The Excel Web II is Honeywell’s Ethernet-based, freely programmable Building Automation controller. The controller provides network security, universal operation and reduces total installation cost for building investors and building operators.

The high-efficiency F58G,H Commercial Electronic Air Cleaner is mounted to the return air duct of a forced-air heating, cooling, or ventilating system, capturing a significant amount of airborne particles 0.3 micron and larger.

Parts and accessories are for use with foot-mounted motors, such as internal auxiliary switch kits, height adjuster brackets, and screw terminal adapter kits, among others.

A part of the Honeywell Optimizer Suite, the Honeywell Optimizer Unitary Controller allows you to wire them or connect wirelessly – even take advantage of groundbreaking twisted pair T1L technology

Honeywell panel bus I/O modules consist of a terminal sockets and a removable electronic modules, that allow for the sockets to be mounted and wired before the electronic modules are installed.

LonWorks® IF-LON2 interfaces can be used to connect Honeywell controllers via their USB port with LonWorks networks.

M436 spring return actuators are used for 2-position back draft, outdoor air changeover, zone, or minimum position damper control.

M836 spring return actuators are used for residential and some light commercial applications in Series 80 circuits.

P643A1007 Pressuretrol™ pneumatic switches convert pneumatic signals from controllers to electrical switches in order to provide start and stop control.

Pluggable panel bus output modules allow you to monitor and control remote points using 2-wire communication with the main controller.

Pluggable panel bus I/O modules communicate via the LonWorks® bus and panel bus respectively.

Honeywell provides pneumatic actuators for air dampers.

Pneumatic remote bulb temperature controllers provide proportional control of pneumatic valves and damper actuators in HVAC.

Position feedback and SPDT pilot duty auxiliary switches are used in conjunction with ML6984/ML7984 Series 4000 and higher (ML6984 in 5-wire mode only) globe valve actuators.

Q181 auxiliary potentiometers are used to control one to four Modutrol Series 90 motors from one master motor.

The Q181A Auxiliary Potentiometer controls one or two Series 90 auxiliary motors from one master motor.

Q298 damper linkages connect M833, M835, M836, and M7415 economizer motors to 1- or 2-zone dampers. These linkages may be used to link shafts of two dampers together.

Q5001 valve linkages connect Modutrol motors to 2- or 3-way valves. They are used primarily on steam and water valves, such as the V5011 or V5013.

Q605 damper linkages connect Modutrol motors to a standard damper (or dampers) to control the flow of air through ducts. The various models permit the motor to be mounted inside or outside the duct, and on either side of the damper.

RP418 and RP818 electric/pneumatic relays are solenoid valves which open and close the air supply to pneumatic controls. The control input is an on-off line voltage signal to the RP418A-C and 24V AC signal to the RP818A and B.

RP7517 electronic-pneumatic transducers are used in electronic-pneumatic control systems to convert a proportional electric output signal from a controller into a direct-acting, proportional pneumatic signal.

RP920 pneumatic controllers are used in conjunction with remote sensors to provide proportional or proportional plus integral control of temperature, humidity, pressure, or dewpoint in heating and air conditioning systems.

RP970A pneumatic capacity relays are direct acting, proportional relays with a 1:1 pressure ratio.

A secure cloud-based supervisor that enables monitoring and control of the BMS at a single site or a portfolio of multiple sites.

Repack kits are used with VGF valves. The kits include packing, washer, spring, gasket, and lubricant.

S03, S05, S10, S20 Series spring return direct coupled actuators (DCA) are used within HVAC systems. They drive a variety of quarter-turn, final control elements requiring spring return fail-safe operation.

S963 manual potentiometers are used for the checkout of W973 logic panels and W975 satellite sequencers.

Series 61 and Series 62 Modutrol IV™ motors are 3-wire spring return and non-spring return floating control motors.

Series 71, 72, and 76 Modutrol IV™ motors are spring return and non-spring return motors used to control dampers and valves. The motors accept a current or voltage signal from an electronic controller to position a damper or valve.

Series 90 Modutrol IV™ motors are spring return and non-spring return modulating proportional control motors. These motors are used with controllers that provide a Series 90 output to operate dampers or valves.

T675A/B and T678A temperature controllers regulate the temperature of air or liquids in ducts, pipes, tanks, and boilers. Typical uses include control of dampers and valves in heating, cooling, or heating-cooling systems.

TP9600 Series pneumatic thermostats provide proportional control for pneumatic actuators in HVAC systems.

TP970/9600 Series pneumatic thermostat accessories include backplate assemblies, filter assemblies and cartridges, plugs, resistor blocks, wall plates, mounting hardware, thermostat cover kits, satin/chrome cover assemblies, and more.

TP974 are direct-acting, proportioning temperature sensors used with pneumatic controllers to control valve and damper actuators for one- or two-pipe installations.

TR120 touch screen wall modules enable local controller configuration through an easy-to-use touchscreen interface with menu driven selections.

The people in your building want to know that the air they breathe is monitored for their well-being. The TR50 provides simple visual confirmation of air quality, with an optional display to show up to five key components of air health.

V5852A, V5853A, V5862A, and V5863A cartridge globe valves control hot and chilled water for VAV terminals fan coil units, small re-heaters, and re-coolers in temperature controllers.

UEC24014M262 differential pressure switches open or close a switch in response to a change in the pressure across a pump or filter.

Rebuild kits are used with V5011 and V5013 valves.

5112-11/U stem replacement kits are used with VBN2A-H and VBN3A-G ball valves.

VGF flanged globe valves are used for 2-position or modulating control of steam, hot water, or chilled water in closed loop HVAC systems.

14001046-004/U cover fasteners are used with VP527A, VP526A, VP531A/C, VP525A/C pneumatic valves.

CP980 Velocitrol velocity sensor and controllers combine ultra sensitive air velocity sensors with pneumatic controllers to detect and control airflow in air terminal units, independent of system static pressure.

The WTS Series Touch Screen thermostat is a temperature control device with an extra-large LCD display, capacitive touch interface with color icons and manual or automatic fan speed selection.

XFU830A panel bus mixed I/O modules with screw terminals are distributed input/output modules that allow monitoring and controlling remote points with just a 2-wire communication bus back to the main controller.

XL2000 External HMIs are cost effective, versatile mountable human machine interfaces for those Excel Web II controllers not equipped with a built-in HMI.

XS814 auxiliary terminal blocks are for use with EXCEL® 5000 systems. They mount onto already installed pluggable I/O modules in order to equip them with additional terminals.

XSU screw-type terminal sockets are for use with Excel 800 systems.

Zio® LCD wall modules are 2-wire, non-polarity sensitive, Sylk™ bus communicating modules, which function with Spyder® and some ComfortPoint® controllers.

Zio® Lite wall modules are 2-wire, non-polarity sensitive, Sylk™ communicating devices that work with all Spyder® programmable controllers and ComfortPoint™ open controllers enabled with Sylk.