Switch and Wiring Loom are designed as spares for SAFE which is introduced as an engineered solution for your building and to avoid the risk of generating multiple false evacuations.
Classic 19 ”rack cabinets are designed to efficiently manage the distribution and interconnection of the equipment located inside.
The Mounting Frames are designed exclusively for IQ8Control C/M. These frames are also equipped for mounting of operating front and printer.
Large Bore Red Pipe is of 3m Length and have a diameter of 25mm.
25mm Red ABS Self Draining Water Trap
25mm/10mm Compression Adaptor Tee comes under accessories of pipes and fittings. This is used for 2 capillary tubes.
The 3-gang electrical boxes are 5.556 cm deep and intended to be use in semi-flush mount applications.
The 300 Series conventional relay bases are designed to provide interfacing between a Series 300 detector and 24V fire control panels or power supplies that require an external contact to activate an ancillary piece of equipment.
Base is the integral part of LED remote indicator.
The detector base is an accessory designed for LED remote indicator.
The base is an integral part of the LED Remote Indicator.
The 34000 S-Quad adapter base provides a simple and cost effective solution for the replacement of ageing 34000 range sensors with current S-Quad Sensors.
The aluminium housing with rear end along with bracket features a canopy and thermostat control. It also has adjustable wall support.
The aluminium housing with rear and front made with techno polymer along with bracket features a canopy and thermostat control.
Bracket and housing is designed for difficult climatic installations, particularly suitable for installations in marine, industrial or chemical environments.
4 trim ring and snap-in mounting clips for IQ8Quad detector base
530-ABR Clamp for Holding Pipes.
The support plate is designed exclusively for CMSI 8000 rack.
705 HT Series of Flammable Gas Sensors
8-fuse-card
F-A3384-000 air filters are replacement filters for 8000 Series detectors. These filters combine a 30 micron filter element and a plastic housing into a single module that reduces service time and labor.
Anchor plates in combination with holding magnets are the integral part of an automatic door arrester system.
801824 Remote Indicator is Red prism illuminated by 4 pulsed LEDs for operation on esserbus and esserbus-PLus to optimize energy consumption
A2402A are Plastic Clamp Set made up of Polyamide/Stainless Steel Dowel available in pack of 100.
ABS-Bögen und Winkel als Zubehör für Ansaugleitungen von Ansaugrauchmeldern.
ABS Rohre mit einer Lieferlänge von 3m und einem Außendurchmesser von 25mm
ACCESS BEAM CONV/L REFLECTOR 75M-100M
Safety power supply of 24V designed in a rack is an integral part of the power supplies range introduced by Esser.
Safety power supply of 48V designed in a rack is an integral part of the power supplies range introduced by Esser.
The power supply designed in a C85 box and is equipped with four 12V DC / 38 Ah batteries.
The power supply designed in a C85 box and is equipped with two 12V DC / 38 Ah batteries.
AP Base Conduit Adaptor are base adapter accessory for B401DG and B401DGR for tubes of 18 and 20mm.
Honeywell Accessories for Pressure Switches / Transmitters Syphons is use for high temperature, stainless steel and circular.
Honeywell provides acoustic typhoon alarms are used together with solenoid valves and are powered by compressed air.
Adapter Kit for Recessed Mounting Speed Dome.
Adapter for Sensitron Gas Detectors. It allows the right quantity of gas inlet to flow to the detector.
Adapter for the AGILE HWKIT
Detector Base is an integral part of the 800 System Devices.
Adeva standard bases are used in FCOT321 intelligent multi criteria photoelectric smoke detector.
Adhesive Foot for Printed Circuit Board.
Adjustable mounting bracket
Air Duct Detector Accessory Filter cartridge for air duct module 781443 for use in unclean environmental conditions.
Plastic Clip for Air Flow Reducers
Air filter
Cage is designed exclusively for Alertus© Alert beacons.
The analogue heater base models are two wire heated base designed to be used when environmental conditions mean frost or condensation may build in the detector’s chamber and cause false alarms.
Angle Brackets by Gent are designed for use in areas where beam detector will not be installed to a vertical surface, or where the beam path is not perpendicular to the installation surface.
Anti-Climb for Tower Column. It provide one for each column.
Anti-Removal Kit for NBMHP-VAC Series barriers.
Apollo Detector Discovery Baffles are used to direct the sampled airflow through the point detectors housed in the ICAM IAS aspirating smoke detector.
Articulated Steel Support for fixing the antenna to the wall.
Aspiration Adhesive Spray are used to join the pipes / sleeves / bends together in an aspiration system.
Aspiration reducing film sheet accessories are used in aspirating systems and they are available in various size such as 2.0mm to up to 6.0mm.
Aspiration reducing film sheets are required for smoke-extraction openings. The foils are for tapering the drill holes in the intake manifolds and prevent any increased development of noise in the operation of the aspirating smoke detection system.
