520-FIN Sampling Points are used for Capillary Tube.

530-FLEX Flexible tube with elastomer and interior metal spring is an accessory used for Suction System.

530-TAP Sample Tubing End Caps is 5 Pack accessory.

530-TUB Sampling Pipe is a 3 meter long tubing of ABS material (Acrylonitrile-Butadiene-Styrene) which is halogen-free.

The Venturi tube enters the duct and leads the air out of the duct through the detection chamber of the detector back to the duct and finally back into the duct.

FS-1200 FLAME SIMULATOR allows remote testing of flame detectors, which are often located in difficult to access and/or classified hazardous areas

90 Angle Pipes are accessories designed for Aspiration Smoke System

90 Bends for Sample Tubing Pipes are also available in V0 FIREPROOF material and in WHITE ABS material. To place your order, add / V0 or / B respectively to the pipe reference. Supply on request, check prices and delivery times.

Smoke Detector Tester allows fast and reliable functionality testing for Series IQ8Quad and 9x00 smoke detectors. Through reduced mechanically controlled actuation pressure, suspended installed detectors can also be tested

ABS (Acrylonitrile Butadiene Styrene pipe is a homogenous material with good chemical resistance and high impact strength. Other beneficial features are its suitability for use at low temperatures.

The VESDA Xtralis provides the discreet detection required in heritage buildings by routing the sampling pipes in areas that are not visible from normal occupancy. Small-bore capillary pipes are used to provide detection at the required location.

ABS pipe is designed specifically for the aspirating smoke detection industry.

Adapter for Esser Poles are designed for attaching the 805580 detector removal tool and the 805582 smoke detector tester.

RMS-GR break glass rods are intended for use with N-MPS and NFW-MPS Addressable Series manual stations.

Morley IAS Aerosol Testers are Ecological and non-flammable gas aerosol in metal container to check smoke detectors.

Air Duct Detectors are for usage of the OTblue-LKM Part No. 802379 air duct smoke detector in combination with Venturi tubes Part No. 781446, 781447 or 781448 & The semodule is mounted on the outside of the air ducts

Immersion well with fixing flange for air ducts.

Air Sampling Test Point comes under accessories of pipes and fittings. It includes cap.

Aspirating Smoke Detection Accessories are 45° Elbow, Condensate Trap, End Cap, Mounting Clip, Socket to Socket Sleeve, Socket to Socket Sleeve Adaptor, Socket Union and T-Piece.

Eltek’s aspiration condenser separators for detection pipe do effective drainage of condensation water, mandatory on all aspiration systems where there is a lot of condensation/moisture. It is mounted on piping immediately before aspiration detector.

Aspiration filter for use in exposed environments, where you want better filtration.

The Aspiration fitting accessories consists of tubes, bends, brackets and expansion units.

Mounting Clips are accessories designed for Aspiration Smoke System.

Nylon capillary tube rolls of 100 meters with 10mm outer diameter and 8mm inner diameter are used for aspiration systems.

Aspiration test smoke datax modules are safe for electronic equipment’s.

Ball Valves are For manual disconnection of aspirating smoke detectors from connected piping system during the blow cleaning process with compressed air.

Black polyethylene tubings by Xtralis has an inner dia of ½ inch and outer dia of 3/8 inch.

The CO Capsules by Testifire are non-hazardous, non-pressurised, environmentally-friendly capsules to generate smoke and CO.

CO Capsule Multi-Stimulus Detector Testers are for the testing of detectors with carbon monoxide sensors (CO) & Especially suited for the IQ8Quad OTG Multisensor Detector 802473 (with CO sensor).

Carbon Monoxide Detector are used for after sales service for LCR 3 .

CO Test Gas by Esser Specifically designed for the OTG multisensor fire detector (CO) IQ8Quad with isolator (Part No. 802473), suitable for smoke detector tester.

Calibration Instrument is a portable instrument for calibration of detectors type AS / ASF / BS / BSF. Case included.

Capillary Conical Sample Point Kit for 25mm Pipes.

Capillary Discrete Sampling Point Kit for 25mm Pipes. Capillary tube is of 2 meter. Material used is T-Piece and Flush Head in ABS OD Tubing in Nylon.

Capillary Flush Sample Point Kit for 25mm Pipes. Capillary tube is of 2 meter. Material used is T-Piece and Flush Head in ABS OD Tubing in Nylon.

Capillary Sampling Points has composed of flexible nylon tube 1 meter long, 10mm outer diameter and 8mm inner diameter and support for false ceiling.

