panels. Modules enables the connection and monitoring of the remote power supply unit PSU7A according to EN 54-4.
Surface-mount backboxes are for use with Fire-Lite® ACM-8RF relay modules.
Remote annunciator trim ring accessories are used for surface mounting of RA-2000 / RA-2000GRAY remote annunciators.
The Floor mounted only back box with extra depth for additional battery space. Powder coated in RAL 7021 extra fine texture. Includes power in connectors. Will hold batteries up to 78Ah. Compatible with PSU7A (020-579).
Remote Fire Alarm Panel Cabinet Only is an accessory of RFP-2100, black.
The remote reset button is an accessory designed for Autonomous Detector Trigger that is used to detect locally from one or two identical sensitive elements related to fire and to ensure direct control of a controlled organ.
Replacement Door Lock is used with GFPS AND GWF410 Cabinets.
Replacement Lock is required for LCD-7100 in 3/4 inch size.
Replacement Moulding/Cover Plate for Xenex Control Panel.
The NF30/50-CAB-A1 replacement PCB assembly Kit incl. all electronics for the NF30/50 series panel on the PCB, Liquid Crystal Display (LCD), fascia membrane and language inserts, supplied as a replacement spare kit.
The Retainer used for 50Kg / 445N fire door. It is available with ferromagnetic plate articulated, without box and with release button.
Room temperature sensor's spare parts are used for models T7460 and T7560 room temperature sensor wall modules for EXCEL 5000 controllers.
S-Quad Duct Mounting Brackets are designed for the S-Quad Duct Smoke Sensor. They are available to mount the detector on circular and insulated ducts.
The Schneider electric’s S3DEX steel enclosures are resistance to external impacts. It has structured finish with epoxy-polyester powder paint. It has removable and reversible door with simple reversal linkage. Door has polyurethane sealing gasket.
SCS12 Traffic Cuffs are orange polyester mesh with yellow North-Brite™ reflective material with velcro closure.
SK-2190 accessory cabinets are for use with Silent Knight® SK-5217 zone expanders.
SK-NIC-KI accessory install kits are for use with Silent Knight® SK-NIC network interface cards.
The Gamewell-FCI SKF-SRD are System Record Documents Cabinet. This cabinet is constructed of durable 16 gauge steel with a solid piano hinge and key lock.
SMB500 surface-mount boxes are for use with System Sensor® modules when flush or recessed mounting is not possible.
SMC SenTRI FOUR Flush Surround is 4 loops control panel for analogue addressable fire detection and alarm system.
Saia PCD2 Housing Covers are required for PCD2.M5x40 without logo.
Secondary terminal cover accessories are used for Trend IQeco38 controllers.
Semi Flush Mounting Bezel for ID50 & ID60 available in grey and black colour.
SenTRI 2 inner door assembly used as spare for SenTRI 2 control panels.
SenTRI 2 outer door assembly used as spare for SenTRI 2 control panels.
USB to RS232 (upload/download lead) serial port to USB converter
Series Cabinet Door assembly consists of two basic parts, backbox and a locking door. Series Cabinet Door assembly has “D” sized cabinet with solid door.
Service drawer (1 HU)
Single-Pole Double-Throw Switches are availabe with 1-18GHz frquency. This switches can be screened to the salient characteristics of MIL-STD-883.
Sleeve Junction Tubes are accessory for FAAST system and they are available in red colour with outer diameter of 25mm.
The Smile Connect installation kit is used to perform the initial setup of a SCN-10. The installation is carried out directly with a PC. After connecting the PC using the SCI-10 Adapter.
The Spare Allen Key is a spare part of Sounder-strobes.
Spare key for fire alarm control panels
Spare Lock and Key is required for 1 key only.
Spare Pearl Door Assemblies are spare door modules for pearl smart fire alarm centre.
VIG-FLUSH-SS is stainless steel flush mounting kit for Vigilon main control panel.
The Swivel Bracket is available in stainless steel with swiveling ball joint to hold the SPECTREX MINI series detectors.
Standard Back Box Kit includes a basic back box powder coated in RAL 7021 extra fine texture and power in connectors. Will hold batteries up to 12Ah. Compatible with internal PSU3A or external PSU7A.
Status Indicator is int