The aspiration reducing film sheets are secured with marking tape to prevent it from becoming displaced.
Aspiration Sealant/Adhesive for Detection Pipe used to join the pipes / sleeves / bends together in an aspiration system.
ISP-104 from Xtralis are aspirator fans for IFT-P, IFT-4 and IFT-6 detectors.
Automatic Detector Isolation and assembly block for safety Ex barrier for insulated (earth-free) mounting of Part No. 764744 Ex barrier onto standard hat rail.
Avoor Din Rail Mounting is suitable for Esserbus alarm unit type 808623, voltage converters type 781337/781336 and fuse module type 382040.
Axial Lead/Cartridge Fuses are designed to meet an extensive array of performance characteristics in a space-saving subminiature package.
The B200S Series Intelligent Sounder Bases are designed for new and existing dwelling unit applications. They offers maximum flexibility in installation, configuration, and operation and provides two output volume levels such as 75 or 87 dBA.
B210W is detector base used for wireless detectors. It includes a built-in magnet so that wireless devices can establish installed and tampered states.
BAAS SaFlash Satellite Sound Alarm Autonomous Unit ensures broadcasting of the sound signal and the broadcast of a red light signal for the hearing impaired.
Indoor Bracket is designed for metal cameras.
Back Light Mirror with nine prisms
Valve for cleaning the tubing system through air purging via compressed air. In systems with air purging, the non-return valve is mounted at the end of the tubing branch and prevents a build-up of dirt particles at the end of the tube.
Baffles are used to direct the sampled airflow through the point detectors housed in the ICAM IAS aspirating smoke detector. Baffle are used for Gent S-Quad S4-710OH, S4-911 02HCO, S4-901 02HCO and comes in 10 Pack.
The optional base gasket is designed to fit to the S-Quad base to prevent water damage from dripping water from the ceiling.
Detector base is equipped with relay output and is specially designed for Series 9000 detectors.
Base with Side Cable Entry is an accessory for optical alarm signaling devices.
Flush-mounted basic housing covers are used for BUS-1 2-detector group connection modules.
Battery Extension Box is designed for Flexes Control and is necessary for any additional autonomy.
Battery Holder Kit is a Marine System Component designed for Marine battery box.
Battery operated alarm equipment have been designed to equip establishments requiring type 4 alarm equipment.
Beam angle bracket accessories are used for SenTRI beam sensors.
Parallel Bracket is the accessory for mounting the pair of beam sensors.
Gent by Honeywell’s S-Quad Beam Sensors provides an enhanced solution for linear beam detection for applications where point detection is either not practical or economic.
S-Quad Beam Sensors provides an enhanced solution for linear beam detection for applications where point detection is either not practical or economic.
The Beam Sensor accessories are designed exclusively for S4 Beam sensor.
Beam Sensor Transmitter mounted on a base fixed to either bracket allows the detection of smoke over distances from 2 m to 100 m each mounted on a base fixed to either bracket.
Blank Plates by Xtralis are provide solutions the earliest possible warning of an impending fire hazard.
The Blanking Baffle is used with ICAM IAS aspirating smoke detector.
The blind plates provide additional functionality for the VESDA VFT-15 detector.
Box cameras are an integral part of the 4 View range introduced for CCTV.
Adjustable bracket that allows you to install the also linear detectors of the ILIA series when the best do not exist fixing conditions inside the structure to protect.
The Mountera® Ceiling bracket are designed for installation of camera systems on ceilings.
Honeywell brackets and housings are aluminium cases particularly suitable for use in installations with ambient temperatures up to 70 ° C. These come complete with wall bracket, heater with thermostat and canopy. Heating is also available.
NCA/640-2-KIT is a Bracket installation kit required to mount NCA-2 to the CPU2-640/-640E’s standard chassis.The NCA-2 can be used as a primary display for the NFS2-640 by using NCA/640-2-KIT for directly connecting their network ports
The supporting bracket allows suspended or upright mounting of the alarm devices.
Break Seals are designed as replacement for Protective Covers.
Remote Control Equipment is designed with position control.
C-Rail Profile Mounting Kits are designed to be mounted inside the housing of the FACP FelxEs control. It is also used to mount a FOC converter in addition to single module housing.
The loop cards manage the wired links between a conventional Fire Detection System and the CMSI 8000 or manage the lines of Manual Triggers and the CMSI 8000 type B.
CMSI SensES R8 Rack is equipped with a CPU card and an HMI card. The rack provides compartmentalization, smoke extraction and evacuation functions.
CO2 Probes are required for S2401CO2 Detector.
The Vesda Xtralis CPVC is a Pipe Cutter with Upto 1.5”. Vesda piping systems are produced from specialty thermoplastics that offer unique benefits
Cable glands are designed for ulti-spectrum UV/Dual IR/VIS fire and flame detectors.