Capillary tube bushing Rubber plug for 3 mm capillary tube.

Capillary tube bushing Rubber plug for 3 mm capillary tube. Bore diameter 10 mm.

The carrying bag has many pockets and compartments in which the ESSER smoke alarm testers, test gas bottles, all cables and other maintenance accessories can be stored. So everything you need for maintenance can always be found in one place.

Condensate trap with sintered metal filter for separation and absorption of condensed liquids, used for protecting aspirating smoke detectors against humidity condesate, oil, etc.

Condensation Trap for aspirating pipe smoke detection systems.

Conical Rosette for Capillary

The Sampling Point from the VESDA (By Xtralis) Range of Pipe and Fittings products have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system.

Connector Elbows by Eaton are pico fitting with tubes.

This is a 100V to line converter

Low Pressure cylinder regulator fitted with the latest Consumer Safety Protection system required by the UK standards to cover all fixed pipework installations.

D4PCVR covers are replacement covers for D4120 duct smoke detectors.

DCOIL remote test coils are required for older DNR(W) duct detector housings.

Detector Tester Kit Testifier 2001 for the functional testing of point-type fire detectors with various sensors.

Diagnostics tool for Titanus EB aspirating smoke detector systems are used for reading the measurement data and device configurations as well as for localization of faults.

Discrete Capillary Sampling Point for 10mm QD tube.

Discrete End Caps are range of sampling points to customize unique needs of applications.

Notifier's P-EE/EU is a polycarbonate film with the word "EMERGENCY EXIT" for PAN1-EU, PAN1A-EU, PAN-1E / AE.

POL-ESS TOUCH is a professional configuration tool which is able to recognize all esserbus or esserbus-PLus and ES Detect loop devices, whether configured or new. Being standalone means you can work from anywhere in the system.

EXT steel exhaust tubes are intended for use with HVAC duct smoke detection and monitoring products.

End Caps are accessories designed for Aspiration Smoke System.

French Entree Interdite, Available messages for the Series 5000. Messages are also available individually

Range of Pipe and Fittings products have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system.

Spare Exhaust Adaptor for the VEU series of aspirating smoke detectors.

External Sensors by Honeywell are electronic thermostats, with LCD display for the field of plant construction, fluidics, process technology, and pneumatics.

External Water Trap Kit is of 25mm. External Water Trap Kit is used for protection of aspirating smoke detectors.

FAAST Automatic Purging Unit provides a fully integrated and compact solution with user-selectable preventative or event triggered purging programs.

FAAST Series

It includes 1 x red ABS tee, 1 x red plastic pipe inlet nipple, 1 x 1/8in red straight quick coupling, 2m of PA12 flexible 10mm x 8mm polyamide hose. 1 x 1/4in red cylindrical nut and, 1 x white PVC plate with 1/8in connection for pipe.

FDS Connection Boards by Honeywell are ATS adapter for fire panels that provides an interface for fire alarm systems according to DIN 14675, appendix B and VdS 2463.

FS-1300 FLAME SIMULATOR allows remote testing of flame detectors, which are often located in difficult to access and/or classified hazardous areas

Flush Sample Point Kit includes c/w 2 m of 10 mm OD tube, trunk adaptor, point and decal. It is vailable in white colour.

Honeywell XNX Universal Gas Detector Transmitter for monitoring Carbon Monoxide (CO) 0-300ppm (100 to 999ppm, 100ppm) compatible with all Honeywell gas sensing technologies with aluminum housing.

Gent Venturi Tube is used with Duct Smoke Sensors.

Polycarbonate Films by Notifier are green polycarbonate film with white writing background "CO2 Deactivation System Disabled".

Exhaust Deflector is used with VESDA VLF. It is available in grey color.

Honeywell Duct Smoke Sensor is an optical smoke sensor specifically designed for use in ventilation ducting. A venturi probe samples the air in the duct for smoke. Detector housing is mounted externally to the duct.

Xtralis Accessories offers IAS/ILS Corner Studs. Corner Studs are used as spare part and available in pack of 4.

ICAM Microbore Accessory is typically used where there is risk of small insects or dirt entering the microbores.

ICAM Pipe Kits by Xstralis are provides full and comprehensive integration of your smoke and gas detection systems.

ID50 Series Support Tool Kit includes offline configuration software, online manual, interconnection cable assembly.

Immersion tubes are used for thermostats and temperature transmitter

Feme Automation immersion tube is used in thermostats and temperature transmitters.

The Immersion Well is an optional accessory for strap-on thermostats. This well is of Nickel-Plated brass.

Immersion well temperature sensors are five inch long stainless steel sensors that are intended for use with models C7021D2001, C7023D2001, and C7041D2001.

Inline Expansion Socket comes under accessories of pipes and fittings. This is 25mm with socket of 100mm.

Detector interface is an accessory of Intelligent Fire Detector for visual display of sensor status on a PC.

Intelligent Loop Test Tool is a loop diagnostic device designed to help technicians save time when working with analogue loops.

Intumesent 2hr Fire Collar comes under accessories of pipes and fittings. This is 25mm.

Jointing Sockets by Xtralis are allow for the connection of 2 lengths of pipe and should always be connected with ABS solvent cement.

Replacement LED lamp for room electronic modules

LF422 flexible single core tubing provides 1/2-inch inner diameter flexible tubes for use with XAS units in duct sampling.

Large Check Valve comes under accessories of pipes and fittings. This is 25mm and also called as blow out valve.

DTS (Distributed Temperature Sensing) System is capable of detecting fires and accurately locate spots of the fire. It allows to precisely measure, locate and signalize already small differences of temperature changes

The POL-200-TS loop tester is a versatile measurement & analysis tool that assists technicians with the installation & maintenance of fire detection systems. The POL-200-TS recognizes all addressable loop elements.

M6 Nut comes under accessories of pipes and fittings. This is used for fitting clip to the end of threaded rod.

M6 Raw Plug Adaptor comes under accessories of pipes and fittings. This is used for fixing clip to wall.

M6 Rod Adaptor comes under accessories of pipes and fittings. This is used for fitting clip to side of rod.

M8 Nut comes under accessories of pipes and fittings. This is used for fitting clip to the end of threaded rod.

M8 Rod Adaptor comes under accessories of pipes and fittings. This is used for fitting clip to side of rod.

The MAU Threaded Joint is available with male adapter union. It is used for differential pressure switches and transmitters.

VESDA-E VEA microbore tubes are custom made, high quality plenum rated flame retardant polyethylene tubes. They have superior stress crack resistance for reliable long-term performance

Moisture Protector is a permanent anti-humidity protector with test input.

Mounting Clip is an accessory for 25mm pipe.

NPT adapter is to connect pressure switches, pressure transmitters, pressure gauges, etc. to NPT threaded connections and suitable sealing washer is also supplied.

Immersion well for thermostats and temperature transmitters

NTFAAST Series

Natural Capillary Pipe comes under accessories of pipes and fittings. This is 10mm OD.

Notifier's P-NE/EU is a polycarbonate film with the word "NO ENTRY" for PAN1-EU, PAN1A-EU, PAN-1E / AE.

Smoke Generators have cartridges for the generation of orange smoke.

The PAC is a system intended for the automatic and periodic cleaning of the sampling networks.

PAN series signalers have Polycarbonate film with the words "ALARM IN PROGRESS" for PAN1-EU, PAN1A-EU, PAN-1E and PAN-1AE models.

PAN series visual/acoustic appliances are available with the word “Fire Alarm” for PAN1-EU, PAN1A-EU, PAN-1E/AE series strobes.

The Pipe Elbows by Honeywell are used to divert pipework around obstructions. They should always be connected with ABS Solvent cement.

PRO E-Series vertical alignment tools are WLAN controlled alignment accessories for ADPRO® PRO outdoor perimeter sensors.

PVC Pipes are accessories designed for Aspiration Smoke System

PVC Sleeve is an accessory for 25mm pipe.

T-Piece is an accessory designed for Aspirating Smoke Detectors.

The PVC Test Adapter is available with Plug. It is used for testing the suction system.

The Gamewell-FCI XP95-P Analog Addressable Photoelectric Sensor is designed to operate with the Gamewell-FCI and Fire Alarm Control Panels (FACPs).GW71112 is an additional blank Xpert addressing cards

Pipes are accessories designed for Aspiration Smoke System.

In areas with a high amount of dust a special filter type SF-400 with a larger surface is available. The special filter guarantees a safe filtration of dust and dirt. SF400-E is the filter element for special filter.

Pipe Kits for VLQ-100 are a comprehensive range of products provided for VLQ Aspirating Smoke Detectors.

Pipe Tee are also available in V0 FIREPROOF material and in WHITE ABS material.

Plastic Telescope Rods are extendable detector pull-down pole made of glass-fiber reinforced plastic for adapting the detector removal tool as well as testers.