Cable Glands are accessories designed for manual call points.
Cable Sockets are accessories designed for Smart Temp electronic thermostats.
Cable Tray Clip is designed to attach to the cable tray side rails and secure the Protect wire in the recommended sine wave pattern.
Cavity wall mounting kit for touchscreen operating unit
Accessories for easier installation of the LRMX linear smoke detector and reflectors on walls, girders, ceilings and beams.
Ceiling Passive Infrared Detector have 360° coverage, range 16 meters in diameter installed at 3.6 meters in height.
Certification set is introduced for FlexES rack assembly.
The housing is used where it is desirable to monitor the air in ventilation ducts. It contains clear plastic housing, probes for supply and exhaust air in ventilation duct.
Consumable used in chemcassette based single and multipoint gas detection systems
Cover plates are introduced exclusively for call switch with pull cord.
Kit allowing the individual addressing of a manual call point on CMSI SensES type B.
The base is designed for sounder devices.
The base is designed for conventional detectors.
Conventional Fire Detection Panel is equipped with a graphic backlight LCD display, 8 lines and 20 columns (128x64 dots).
Conversion Kits are introduced as accessories for ICAM Flexible Aspirating Smoke Detection.
Custom Films with personalized description sold in packs of 10 and in multiples of 10.
F36-09-11 air filters are intended for use with DH100/200 duct smoke detectors.
DT8300-FMK flush mounting kits are designed for use with DT8320 Series DUAL TEC® motion sensors.
Warranty Extention extends the standard warranty period for DTS evaluation unit.
The Single Loop Base Card is a spare part for DX1 control panel.
Decal IQ8 Stickers by Esser are Swedish sign and signs such as evacuation alarm, fire alarm, siren symbol, hidden detector stickers in Swedish language.
Deep base gaskets are used for conventional Enscape audible visual sounders.
Deep Base O Ring are suitable for wall and ceiling mount installations.
Deep Waterproof Base is designed for wall-mounted beacons.
The base is designed for smoke, heat and automatic fire detectors.
The ES Detect automatic detector is an intelligent nonaddressable detector specifically designed for operation on conventional detector groups
Detector base with relay contact output, for detector family IQ8Quad FM.
Honeywell's detector buzzer sqm extension boxes have been designed to be used in case of an open cable system in detector buzzers.
Lid is used for detector buzzer SQM in polar white colour with logo on it.
Detector Cover Assembly with EMC Shields are spare parts of Very Early Smoke Detection Apparatus (VESDA).
Covers are designed for protecting the detectors against contamination during construction or renovation work.
Detector Dismounting Tool belonging to series 9000/9100/9200 can be opened and dismounted for cleaning by authorized installation staff.
When commissioning or maintaining a Sagittarius wireless fire alarm system, it is extremely important to check the proper communication between the elements.
Detector Lens is designed exclusively for Recessed Mount PIR Motion Detector.
The XR1000 detector pullers allows for quick installation and removal of ECO1000 series detectors at height without using stairs.
Accessories are designed exclusively for detector removal tools used for Series 9x00/ IQ8Quad Detectors.
Detector shelf plus display accessories are used for ICAM IFT-1 aspirating smoke detectors.
Detector Wire Base is designed for use with series smoke detectors.
Detector and AV standard base are low profile standard intelligent detector and AV devices which are Ivory based. Screw connections for cablings up to 2,5 mm, tamper option and address identification label.
Detector base with relay output for ES Detect 48 V DC operation
Detector removal tool
Device holder for mounting aspirating smoke detection systems to frames or for self-supporting mounting.
Disassembly Key is introduced under the Aspiration Accessories.
External dust filters for Midas gas detector are used to protect the tubing from contamination.This End of line particulate filter are used for normal gases .
Downloader Head for XP95, S60, S65 and Discovery Detectors.
Dual Height Clips are an integral part of the mounting accessories.
Dual Height L-Clips are designed for linear heat detection system. These are equipped with Silicone pads.
Dual Zone Water Trap Kit is used with XAS-2-US. It includes ¾ inch CPVC pipe, fittings and ball valve to provide water trap function on installations which are subject to high humidity and/or condensation.
Duct Sampling Kit includes 3 tube mounting plates, compression fittings, adaptors, elbows and reducers for use with XAS2-US, inlet and exhaust tubes and flexible tubing.
Duct Sensor is an accessory designed for the Vigilon System Sensors.
The Dulcet Series Cables are generally used for installations in Intelligent Conference Systems such as establishing connections between various units.
E Series ribbon cable accessories are used for ICAM aspirating smoke detectors.
E Series thermistor cable assemblies are used for ICAM aspirating smoke detectors.