Esser's Telescopic Rod is an extendable detector pull-down pole made of glass-fiber reinforced plastic for adapting the detector removal tool as well as testers.

The pole adapter accessories are required for FC series thermal imaging cameras.

Polycarbonate Films by Notifier are polycarbonate film with "FORBIDDEN TO ENTER" for PAN1-EU and PAN1A-EU.

The PTL-611 Portable Test Lamp is a flashlight for ATEX and are high impact resistant.

Remote hand-held programming unit and test unit are used in conjunction with the Series 300 range of detectors to gain access to other advanced features.

Retrofit Adaptor Converting Legacy Light Spot Mounting is a range of high performance PIR sensors for dependable control of analogue and digital dimming lighting loads.

The Rilsan tube accessories are required for ASD-PICO-FIRE tracers.

Ring Nut for gas detectors, sensor head diameter 35mm.

The S4-34741-50 are S4 Obscuration Test Card designed for use with gent beam detectors.

SD505-DTS-K remote test switches are designed for use with model SD505-DUCTR duct smoke detectors.

SDT Series Smoke Detector Testers is 250ml SOLO aerosol for use with SOLO 330 smoke dispenser.

The SMART3 series calibration kits are required for gas detectors and they are available with watertight or explosion-proof head in metal cases.

SMART3 Series Collecting Cone is collecting cone and weather protection in stainless steel for type 3 gas detectors.

SOLO 101 Extension Pole for detectors has a 1.3m length for SOLO-100 rod.

SOLO Adapter Tool 713 for connection of ECO1000DRT detector removal tool.

Notifier SOLO Aerosol Smoke Dispenser fundamental to functional smoke checking for many professionals around the world the Solo 330 contains the test aerosol and ensures that it is applied correctly and contained only where required.

SOLO Cordless Heat Detector Tester Kit is the industry’s most popular standalone heat detector tester. The battery-powered Solo 461 is suitable for testing heat detectors up to 90C.

SOLO Detector Testing Aerosol 250ml is the only way to verify a CO detector is to introduce CO into the sensor of the detector.

SOLO Mains Heat Tester has a voltage rating of 220V-240V. Compatible to SOLO 814 model.

SOLO Non-Flammable Green Gas Aerosol is ecological gas aerosol to test the 150ml smoke detectors.

SOLO Series black colour Carrying Bag is semi-rigid material transport bag to house all the elements of the SOLO series. Used with SOLO 811, 812, 814, 822 and 823 detector testing kits.

SOLO Smoke Detector Test starter Kit of 6m includes one 4.5m SOLO fibreglass telescopic extension pole and one SOLO 330 aerosol smoke dispenser.

SOLO Telescopic Access Pole is extends from 1.26m to 4.5m in 4 sections allowing access to detectors fitted up to 6m.

SOLO Telescopic Fibreglass Pole is extends upto 1.13m in 4 sections allowing access to detectors fitted up to 6m.

SOLO Universal Detector Removal Tool is faced with a vast array of different models shapes and sizes the professional needs a universal tool.

SS Series UV/IR test lamps are designed for use with SS4-AS, SS4-AS2, and SS4-AUV2 fire and flame detection devices. They come with a PW-3123-0005 universal charger.

ST metal sampling tubes may be installed from the front or back of System Sensor® HVAC duct smoke detection and monitoring products. The tubes lock securely into place and can be removed by releasing the front or rear locking tab.

STGD Ring Nut for gas detectors, sensor head diameter 35mm. Adaptor for type 3 sensor heads.

STS air sampling tubes are intended for use with duct detection devices.

Flexible Connector by Xtralis is an integral part of the VESDA aspirating smoke detection (ASD) technology.

Sample Tubing Pipes are also available in V0 FIREPROOF material and in WHITE ABS material. To place your order, add / V0 or / B respectively to the pipe reference. Supply on request, check prices and delivery times.

Sampling Hole Clip delivers reliable and accurate sampling hole sizes that are fast to install and easy to locate and identify.

Sampling Pipes Fitting are also available in V0 FIREPROOF material and in WHITE ABS material. To place your order, add / V0 or / B respectively to the pipe reference. Supply on request, check prices and delivery times.

ICAM by Xtralis provides various sampling points for the different applications. The classic sampling points are typically used for cabinet protection.

Sampling Point Kits of 8 points are available in red and white color with pack of 5.

Connection connector In mounting box for creating access point for Scorpion test instrument.

Scorpion Control Unit is a portable test device that connects to the access point and can acid the test from a handheld device.