E-CAB2 Container is a Universal metal container for peripheral cards. Ex: it can contain 1 MAB + 1 SCP-50-12 + IND16 + MORS 0 + MORS 1+ IND8. Dimensions: 380 x 265 x 160 mm
E1000 Series basic bases are intended for connection of fire detectors of the E1000 series to the receiving control devices of fire & security and fire systems in a 2-wire circuit, including a control panel with alternating voltage in the loop.
E³Point Accessories offers ECLAB Splash Guard Enclosures.
VESDA Capillary Sampling Connector systems are lightweight, and assembled easily in the field using inexpensive tools.
The ECO 1000 deep detector bases are used in the ECO1000 series conventional detectors with conventional fire alarm control panels.
ECO 1000/ Apollo protection is used to protect against moisture where the detector is mounted and places where condensation can occur.
The Xtralis VSM4 provide full and comprehensive integration of your VESDA and ICAM smoke and gas detection systems. The VESDA ECO Detector network connection One required per monitored detector.
ECO1000 Series basic bases are intended for connection of ECO1000 series fire detectors to fire and security and fire alarm systems (SCP) control panels using a 2-wire circuit, including a control panel with alternating voltage in the loop.
EMC shield for IQ8Quad, ES Detect detector base
ES Line Switchgear allows the management of the most efficient fire safety technologies. This technology makes it possible to target the few detectors to be changed during visits to maintenance.
ES Line Switchgear can manage up to 4 safety functions with position control and has an integrated power supply that can supply up to 2 A to be distributed over various outputs.
ES Smoke Detector Reflector available in size 10 × 10cm
The expansion kit is designed to increase the management capacity of the CMSI 8000.
The Edge Clips are used in cable based linear heat detection (LHD) systems.
The Egg Crate Grille is designed so that provision is made for a free area of 94% in order to preserve high level aesthetics whilst also maintaining the integrity of the vent from interference.
Electrochemical detector is Carbon monoxide detector with electrochemical cell for the protection of garages
The Enclosure box with DIN rail is designed for DIN rail mounted units. The box is well suited where there is a need for mounting DIN rail equipment on the detector loops.
ASD END CAP
Ex-barrier is designed for conventional operation of intrinsically safe detectors.
Ex barrier for intrinsically safe detectors Series IQ8Quad Ex (i) and 9100
Eltek’s Exi-/MaxLED wire suspension kits are used in ExiLED loop powered emergency light system.
Extender poles are designed for use with XR2B detector removal tools, and can extend 5 to 15 ft.
Extension mounting loop is designed for the use of EOL-O-final element in the flush box.
Extension Pole for XR2B.
Extension Rack is necessary to provide an extension for two 3U extension racks.
Extension pole
The Xtralis In-Line Filter provides Xtralis customers the ability to address a wide array of harsh environments with high levels of airborne contaminants in a simple and cost-effective manner.
External filter for FAAST with cartridge.
Extinguishing Module Signs are introduced as accessories for extinguishing equipment.
PanelSafe is a stand-alone fire detection and extinguishing system and is design to be an extremely cost effective fire detection solution for EDP server, telecommunication devices and switch cabinets.
F5000-LRK are long range kit for linear detector consisting of 3 reflectors to form a set of four that is included with the F5000M or F5000S detector.
CPVC socket unions are used in combination with other System Sensor® CPVC pipe fittings and related accessories to complete pipe networks in Fire Alarm Aspiration Sensing Technology® (FAAST) systems.
External Filter by Esser is used in all FAAST Systems
FAALT accessory boxes are used in FAAST LT 200 aspirating smoke detectors modules.
FAAST LT module mounting kits are the optional accessory for the FAAST LT range of aspirating detectors that allows an input or output module to be installed inside the FAAST LT unit.
FAAST LT-200 Models are the advanced fire detection system for use where early warning and very early warning are a required. This models allows early and reliable smoke detection.
Single or Dual Channel Accessories box for FAAST LT-200 Standalone
FAAST replacement air filters for aspirating smoke detector LT.
Notifier’s TV-4129742 are wall mount bracket for FC series thermal imaging camera.
The Filter Element for FLU2 Filter Unit is an accessory for ICAM series.
Extender Plate for E3 Series cabinet it’s an optional accessory.
FSL100 Flame Detectors
White Filter Elements are replacement for the internal filters inside the ICAM IFT, ICAM IAS and ICAM ILS series detectors.
FT series Replacement Filter Element consists of 10 pack with fine 45 ppi. It is in white color.This is available in medium and fine filter elements for the internal filters inside the ICAM IFT, ICAM IAS and ICAM ILS series detectors.
Fibre Cables are available in 30.0m Length with E2000 8° APC Pigtailmm.
Filter for LRS aspirating system
Keychain for fire and safety equipment's.
The XP3 fire detector poles with XR1000, XRL and IKR removers allows fire detectors to be installed and removed at high altitudes without the need for ladders.
The XRL fire detector removers with XR1000, IKR removers allows fire detectors to be installed and removed at high altitudes without the need for ladders.
Fire service key box FSKB type 2003 PZ
Notifier Fireray Flush Mount Plate comes pre-drilled to mount the FIRERAY 3000 detector head to any flat cable.
FTN SUP is a Bracket for pole fixing of the FST series barriers. For each pair of barriers 4 brackets are required ie. 2 for Tx and 2 for Rx. It has a diameter of 50mm.
Flame detectors stainless steel weather cover accessories are designed to protect the detectors from rain, snow and direct extreme temperatures from the sun.
Mounting Base is designed exclusively for Intelligent Low-Profile Plug-In Detectors.
Flush-mounted box for PAN1-PLUS.
Flush-Mounted Basic Housing Cover without LED opening allows connecting modules to be flush mounted. They are available in traffic-white colour.
FocalPoint Mobile Tablet for PC is used for non-control network annunciation standard hard drive.
The accessories are field installed and are designed exclusively for Honeywell’s Fusion Series.
The Eltek’s gas bottles are used with the Eltek heat detector testers which are test devices for testing of all types of heat detectors.
Gas detector mounting bracket accessories are used for stainless steel ATEX certified gas detectors.
Notifier Swing Gate Fitting Kits provide a quick and easy method for the continuation of an electronic detection zone, from the fence onto a swing gate.
Halogen Free Twisted pair cable without sheath or shield. It is flame retardant, halogen free, low smoke emission and low corrosivity.
Filter Unit 25mm with Filter Element for harsh environment.
Filter Unit 3/4in with Filter Element for harsh environment.
The VEU series of aspirating smoke detectors are the premium detector of the VESDA-E range. An Ultra-wide sensitivity range; 15 times greater than VESDA VLP, and provision for more sampling holes provide an increased coverage in high airflow
Heating Resistor is an optional element which connects the detector socket to the external power source with 2 WAGO cubes.
The 17007 hex key is a 9/64 key that is intended to unlock hex-locking pull stations.
High Profile Enclosure is designed with DIN Rail.
Honeywell Universal V‐Box controlled Shock Sensor, Switch selectable patented Double Knock and Remote LED reset options. It has dual sensitivity control, auto reset of relay contacts.
The Horizon detector bases are designed for use with Horizon range of conventional multi-criteria photoelectric smoke and heat detector. They have a built-in schottky diode which is used for head removal monitoring.
Housing is designed for accessories and is a part of the aspirating products range.
Housing for Ex barrier
The housing is designed exclusively for Linear Smoke Detector.
Housing surface mount, gray
The housing is designed innovatively with an IR body and aluminium roof, a wall bracket with internal cable passage and 230V thermostat control.
ISP-406 is used as a cover removal tool for IAS or ILS
SMB10 universal swivel-mount brackets are designed for use with SC100 and SC105 seismic vibration sensors.
Xstralis ISP-112-01 are the Detector Chamber used with ICAM Flexible Aspirating Smoke Detector.
Xstralis ISP-121 are the detector shelf plus display used with ICAM Flexible Aspirating Smoke Detector.
Xstralis ISP-115 are the E Series Cable assembly beacon used with ICAM Flexible Aspirating Smoke Detector.
Xstralis ISP-105 are the Exhaust Silencer used with ICAM Flexible Aspirating Smoke Detector.
Xstralis ISP-118 are the fan cable assembly used with ICAM Flexible Aspirating Smoke Detector.
Xstralis ISP-100-01 are the Gaswitch unit used with ICAM Flexible Aspirating Smoke Detector.
Xstralis ISP-123 are the replacement display for IFT-1 ICAM Flexible Aspirating Smoke Detector.
Xtralis ICAM Accessories offers Medium and fine filter elements for the internal filters inside the ICAM IFT, ICAM IAS and ICAM ILS series detectors. Replacement filters elements are available in pack of 10 with Black colour
The IAS/ILS Aspirator is an accessory for ICAM Series.
Xstralis ISP-107 are the TCP/IP Rabbit Processor Module used with ICAM Flexible Aspirating Smoke Detector.
IFT-6 Replacement display accessories are used for ICAM IFT-6 aspirating smoke detectors.
IFT-P Chassis accessories are used for ICAM IFT-P aspirating smoke detectors.
ISP-114-01 from Xtralis are detector chambers for ICAM IFT-P detector.
IFT-P Fan cable assemblies are used for ICAM IFT-P aspirating smoke detectors.
ILS-1 Display kit accessories are used for ICAM ILS-1 single channel laser aspirating smoke detectors.
ILS-2 Display kit accessories are used for ICAM ILS-2 dual channel laser aspirating smoke detectors.
IP 43 moisture-proof sm base
IP 55 Outdoor Barrier is a mini active infrared barrier with 4 lenses with small dimensions.
The base is designed with a heating resistor and is a part of the Addressable Centrals introduced by Esser.