Scorpion Control Unit Panel is a unique, functional remote testing system for aspirating smoke detectors.

Scorpion Head Unit Kit is a test probe for connection to a Scorpion controller via cable.

Scorpion Point Smoke Detector Test Head is a smoke generator that can be installed next to a detector and allows, when necessary, to generate the smoke directed towards the detector itself to perform a functional test of the control device.

Scorpion test units are used to test the point detectors which are effectively controlled from the Scorpion access points and service instruments or Scorpion control panels.

SenTRI duct venturi tube accessories are used for Duct sensors.

SenTRI venturi tube accessories are used for Duct sensors.

Sensepoint XCD Calibration Kits are specially designed for monitoring gases along with Honeywell Analytics' sensors in potentially hazardeous or explosive atmosphere.

Sight Glass with Condensation Drain comes under accessories of pipes and fittings. This is 25mm.

Smokesabre (SABRE01) is a smoke aerosol for quick, low-cost, functional testing of smoke detectors with a simple wrist set.

Smoke Capsule Multi-Stimulus Detector Testers are for the testing of smoke detectors series IQ8Quad and 9x00 with optical and/or ionisation sensors.

Smoke cartridge for use with Solo 365 Smoke Detector Tester

Smoke Detector Testers are designed for electric function control for the IQ8Quad and Series9x00 detectors.

Smoke Generating Match has 10 smoke cartridge of 3g for 40 seconds with grey smoke.

The smoke generation capsule accessories are required for TESTFIRE 1001-101 or SOLO 1001-001 and 2001-001 series detector test kits.

Esser's PREM-009 Smoke Generators are used for generation of gray smokie in areas where electronic equipment are used.

Smoke Pen Kits are refillable wicks, the device works like a mechanical pencil; where a wick can be inserted into the pen, leaving a 10mm trace that can subsequently be ignited by either a lighter or match.

The Smoke Pen Refill Pack comes with 6 spare wicks for Smoke Pen. The burning time for each wink is 30 minutes. Therefore, a total burn time of 3 hours can be reached with one smoke pen refill pack.

Smoke and Heat Detector Test Kit with display.

A universal remover that fits the same extension rods used for detector testing.

Immersion well for thermostats and temperature transmitters

Stainless Steel Sampling Points are essential to VESDA Aspirating Smoke Detectors.

The Smoke-Pen has become one of the most versatile tools of usual tests, even if simple to use has various application possibilities.

Capillary Sampling Points has composed of flexible nylon tube 1 meter long, 10mm outer diameter and 8mm inner diameter and support for false ceiling.

TSE-A100 self-contained smoke generators are some of the most advanced units of their kind and are the result of extensive research and development. They are designed to make the job of testing detectors a simple and efficient operation.

Feme Automation immersion tube for thermostats and temperature transmitters.

The Tamper Proof Sampling Points (TPSP) provide an elegant addition to modern decor and can both minimize the risk of vandalism and tolerate abuse.

Telescopic extension are used for plastic telescopic rod. Up to 3 telescopic extensions can be attached to the telescopic rod and the maximum height that can be reached is increased to 9 m.It is used in various detectors as accessories.

Test Head for Heat Detectors have devices for testing mounted fixed temperature, rate-of-rise and combination detectors.

Test Head for Heat Detector Device is required for testing mounted fixed temperature, rate-of-rise and combination detectors when already installed. It has response level of up to 90°C.

SGSK100 is a test kit for Sagittarius series wireless systems.

Test and Commissioning Tools are designed for Wire burn testing/Smoke detectors.

DetectoMat's Testing Device Kit is a cable free testing device with multiple release for smoke, heat and CO detectors

Transparent Flexible Hose is a transparent flexible hose with a steel core of 60m length on request.

The Notifier Remote Detection Probe for UTKLD001L liquid detector.

UTK Rope Contact for roller shutters (roller shutter) detects the lifting, cutting or breaking in of roller shutters. Installation in the box which is completely invisible.

UTK Rope contact analysis card for roller shutters UTKCF01. Manages a maximum of 5 rope contacts. It detects an open line and has a changeover contact relay output.

VESDA Adaptors are produced in red ABS (Acrylonitrile Butadiene Styrene) is a robust polymer, which has the most suitable physical properties for aspirating detection, optimising performance with tensile strength, chemical resistance and ductility.

VESDA capillary pipes and fittings are produced in red ABS under a stringent quality control system.

VESDA Adaptors are produced in red ABS (Acrylonitrile Butadiene Styrene) is a robust polymer, which has the most suitable physical properties for aspirating detection, optimising performance with tensile strength, chemical resistance and ductility.