IQ8 Control Panel is an integral part of the Intelligent Addressable IQ8Control range introduced by Esser.
IQ8Wireless technology enables the IQ8Quad automatic fire detectors (with and without alarm signaling units), MCPs and the IQ8Alarm signaling unit to be wirelessly connected to the fire alarm system IQ8Control and FlexES control.
IQ8Alarm Plus IP base
The IQ8Alarm Plus device is painted and delivered according to the required RAL colour. For identical colours, it is suggested to order a suitable number of additional pieces.
Visual Alarm Diffuser designed for IQ8L range meets the requirements of the labor code and the safety regulations against fire risks in public buildings in terms of welcoming deaf and hard of hearing people.
IQ8MCP Addressable Manual Call Point is equipped with status indicator, membrane, short circuit isolator, transparent protective cover and mounting base.
IQ8Quad IP42 Protections provides protection to the IQ8Quad detector base against dust and humidity.
IQ8Wireless mounting frame for IQ8Quad detectors, white
IQ8Wireless mounting frames for IQ8Alarm / IQ8Alarm Plus, red and white
ICAM FLOW SENS ASSY IAS/ILS
In-Line Filter Elements provide to customers the ability to address a wide array of harsh environments with high levels of airborne contaminants in a simple and cost-effective manner.
Indoor / Outdoor Housing is designed for FD series dome.
Indoor / outdoor bell housing is designed for VD series domes.
Indoor/outdoor Bell Housing for VD series Dome Dimensions.
Inertech Pressure Vents are high performance vents which provide 100% efficiency at the pressure of 95.5 Pascals.
The base is designed for Infrared Flame Detectors.
Inline flow restrictor assembly used for refrigerated storage sampling kit. The Xtralis refrigerated storage sampling kit provides a standardised method of smoke sampling for Refrigerated Storage facilities.
Inner Cup is innovatively designed for models used in detector testing.
Transmission units and transponders installation frames are specially designed for 8000 C/M, IQ8Control C/M and FlexES control panels (IQ8Control C and FlexES control only with extension housing).
Installation adapter for suspended ceilings
Installation and maintenance kit is equipped with alignment laser tool, test filter, pc cable, cleaning cloth and user manual.
Installation/removal tools are designed for use with System Sensor® plug-in smoke detectors. They permit installation and removal of detectors in elevated mounting locations.
Instruction Sign is a part of the Diverse series introduced by Honeywell.
The Intelligent Notification Module is an addressable notification module for use with Honeywell Silent Knight series fire alarm control panels (FACPs). It provides supervised monitoring of wiring to load devices
Intelligent Thermal Detectors by Honeywell are thermal detectors with integral communication has features that surpass conventional detectors. Point ID capability allows each detector’s address to be set with decade address switches
T55-127-010 removal tools are for use with Fire-Lite® intelligent detectors. The extender pole is not included with T55-127-010 tools.
A1100A are interface box for Modbus which provides access via the Modbus protocol over RS232 and RS485 as well as TCP/IP.
Internal Filters are designed exclusively for suction systems.
Internal replacement cartridge for external filter, compatible with aspiration systems.
The Zener Barrier prevents the transfer of unacceptably high energy from the safe area into the hazardous area.
Kit consisting of gasket and front panel for PAN1-EU and PAN1A-EU which allows the panels to reach IP 55 degree.
Key Depot Adapter SDA 3000 have been designed for connecting an FSD type basic to a fire alarm control panels.
L-Brackets are designed for linear heat detection system. These are equipped with Silicone pads.
23165 trim rings are for use with LCD-40 Series remote annunciators.
LED keypad combi system accessories includes LED bezel in white, grey, black and clear colour and replacement Key mat.
LED/LCD keypad combi system accessories include LED / LCD bezel in white, grey, black and clear colour and replacement Key mat.
Accessories for the LRMX linear smoke detector
LRS Aspirating Filters are used in extremely polluted environments.
Label Detectors are recommended that signs be mounted on the detector base. Label Detectors can either be marked with a sign or numbered on the underside with felt-tip pens.
VESDA Aspirating Pipe and Fittings are produced in redABS under a stringent quality control system.
Label plate for detector base IQ8Quad
Label-smoke detector pipes are manufacture from ABS (Acrylonitrile Butadiene Styrene), very lightweight, versatile material, guaranteeing you easy and professionalinstallation.
The labels-sampling points wrap round serves for the marking of the intake points of the PVC/ABS pipe.
Laser Pointer Unit highlights the cone of vision enabling the designer/installer to identify best position to mount the flame detector to give optimum coverage.
Blank Sub-Unit are an integral part of Sub-Rack Remote Display Assemblies.
Lettering is introduced for sign boards of the series 5500.
Light shield is available for installation in areas where direct sunlight cannot be avoided
Log book for FAS (DE/GB)
Low noise nozzles are designed to discharge the inert gases in a uniform configuration and reduce air turbulence and noise in the enclosure.
Low profile base is designed for addressable audible warning devices.
Surcharge is the additional cost for ordering low quantity of detectors, detector base and remote indicators.
M200 Series surface mounting boxes are used for M200 series input or output modules.
The M200XE Series Input/output Modules have single, dual or Conventional zone type I/O modules. This modules are provided with built-in short circuit monitoring and isolators on the intelligent loop.
HNMSEB hard drive trays are for use with MAXPRO® NVR SE Series video surveillance systems.
Connecting Box
MBP is a bracket attachment for the transmitter-receivers units and are mechanically integral to those units.
Magnetic contacts surface-mounted base accessories are suitable as mounting aid for height compensation. Surface-mounted base accessories are used for flat reed contacts.
Includes moulding, hinges for user interface door, push clip fasteners, Notifier label and hex fixing tool.
The bezels are designed for flush installation.
Manual Call Point Modules are designed exclusively for CMSI 8000.
Message Sound Diffuser meets the requirements of the labor code and the safety regulations against fire risks in public buildings in terms of welcoming deaf and hard of hearing people.
Midas® Gas Detector
Morley-IAS Bezel Kits are semi flush mounting kit for ZX1(S)e or ZX2(S)e control panel.
The mounting adapter is used for quick and secure attachment of bases of the IQ8Quad detector series, 9x00, IQ8Alarm Plus and alarm signaling devices, parallel detector indicators, etc. to suspended ceiling systems.
Mounting box detector accessories are used for VESDA series detectors.
Mounting Brackets are available in pack of 10.
Mounting bracket line detector for FireRay 5000.
Mounting Bracket for Heat Detector ATEX type TMP2.
Mounting kits are designed to be used on round and insulated air ducts.
Mounting Kit for 24 Analogue Channels.
Mounting bracket for lintel installation
Mounting frame for small MCP, red and white
Mounting kit
Mounting rail for FACP
Multilingual interface card packs for FAAST XM aspiration detectors.
Multiple mounting support brackets allows the F5000M or F5000S detector to be installed on sloping ceilings or walls with an angle greater than 10º.
NEODT are Dual digital technology PIR and MW X-Band Detectors with EOL resistors.
The Sound Diffuser is an integral part of the fire alarm sound devices designed for IQ8S range.
NFR-BS is a standard base for automatic detectors with terminals for connecting VUOS. When the detector is removed from the base, the loop integrity is not violated.
NS-GX-ETH Ethernet Interface allows the connection of GALAXY DIMENSION control units to the Enet cpu, via the ETHERNET network.
Non-return valve is designed for use with the FAAST aspiration smoke detection system.
OPAL AV Mounting Base is a mounting base which is deep waterproof and is ivory in colour
OPAL™ Deep Profile Base available in Ivory colour.
Bracket for mounting on oblique surfaces of barrier emitters and receivers F3000. They offer 360 degrees of rotation plus 180 degrees of adjustment.
Optical Smoke Detectors are equipped with detector insert and base.
Optical Smoke Switch are innovatively designed are replacement products.
Optical Smoke and Heat Detectors suitable for smouldering and open fires.
IP 55 outdoor barrier. GEMINI is a mini active infrared barrier, with 2 lenses, with small dimensions. Pre-wired and ready for installation, it consists of a transmitter and a receiver unit with 8 selectable digital frequencies.
SEN-INT-ACDIN Interface is a 240V output interface and it comes with a DIN Rail mounting kit.
PAN1-PLUS-SC Bracket is a Metal bracket for ceiling and flag mounting for PAN1-PLUS.
PC Software Tool Kit is dedicated to commissioning the CMSI 8000 addressable fire protection centralizer.
Flush Sample Point Head only for 10 mm OD tube.
Pipe Accessories are specifically used with ¾” diameter pipes.
Pipe cutter under pipes and Fittings products have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system.
Pipe Ties comes under accessories of pipes and fittings.
Plastic box for multimodal to accommodate up to six standard modules of the M7xx series. Constructed in antistatic ABS, ignition characteristics V0 light cream leaks and transparent cover to display the status LEDs and the address of the modules.
Plastic Clamp Sets are accessories introduced for Fibre Cable Mounting.
Plastic Replacement Kit for SOLO2001-001.
Plate Pole Adapter 241x161mm for poles with a diameter of 15 to 19 cm.
The point detector wired bases are used with smoke and heat fire detectors of the System Sensor PROFI, 100, 400 series when connected to control panels with alternating voltage in the loop.
Replacement filter element is designed for Microfilter for use in areas with extreme pollution.
Kit for CMSI SensES for connecting the waiting or safety positions of the DAS.
The power module makes it possible to increase the electric power available at the output of the lines for UGA exhaust diffusers.