PIP is a 45 degree pipe elbow by VESDA which is specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system.

VESDA Radius Bends are produced in red ABS under a stringent quality control system. ABS is a robust polymer.

Standard sampling points are designed for a ceiling with a void where micro bore tubes are run in the void and sampling points are mounted in the ceiling.

VESDA-E VEA sampling point and microbore tube is fully supervised by the detector. VEA sampling points are available in two different type standard and surface mount. It can be used in Healthcare, Offices and Electrical cabinets.

VF-Spring for use with old style VF immersion wells.

VSP benchmark test points placed along the pipes run from the ASD and provide a means to validate the integrity of the system and pipe network.

VSP-877 flush-mount sampling points provide a functionally and aesthetically improved alternative to the conical sampling points used in Xtralis® aspirating smoke detection (ASD) pipe networks.

VSP-878 adapter kits are designed to allow the VSP-877 flush-mount sampling points to be used with larger 1/2-inch capillary tubing.

The Gamewell-FCI Velociti® Series Smoke Sensors are addressable projected beam smoke sensors which are uniquely suited to sense smoke in hostile environments or open areas with high ceilings

Ventilation air duct module for usage of the OTblue-LKM 802379 air duct smoke detector in combination with Venturi tubes 781446, 781447 or 781448.

Venturi Air Duct Construction Set includes modules, deteregentes and tubes that are used for leading the air out of the duct through the detection chamber.

Vesda ABS End Caps are a part of Vesda pipe and fittings range.These end caps have been specially developed to provide fully matched components for the optimal performance of the whole VESDA aspirating systems.

The Vesda Conical Sample Point Heads are a part of Vesda aspiring systems and are used for the 10mm capillary aspiration pipe.

Vesda Xtralis Pipe Clip has been designed to secure air sampling pipe using a quick clamp action without the need of additional fixings. These pipe clips are suitable for indoor or outdoor use having excellent resistance to UV, oil and petrol.

Visual/Acoustic Appliances by Notifier are polycarbonate film with "Allarme Incendio" inscription.

Visual/Acoustic appliances are of polycarbonate film with "No Entry Shutdown in Progress" inscription.

Notifier Visual/Acoustic Appliance is a polycarbonate film with "Evacuare il Locale" inscription.

Water Trap has an anti-condensation siphon complete with shut-off valve and tap.

Flexible Connectors are white in color and are available in 30 cm and 100 cm.

The Xtralis 2-Way Ball Valves are designed to control the flow of fluids in Vesda Smoke Detectors.

The VESDA Xtralis PIP-025 is a 25 mm x 12" Condensation Valve Trap with Ball Valve. Aspirating Pipe and Fittings are produced in red ABS under a stringent quality control system.

VESDA-E VEA microbore tubes are custom made, high quality plenum rated flame retardant polyethylene tubes. They have superior stress crack resistance for reliable long-term performance

The Xtralis PIP series is designed to make a better quality pipe system.

The Xtralis Refrigerated Storage Sampling Kits provides a standardised method of smoke sampling for Refrigerated Storage facilities in a considerably improved manner allowing simplified installation with reduced maintenance.

VEA provides assured detection through active sampling and end to end system integrity monitoring.

Honeywell's Xtralis Tamper Proof Sampling Points are a part of Aspiring Smoke Detection. They can minimize the risk of vandalism and tolerate abuse.

The Xtralis Trunk Adapter PIP-016 have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system.

The VESDA-E VEA Microbore tubes are custom made, high quality plenum rated flame retardant polyethylene tubes that are reliable long-term performance. They are lightweight and flexible for easy handling and installation.

The VESDA-E VEA series of detectors are used for early warning smoke detection with pinpoint addressability and a variety of annunciation options that truly surpass traditional spot detectors.

ZT Immersion wells are used for thermostats and temperature transmitters

The ZT Series Nickel Plated Brass Immersion Tube is used in thermostats and temperature transmitter.

The ZT Series Stainless Steel Immersion Tube is used in thermostats and temperature transmitter.

MOD2W maintenance modules allow for communications to 2-wire i³™ Series detectors with any listed fire alarm control panel capable of utilizing this module.

i³™ Series sensitivity readers are battery-powered devices equipped with an infrared optical interface for automatically reading data sent by smoke detectors every 10 seconds. 

Female Air Line Adaptor comes under accessories of pipes and fittings. This is 25mm to 3/8 BSP.