Premounting for freestanding key box
Pressure Gauge is designed exclusively for 850 & 855 EEBA.
The Pressure Surge Reducer is an accessory designed for pressure switches.
Prism Plate is designed for Universal bracket.
The front foil is designed for Pro Sens smoke extraction system.
The protection box equipped four cables outside is designed exclusively for surge protectors.
Protective grilles for detectors are designed for protection of point detectors against mechanical damage.
Protective cage
Q9033A Aluminum Mounting Arm Assemblies are used for aluminum X5200, X5200G, and X5200M flame detectors.
QUIPBRK are the joint used for sensors that allows you to adjust the horizontal orientation of the quip line detector.
The coupler is designed with 12 relay output for panel or rack mounting and is supplied with short-circuit isolator.
The converter enables galvanic isolation of the interfaces between the fire alarm control panel and an external device.
The enclosures have a glazed lockable door and an internal swing frame to allow easy access to the back of the sub rack.
Rain protection cover for FSKB 2003
Magnetic recessed contact for armored doors with 4 output wires (length 30 cm) for contact and anti-tampering, suitable for installation on iron and non-ferrous doors and windows. Container is made of brass.
Recess Mounting Kit for remote single boxes.
Recessed Mounting Kit is designed for mounting Smoke Detectors.
Red Flashing Light is completed with bracket and wall support.
Remote Annunciator and Control Unit is used with the 6500 range of projected beam smoke detectors. It is ideal for installations where access to the detector is restricted.
Kit for CMSI SensES for connecting the DAS remote control lines.
Remote laser test tools are used in in conjunction with the Vision range of detectors for triggering the Vision detector. These test tools have hand held unit which provides an effortless-way of remotely triggering the Vision detector.
Replacement beacon cover accessories are used for ICAM aspirating smoke detectors.
The Replacement Filter Elements are Medium and fine filter elements for the internal filters inside the ICAM IFT, ICAM IAS and ICAM ILS series detectors.
Replacement Filter Element Kit available as an accessories with A300 series Aspirating Smoke Detector
Replacement Key for ASD/LASD Aspirating detectors or A300 series housing.
MIDAS-A-007 Internal Pump Module is designed to operate for a minimum of 24 months and it is recommended that this pump module be replaced every 2 years.
Replacement air filter pads for 801544
Reset Module is equipped with mounting brackets.
Reset Module is an interface allowing the automatic reset of special detectors connected to intermediate units OI 3000 or OI 3001.
Resettable Elements are accessories designed for XENS-800 and XENS-805 manual call points.
Retardant Microbore Tubing is 1/4" UL Listed for use with VFT-15 detector. It is available in 500 & 1000 ft.
S-Quad accessories is designed exclusively for S-Quad Multi-Sensor and Visual Alarms Device.
S-Quad Mounting Plate is an installation base used for installing S-Quad Multi-Sensor.
Gent S-Quad Sensor Bases are used for all S-Quad Sensors. Available in White or Black.
The System Sensor B524HTR is a specialist base in addition to the traditional low profile or deep bases, designed for use with all System Sensor 200 analogue addressable detectors
Sockel mit integriertem Isolator für den Notifier - Ringbus für Melder der Serie 700
B401 plug-in detector bases are used with System Sensor® conventional S300 smoke and heat detectors. These bases make detectors more versatile than equivalent direct-wired models.
SALTO Wireless RF Node is part of SALTO’s RF2 system. It works as a bridge between Gatewayx2, SALTO ProAccess or HAMS for Service access control software and RF locks.
Sound Diffuser meets the requirements of the labor code and the safety regulations against fire risks in public buildings in terms of welcoming deaf and hard of hearing people.
SOHI Container for ILIA series detectors ERHS and ERRHS, with pressure cap, to be used in environments where there are problems of vapours, acids or particular powders or need to carry out cleaning-washing-disinfection with high pressure jets.
SR surface mounting box trays are used for conventional indoor and outdoor call points.
STI Mini Stopper® equipped with a frame has been helping stop false fire alarms around the world for decades without restricting legitimate operation of pull station.
The STI is an accessories that are been used with STI Stopper II®. The accessories that are been used are conduit gasket and conduit spacer.
The Safety Bus Enclosure has Cable trays, Field terminals and Earth bar. It is used for Up to 5 SB modules.
The Salwico EC detector adapters are the connection adapter with an integrated 470Ohm serial resistor for installation of EC-type detectors on the IP55 base NS-2IP55 or 2IP55. This adapters are made for use in wet spaces.
The Salwico EC detector bases are low profile base plate for smoke and heat detectors from Salwico EC range of detectors. They are equipped with an integrated 470 ohm serial resistor for installation of EC-type detectors.
Sampling Point Label supplied as an accessories with A300 series Aspirating Smoke Detector available in roll of 100.
The labels are designed for the marking of the intake points of the PVC/ABS pipe.